Kohler REVIVAL K-T16119 Bedienungsanleitung

113341-2-BB 2000 Kohler Co.



REVIVAL

DECK-/BATH-MOUNT BATH FAUCET

1. BEFORE YOU BEGIN

HOW TO USE THESE INSTRUCTIONS

Please read these instructions carefully to familiarize

yourselfwiththerequiredtools,materials,andinstallation

sequences. Follow the sections that pertain to your

particular installation. This will aid you in avoiding the

unnecessary expense associated with improper

installation. In addition to proper installation, read all

operating and safety instructions.

All information in these instructions is based on the latest

product information available at the time of publication.

Kohler Co. reserves the right to make changes in product

characteristics, packaging, or availability at any time

without notice.

MODEL NUMBERS

K-T16119

K-T16122

K-T16124

K-T16119M

K-T16122M

K-T16124M

PRODUCT REQUIREMENTS

Deep rough-in kit #73444 allows an additional 1/2”

(1.3cm) of tile thickness.

Plaster guard diameters are approximately 1-5/8”

(4.1cm)forthevalveand7/8”(2.2cm)forthespout.

Installer-supplied copper tubing to be: 5/8” O.D.

(1/2” nominal).

Install water hammer arrestors in supply lines near

the valves.

TOOLS AND MATERIALS REQUIRED

Open end/adjustable wrenches

Adjustable arc pliers

1/2” Nom. (5.8” O.D.) tubing

Tubing Cutter

Hole cutting equipment

Soldering equipment and supplies

Phillips screwdriver

INSTALLER INFORMATION

These instructions cover two methods of

installation: installation on finished deck or bath

rim, and installation on rough (unfinished) deck (to

be covered later with tile or other finish material).

Leave protective sleeve on spout supply tube until

spoutinstallation.ThisisanO-Ringsealingsurface

which may be damaged when unprotected.

Finish deck material must fit closely to the

diameters of the plaster guards, especially the

spout plaster guard.

Provide an access panel to valves from underside

of deck.

2-5/8” (6.7cm) D. 2-5/8” (6.7cm) D.

4-3/8”

(11.1cm)

1-1/8”

(2.9cm)

1-3/4”

(4.4cm)

4-3/4”

(12.1cm)

6-1/4” (15.9cm)

(scroll knob)

6” (15.2cm)

(traditional knob)

9-5/8” (24.4cm) 1-5/8” (4.1cm) 6-5/8” (16.8cm) 1-5/8” (4.1cm)

DECK-MOUNT BATH-MOUNT

6-1/4” (15.9cm)

(scroll knob)

6” (15.2cm)

(traditional knob)

DOME

3” (7.6cm)

1” (2.5cm)

3” (7.6cm)

2-1/2” (6.4cm) D.

4-1/4”

(10.8cm) 1-1/4”

(3.2cm)

2-1/2” (6.4cm)

1” (2.5cm)

TRADITIONAL

4-1/4”

(10.8cm)

2-1/2” (6.4cm) D.

3” (7.6cm)

1” (2.5cm)

3”

(7.6cm)

LEVER 2-1/2” (6.4cm) D.

ROUGHING-IN DIMENSIONS – SPOUT AND HANDLES

Fig. #1

Kohler Co., Kohler, WI

113341-2-BB

ROUGHING-IN DIMENSIONS – CONTINUED

X = Distancefromcenterlineofspoutinlettofrontofspout

base plus 1/2” (1.3cm).

Y = Distance between valve centerlines may vary

depending on your installation requirements.

* Dimension allows for ±1/4” (6mm) handle adjustment

during handle trim installation.

Diameter of hole in deck for spout = 1-1/8” (2.9cm) Max.

Diameter of hole in deck for valve = 1-1/2” (3.8cm) Max.

Thindeck/bathriminstallationsrequireadditional support

under deck/bath rim. Use 1/2” exterior grade plywood.

For installations on a rough (unfinished) deck to be

covered later with tile, the tile thickness must not exceed

1-1/4” (3.2cm).

1/8” (3mm) MIN. - 2-1/8”

(5.4cm) MAX. BATH RIM

THICKNESS

1-13/16” (4.6cm)

5-5/8”

(14.3cm)

7/8” D.

1/2” (1.3cm) MIN. - 2-1/8”

(5.4cm) MAX. DECK

THICKNESS

5/8” O.D. TUBING (1/2” NOM.)

5/8” I.D. (1/2” NOM.)

1-5/16” D.

1-1/8” D.

7/8” D.

1/2” (1.3cm) MIN. - 2-1/8” (5.4cm)

MAX. ROUGH DECK THICKNESS

5/8” O.D. TUBING (1/2” NOM.)

5/8” I.D. (1/2” NOM.)

1-5/16” D.

1-1/8” D.

1-1/4” (3.2cm) MAX.

TILE THICKNESS

FINISHED DECK- AND BATH-MOUNT ROUGHING-IN

ROUGH DECK PLUS FINISHED DECK (TILE) ROUGHING-IN

*1-1/4” (3.2cm)

Fig. #2

4-5/8”

(11.7cm)

2. INSTALLATION

PREPARATION

For installations with 8” (20.3cm) centers using copper

tubing (1/2” nominal, 5/8” O.D.), cut tubing to the lengths

as follows:

2-pieces: 2-7/8” (7.3cm) long

1-piece: 2-3/8” (6cm) long (for finished deck or bath rim

installation only).

For non-8” (20.3cm) center installations, adjust tubing

lengths as necessary.

INSTALL SPOUT SUPPLY TUBE

Slidebrasswasherfrom bottomofspout supply tubeover

threads until washer reaches supply tube shoulder.

Insert spout supply tube through mounting hole from top

of deck/bath rim. Ensure flat portion of washer faces

forward. Spout supply tube will be suspended by washer.

Slide plate (oriented with tabs toward deck) and washer

onto spout supply tube from bottom and thread on

mounting nut. Tighten nut.

Secure plate to deck or wooden support with two wood

screws.

NOTE: Leaveprotective sleeve onspout supplytube un-

til spout installation. Fig. #3

Supply Tube Shoulder Brass Washer

Nut

Spout Supply Tube

Washer

Wood Screw

Plate

Wood Screw

3113341-2-BB

Kohler Co., Kohler, WI

INSTALL VALVE BODIES

Threadone mountingnut, flangeside up,followed byone

fiber washer and one rubber washer onto each valve

body.

Insert the 2-7/8” (7.3cm) long copper tubes between the

valve bodies and 1/2” tee. For a finished deck or bath rim

installation only, insert the 2-3/8” (6cm) long copper tube

into top of tee.

Do not solder connections yet. Fig. #4

Rubber Washer

Fiber Washer

Mounting Nut

Valve Body 2-7/8” (7.3cm)

Copper Tubes

2-3/8” (6cm) Copper Tube

(Finished Deck Or Bath

Rim Installation Only) 1/2”

Tee

NOTE: Orient valve body marked “COLD” so it is on the

right when facing the front of the faucet.

Insert valve bodies through mounting holes from bottom

ofdeck/bathrim.Forfinisheddeckorbathriminstallation,

mate copper tube from tee with spout supply tube. Hold

in place.

Place a collar with flange side up on each valve body and

threaddowntoatleast1”(2.5cm)fromtopthreadonvalve

body.

Install threaded sleeve on each valve body until sleeve

bottoms on valve body.

Back up collar until it contacts sleeve.

Fig. #5

1” (2.5cm)

Collar

Threaded Sleeve

NOTE: For finished deck/bath rim installations, perform

procedures of this frame. For rough (unfinished) deck

installations, omit procedures in this frame and perform

procedures in frames Fig. #7 thru Fig. #11.

Tighten mounting nuts on each valve body underneath

deck/bath rim.

Soldercoppertubestovalvebodies,teeandspoutsupply

tube.

Solder hot and cold water tubes to valve body inlets.

Ensure cold supply is on right hand side.

Proceed to Section 3. Fig. #6

Solder

Hot

Supply Solder

Cold

Supply

Solder

Kohler Co., Kohler, WI

113341-2-BB

NOTE: This frame applicable to rough (unfinished) deck

installations only.

Set Valve Body Height: Use one of the following two

formulas to calculate the valve body clearance required

for the finish material at your installation.

If tile to be installed measures less than 1” (2.5cm) thick,

add that measurement to 1-1/4” (3.2cm).

Example#1:Tilethickness(3/4”(1.9cm))+1-1/4”(3.2cm)

= 2” (5.1cm) clearance.

Ifthetiletobeinstalledmeasuresbetween1”(2.5cm)and

1-1/4”(3.2cm)thick,addonly1”(2.5cm)to1-1/4”(3.2cm).

Example#2: Tilethickness (1-1/8” (2.9cm))=1” (2.5cm) +

1-1/4” (3.2cm) = 2-1/4” (5.7cm) clearance.

Adjust threaded collar until the dimension from the top of

the sleeve to the top of the rough deck surface equals the

clearance requirement you calculated.

Note this dimension. You will need to use it again after

connecting the supply tube.

Fig. #7

ÀÀÀÀÀ

ÉÉÉÉÉ

Tile Thickness

2-1/8”

(5.4cm)

Max.

2” (5.1cm)

Clearance

1-1/4” (3.2cm)Top Of Sleeve

Threaded

Collar

Rough Deck

3/4” (1.9cm)

EXAMPLE #1

ÀÀÀÀÀ

ÉÉÉÉÉ

Tile Thickness

2-1/8”

(5.4cm)

Max.

2-1/4” (5.7cm)

Clearance

1-1/4” (3.2cm)Top Of Sleeve

Threaded

Collar

Rough Deck

1-1/8” (2.9cm)

EXAMPLE #2

NOTE: This frame applicable to rough (unfinished) deck

installations only.

Supply Tube Connection: Measure distance from

bottom of spout supply tube to top of tee.

Add 1” (2.5cm) to this measurement and cut a piece of

1/2”nominal(5/8”O.D.)coppertubingtofitintothesupply

tube and tee port.

Fig. #8

Spout Supply Tube

Tee

Measure

Distance

NOTE: This frame applicable to rough (unfinished) deck

installations only.

Back off threaded collars as far as possible without

removing them. Pivot the valve bodies enough to remove

the tee and two pieces of tubing. (If valve body holes are

smaller than recommended, it may be necessary to

remove the entire valve body assembly.)

Install tubing into tee. Mate copper tube from tee with

spout supply tube. Pivot the valve bodies onto the two

pieces of copper tubing.

Do not solder at this time. Fig. #9

Sleeve

Threaded

Collar

Rough

Deck

Mounting

Nut Copper

Tube

Spout Supply

Tube

Tee

5113341-2-BB

Kohler Co., Kohler, WI

NOTE: This frame applicable to rough (unfinished) deck

installations only.

Reset Valve Body Height: Adjust the threaded collars

until the dimension from the top of sleeve to the top of the

roughdeck surface equals the theclearance requirement

you calculated in frame Fig. #7 .

Fig. #10

ÀÀÀÀ

ÉÉÉÉ

Tile Thickness

Top Of Sleeve

Threaded Collar

Rough Deck

Pre-Determined

Clearance

Requirement

NOTE: This frame applicable to rough (unfinished) deck

installations only.

Tighten mounting nuts on each valve body underneath

deck.

Soldercoppertubestovalvebodies,teeandspoutsupply

tube.

Ensure cold supply is on right hand side.

Solder hot and cold water supply tubes to valve body

inlets.

Proceed to Section 3.

Fig. #11

Solder Cold

Supply

Solder

Hot

Supply

Mounting

Nut Solder

Copper

Tube

Rough

Deck

Spout Supply Tube

Valve

Body

3. INSTALLATION CHECKOUT (ALL INSTALLATIONS)

Thread 3/8” pipe plug into top of spout supply tube.

Ensurevalvesareclosed(coldfullycounterclockwise,hot

fully clockwise).

Turn on main water supply and check complete

installation for leaks with valves closed and open. Repair

as required.

Close both valves. Turn off main water supply.

WARNING: Risk of personal injury. Lines will be

pressurized.Donotleanoverpipeplugwhenturning

or removing the plug.

Wrapa towelaroundthe pipeplugto prevent waterspray.

Water will purge from the supply tube when you remove

the plug.

Carefully back out pipe plug to relieve pressure.

Thread pipe plug into spout supply tube. Leave pipe plug

installed until spout and handle installation.

Install cardboard plaster guards over both valves and

spout supply tube. Leave in place until spout and handle

installation.

Fig. #12

3/8” Pipe Plug CLOSE

COLD

HOT

Kohler Co., Kohler, WI

113341-2-BB

4. INSTALL TILE (IF APPLICABLE)

Verify that there will be a 1” (2.5cm) to 1-1/2” (3.8cm)

distance from the top of the sleeve to the top of the tile. If

not, do not install tile due to improper valve installation.

If proper clearance exists, install tile up to plaster guards

on valves and spout supply tube.

Fig. #13

Sleeve

Threaded

Collar

Rough

Deck

Tile

Spout

Supply

Tube

1” (2.5cm)

MIN. 1-1/2”

(3.8cm) MAX.

5. INSTALL SPOUT

Ensurevalvesareclosed(coldfullycounterclockwise,hot

fully clockwise).

Turn off main water supply.

WARNING: Risk of personal injury. Lines may be

pressurized.Donotleanoverpipeplugwhenturning

or removing the plug.

Wrapa towelaroundthe pipeplugto prevent waterspray.

Water may purge from the supply tube when you remove

the plug.

Carefully remove pipe plug.

Fig. #14

3/8” Pipe Plug CLOSE

COLD

HOT

Removecardboard plaster guardfrom spout supply tube.

Cut off spout supply tube 1-1/4” (3.2cm) above the bath

rim, finished deck or tile.

CAUTION: Risk of product damage. Ensure all

burrs are removed from supply tube to prevent

damage to O-Ring seal inside the sleeve.

Fig. #15

1-1/4” (3.2cm)

Tile

Finish

Rough

Deck

Spout

Supply

Tube

7113341-2-BB

Kohler Co., Kohler, WI

NOTE: Following step is applicable to a tile covered

rough deck installation only.

Slide brass washer, flat side facing forward, on spout

supply tube. Brass washer is furnished with spout.

NOTE: Washer is not needed for bath rim/finished deck

installation.

Fig. #16

Spout

Supply Tube

Rough Deck

Finished Deck

Brass Washer

Back off screws in sleeve, and with a twisting motion

installsleeveonspoutsupplytubeuntilitcontactswasher

surface.

Alignsleeve so that screws are notfacing directlyforward

or backwards. Tighten screws.

Fig. #17

Screws

Sleeve

CAUTION: Risk of product damage. Use care

when installing spout assembly to prevent damage

to O-Ring seal on outside of sleeve.

Place ring of plumbers putty around underside of spout.

Install spout on sleeve by carefully pressing down until

spout base contacts deck, bath rim, or tile. Align spout as

desired and tighten screw.

Screw

Fig. #18

O-Ring

Plumbers

Putty

6. INSTALL HANDLES

Remove the plaster guard from the valve, and discard it.

Remove the threaded sleeve from the valve, and discard it.

Fig. #19

Sleeve

Valve

Press the stem extension onto the valve stem.

NOTE: A spline adapter is provided in addition to the

stem extension, and is the shorter of the two pieces. The

spline adapter will not be used in deck- and bath-mount

installations.

Fig. #20

Stem Extension

Valve Stem

Valve Body

Kohler Co., Kohler, WI

113341-2-BB

Applyaringofplumbersputtyaroundtheundersideofthe

handle skirt. Thread the assembled handle and skirt to

the valve body until it contacts the finished wall.

Be sure to properly align Traditional and Lever handle

styles. Remove and rotate the spline adapter to provide

proper handle alignment.

NOTE: The stem extension allows for fine adjustment of

Traditional and Lever handle alignment. To refine the

alignment, unthread the handle and skirt, and reposition

the stem extension on the valve stem. Rethread the

handleandskirt,andcheckthehandlealignment.Repeat

until the alignment is satisfactory.

Repeat for the other handle. Fig. #21

Handle and Skirt

(Lever Handle

Shown)

Stem Extension

Apply Plumbers

Putty

7. CALL US FOR HELP

Questions? Problems? First review the installation instructions to ensure correct installation. For additional

assistance, call our Customer Service Department for direct help. You may also contact us at our web site listed

below.

In the U.S.A. call 1-800-4-KOHLER

In Mexico call 001-877-680-1310

In Canada call 1-800-964-5590

www.kohlerco.com

Andere Handbücher für REVIVAL K-T16119

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kohler Sanitärprodukte Handbücher

Kohler

Kohler K-7914 Montageanleitung

Kohler

Kohler K-6356 Bedienungsanleitung

Kohler

Kohler K-994 Bedienungsanleitung

Kohler

Kohler K-8499 Montageanleitung

Kohler

Kohler K-9245 Montageanleitung

Kohler

Kohler K-514 Bedienungsanleitung

Kohler

Kohler Karbon K-6227D Bedienungsanleitung

Kohler

Kohler Antique K-100 Montageanleitung

Kohler

Kohler K-16012-4 Bedienungsanleitung

Kohler

Kohler Oblo K-103B87-SANA-CP Bedienungsanleitung

Kohler

Kohler K-18829 Montageanleitung

Kohler

Kohler ODEON K-8766 Bedienungsanleitung

Kohler

Kohler 4179A-NA Bedienungsanleitung

Kohler

Kohler 10282 Bedienungsanleitung

Kohler

Kohler K-697 Montageanleitung

Kohler

Kohler Candide 660 Series Montageanleitung

Kohler

Kohler KELSTON K-2382 Kurzanleitung

Kohler

Kohler TAUT 73194T-4 Bedienungsanleitung

Kohler

Kohler TAUT 24572X-4A Bedienungsanleitung

Kohler

Kohler K-6814-3 Montageanleitung

Kohler

Kohler K-2367 Bedienungsanleitung

Kohler

Kohler COMPOSED K-20257T-B-CP Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Kohler

Kohler KUMIN 18655T-CP Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Bristan

Bristan PS2 BAS C D2 Verdrahtungsschema

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung

Sanela

Sanela SLVN 07 Bedienungsanleitung

Glacier bay

Glacier bay DORIND HD67478W-6001 Montageanleitung

Sterling Plumbing

Sterling Plumbing C741 Bedienungsanleitung