Lippert RV Bedienungsanleitung

RV Structural guidelines

Rev: 11.11.21 Page 2 CCD-0004203

TABLE OF CONTENTS

I-Beam (3/1/2021) 3

Stick and Tin 3

Stick and Tin Continued 4

Laminated Side Walls 4

Laminated Side Walls Continued 5

Crush Tube 6

Standard Crush Tubes/Riser Tubes ( 7/13/2021) 6

Crush Tubes Taller Than 2" including Extended Length Crush Tubes 6

The Extended Length Crush Tube 6

Chassis w/ Crush Tube 6

Draw Bar 7

Standard TT Draw Bar Engineering Guideline Rev. (6/15/2021) 7

Draw Bar 8

Toy Hauler TT Draw Bar Engineering Guidelines Rev: (6/15/2021) 8

Accepted Tube/I-Beam RV Engineering Guidelines Rev: (1/1/2020) 9

Outrigger 10

Engineering Guidelines Rev: (7/13/2021) 10

Hanger Support - Beam Stiener 11

Hanger Support Requirements (7/13/2021) 11

Axle Area - FHXM 12

Axle Area Full Height XMs Engineering Guidelines Rev: (1/1/2020) 12

Full Height Cross Member Requirements in the Axle Area 13

Upper Deck Main 14

Accepted Upper Deck RV Engineering Guidelines Rev: (3/1/2021) 14

Upper Deck Riser 15

Accepted Upper Deck RV Engineering Guidelines Rev: (3/1/2021) 15

Leveling 16

Accepted Leveling RV Engineering Guidelines - REV : (1/1/2020) 16

Accepted Travel Trailer Leveling RV Engineering Guidelines - REV : (1/1/2019) 17

Hydraulic Landing - Level Bracket 18

Accepted HYD Landing Gear and Leveling Bracket Supports Engineering Guidelines - REV: (3/1/2021) 18

5th Wheel Drop Gen set up. 19

Bumper Extension 20

Accepted Bumper Extension Engineering Guidelines - REV : (3/1/2021) 20

Slide-out Room Bar 21

Slide out/Room Bar Engineering Guidelines Rev: (3/1/2021) 21

Note: 22

Proprietary and Condential

The information contained in this document is the sole property of Lippert Components, Inc.

Any reproduction in parts or as a whole without the written permission of Lippert Components, Inc.

Is prohibited.

Rev: 11.11.21 Page 3 CCD-0004203

I-Beam (3/1/2021)

Stick and Tin

3.1 Stick and Tin Hung Glass Side Walls RV Engineering Guidelines

Conventional Travel Trailer

Max Main Rail

Length All

lengths are ≤

21' 25' 26' 27' 28' 29' 30' 31' 32' 33' 34' 35' 36' 37' 38' 39' 40' 41' 42'

252" 300" 312" 324" 336" 348" 360" 372" 384" 396" 408" 420" 432" 444" 456" 468" 480" 492" 504"

# Of Slides* Under 8K GVWR** Over 8K GVWR

0 6 6 6 6 8 8 8 8 8 8 8 8 8 8 10 10 10 12 12

1 6 8 8 8 8 8 8 8 8 10 10 10 10 10 10 10 10 12 12

2 8 8 8 8 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12

3 10 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

4 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

3.3 Stick and Tin Hung Glass Side Walls RV Engineering Guidelines

Conventional 5th Wheel

Max Main Rail

Length All

lengths are ≤

21' 25' 26' 27' 28' 29' 30' 31' 32' 33' 34' 35' 36' 37' 38' 39' 40' 41' 42'

252" 300" 312" 324" 336" 348" 360" 372" 384" 396" 408" 420" 432" 444" 456" 468" 480" 492" 504"

# Of Slides*

0 8 8 8 8 8 8 10 10 10 10 10 10 10 10 12 12 12 12 12

1 8 8 8 8 8 10 10 10 10 10 10 10 10 10 12 12 12 12 12

2 8 8 8 8 10 10 10 10 10 10 10 10 10 10 12 12 12 12 12

3 8 8 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 12

4 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12

3.2 Stick and Tin Hung Glass Side Walls RV Engineering Guidelines

Toy Hauler Travel Trailer

Max Main Rail

Length All

lengths are ≤

21' 25' 26' 27' 28' 29' 30' 31' 32' 33' 34' 35' 36' 37' 38' 39' 40' 41' 42'

252" 300" 312" 324" 336" 348" 360" 372" 384" 396" 408" 420" 432" 444" 456" 468" 480" 492" 504"

# Of Slides* Under 8K GVWR** Over 8K GVWR

0 6 6 8 8 8 10 10 10 10 10 10 10 10 10 12 12 12 12 12

1 6 8 8 8 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12

2 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 12

3 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

4 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

Rev: 11.11.21 Page 4 CCD-0004203

Stick and Tin Continued

Laminated Side Walls

4.1 Stick and Tin Hung Glass Side Walls RV Engineering Guidelines

Toy Hauler 5th Wheel

Max Main Rail

Length All

lengths are ≤

21' 25' 26' 27' 28' 29' 30' 31' 32' 33' 34' 35' 36' 37' 38' 39' 40' 41' 42'

252" 300" 312" 324" 336" 348" 360" 372" 384" 396" 408" 420" 432" 444" 456" 468" 480" 492" 504"

# Of Slides*

0 8 8 8 8 8 8 10 10 12 12 12 12 12 12 12 12 12 12 12

1 8 8 8 8 8 10 10 12 12 12 12 12 12 12 12 12 12 12 12

2 8 8 8 8 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12

3 8 8 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

4 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

4.2 Laminated Side Walls RV Engineering Guidelines

Conventional Travel Trailer

Max Main Rail

Length All

lengths are ≤

21' 25' 26' 27' 28' 29' 30' 31' 32' 33' 34' 35' 36' 37' 38' 39' 40' 41' 42'

252" 300" 312" 324" 336" 348" 360" 372" 384" 396" 408" 420" 432" 444" 456" 468" 480" 492" 504"

# Of Slides* Under 8K GVWR** Over 8K GVWR

0 6 6 6 6 8 8 8 8 8 8 8 8 8 8 10 10 10 12 12

1 6 6 8 8 8 8 8 8 8 10 10 10 10 10 10 10 10 12 12

2 8 8 8 8 8 8 10 10 10 10 10 10 10 10 12 12 12 12 12

3 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 12

4 10 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

4.3 Laminated Side Walls RV Engineering Guidelines

Toy Hauler Travel Trailer

Max Main Rail

Length All

lengths are ≤

21' 25' 26' 27' 28' 29' 30' 31' 32' 33' 34' 35' 36' 37' 38' 39' 40' 41' 42'

252" 300" 312" 324" 336" 348" 360" 372" 384" 396" 408" 420" 432" 444" 456" 468" 480" 492" 504"

# Of Slides* Under 8K GVWR** Over 8K GVWR

0 6 6 6 8 8 8 10 10 10 10 10 10 10 10 12 12 12 12 12

1 6 8 8 8 8 10 10 10 10 10 10 10 12 12 12 12 12 12 12

2 8 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12

3 8 8 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12

4 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

Rev: 11.11.21 Page 5 CCD-0004203

Laminated Side Walls Continued

5.1 Laminated Side Walls RV Engineering Guidelines Rev: 01.01.20

Conventional 5th Wheel

Max Main Rail

Length All

lengths are ≤

21' 25' 26' 27' 28' 29' 30' 31' 32' 33' 34' 35' 36' 37' 38' 39' 40' 41' 42'

252" 300" 312" 324" 336" 348" 360" 372" 384" 396" 408" 420" 432" 444" 456" 468" 480" 492" 504"

# Of Slides*

0 8 8 8 8 8 8 8 8 8 8 8 10 10 10 10 10 10 10 10

1 8 8 8 8 8 8 8 8 8 8 8 10 10 10 10 10 10 10 10

2 8 8 8 8 8 8 10 10 10 10 10 10 10 10 12 12 12 12 12

3 8 8 8 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 12

4 10 10 10 10 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12

5.2 Laminated Side Walls RV Engineering Guidelines Rev: 01.01.20

Toy Hauler 5th Wheel

Max Main Rail

Length All

lengths are ≤

21' 25' 26' 27' 28' 29' 30' 31' 32' 33' 34' 35' 36' 37' 38' 39' 40' 41' 42'

252" 300" 312" 324" 336" 348" 360" 372" 384" 396" 408" 420" 432" 444" 456" 468" 480" 492" 504"

# Of Slides*

0 8 8 8 8 8 8 8 10 10 10 12 12 12 12 12 12 12 12 12

1 8 8 8 8 8 8 10 10 10 12 12 12 12 12 12 12 12 12 12

2 8 8 8 8 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12

3 8 8 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12

4 10 10 10 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12 12

Drop Deck Max Recommended Beam

Beam Size Max Drop Length

This dimension is measured from the front of the drop beam to the

front of the top stacked beam and does not include where the two

beams overlap. 24" of I-beam overlap is required.

6" 4.4# Beam 60" If GVWR is greater than 8K for a TT or 10K for a

5th wheel, then 8" 6.5# minimum

8" 6.5# Beam 101" If GVWR is greater than 18K, then 8" 10# minimum

8" 10# or 10" 8# Beam 142"

5.3 Units with a 1-¼" receiver hitch need to add 12" to current main rail length to determine I-beam size needed.

5.4 Units with a 2" receiver hitch or rear storage rack need to add 24" to current main rail length to

determine I-beam size needed.

A. * # Of Slides Include: In Frame Slide - In Wall Slide - Above Floor Slide - Outside Kitchen (excludes

slides in the upper deck).

- Outside Kitchen definition: if the opening in the sidewall is larger than 24 square feet or the

opening isn't fully framed inside the sidewall, then it must be counted as a slide out.

B. - Outside Kitchen examples of opening not being fully framed: bottom tube of sidewall removed/

cut out, main floors outside rail removed/cut out for outside kitchen to sit partially below floor.

5.5 Main rail length needs to include drop deck length.

5.6 When a 2" extended length crush tube is used, you can drop a main rail size. See notes in sec. 2.3 for

layout details.

C. ** If chassis meets length/slide count but doesn't meet the GVWR spec, then it must go up to 8"

I-beam size or use a 2" extended crush tube.

Rev: 11.11.21 Page 6 CCD-0004203

Crush Tube

Standard Crush Tubes/Riser Tubes ( 7/13/2021)

6.1 Need to extend a minimum of 2 ¼" past the end of the standard hangers and ½" past the end of

torsion hangers.

Set cross tubes ¼" in from the end of the crush tube.

2¼"2¼"

½"½"

354⁄"

40%

100%

Crush Tubes Taller Than 2" including Extended Length Crush Tubes

6.2 Standard length crush tubes ≤ 4" require a 2x2 - 11ga cross tube support at the front and rear of the

crush tube, also require two full height XMs in the axle area.

Note: Standard length crush tubes ≥ 5" require a 2x4 -11ga cross tube support at the front and rear of the

crush tube, also require two full height XMs in the axle area.

Note: Crush tube taller than 6" needs Lippert management approval.

The Extended Length Crush Tube

6.3 Start a minimum of 12" in front hanger or riser tube and extend 40% of the rear overhang. It also needs

to be rounded up to the nearest 12" increment.

Note: Extended length crush tubes ≥ 4" require a 2x2 - 11ga cross tube supports at the front and rear of

the axle area and extended length crush tubes ≥ 5" require a 2x4 - 11ga at the front and rear of the

axle area.

Chassis w/ Crush Tube

6.4 That are either a triple axle or using axles rated ≥ 8K, crush tube is required to be 7ga.

¼"

3"+

100%

382⁄"

40%

12"

Rev: 11.11.21 Page 7 CCD-0004203

Draw Bar

Standard TT Draw Bar Engineering Guideline Rev. (6/15/2021)

7.1 7.4

GVWR ≤ 50" BALL CENTER GVWR 54.5"-56" BALL CENTER

≤ 5,550 2X4 11GA ≤ 4,900 2X4 11GA

5,551 - 7,850 2X5 11GA 4,901 - 7,000 2X5 11GA

7,851 - 10,500 2X6 11GA 7,001 - 9,350 2X6 11GA

10,501 - 15,000 2X6 7GA 9,351 - 13,300 2X6 7GA

15,001 - 18,200 2X6 1/4GA 13,301 16,300 2X6 1/4GA

7.2 7.5

GVWR 50.5"-52" BALL CENTER GVWR 56.5"-58" BALL CENTER

≤ 5,300 2X4 11GA ≤ 4,800 2X4 11GA

5,301 - 7,550 2X5 11GA 4,801 - 6,700 2X5 11GA

7,551 - 10,000 2X6 11GA 6,701 - 9,000 2X6 11GA

10,001 - 14,000 2X6 7GA 9,001 - 12,900 2X6 7GA

14,001 - 17,500 2X6 1/4GA 12,901 -15,200 2X6 1/4GA

7.3 7.6

GVWR 52.5"-54" BALL CENTER GVWR 58.5"-60" BALL CENTER

≤ 5,150 2X4 11GA ≤ 4,600 2X4 11GA

5,151 - 7,250 2X5 11GA 4,601 - 6,500 2X5 11GA

7,251 - 9,700 2X6 11GA 6,501 - 8,700 2X6 11GA

9,701 - 13,800 2X6 7GA 8,701 - 12,500 2X6 7GA

13,801 -16,900 2X6 1/4GA 12,501 -15,200 2X6 1/4GA

For any guideline questions please contact: [email protected]

Rev: 11.11.21 Page 8 CCD-0004203

Draw Bar

Toy Hauler TT Draw Bar Engineering Guidelines Rev: (6/15/2021)

8.1 8.4

GVWR ≤ 50" BALL CENTER GVWR 54.5"-56" BALL CENTER

≤ 4,150 2X4 11GA ≤ 3,700 2X4 11GA

4,151 -5,900 2X5 11GA 3,701 - 5,250 2X5 11GA

5,901 - 7,850 2X6 11GA 5,251 - 7,000 2X6 11GA

7,851 - 11,200 2X6 7GA 7,001 - 10,000 2X6 7GA

11,201 - 13,700 2X6 1/4GA 10,001 - 12,200 2X6 1/4GA

8.2 8.5

GVWR 50.5"-52" BALL CENTER GVWR 56.5"-58" BALL CENTER

≤ 4,000 2X4 11GA ≤ 3,600 2X4 11GA

4,001 -5,650 2X5 11GA 3,601 - 5,050 2X5 11GA

5,651 - 7,550 2X6 11GA 5,051 - 6,750 2X6 11GA

7,551 - 10,800 2X6 7GA 6,751 - 9,650 2X6 7GA

10,801 - 13,100 2X6 1/4GA 9,651 -11,800 2X6 1/4GA

8.3 8.6

GVWR 52.5"-54" BALL CENTER GVWR 58.5"-60" BALL CENTER

≤ 3,850 2X4 11GA ≤ 3,450 2X4 11GA

3,851 - 5,450 2X5 11GA 4,101 - 4,900 2X5 11GA

5,451 - 7,250 2X6 11GA 4,901 - 6,550 2X6 11GA

7,251 - 10,400 2X6 7GA 6,551 - 9,350 2X6 7GA

10,401 -12,650 2X6 1/4GA 9,351 - 11,400 2X6 1/4GA

8.7 2x3 Draw bars require Lippert manager approval.

8.8 Please keep ball center to half inch increments.

8.9 Structural XMC can be used in place of tube draw bars in some instances; see Lippert management for

specific details.

8.10 Any chassis with I-beam mains and through mount drawbars where the GVWR/ball center requires

the drawbars to be the same height as the chassis mains, the chassis mains will need to go up a size or

change to undermount drawbar setup

Rev: 11.11.21 Page 9 CCD-0004203

Accepted Tube/I-Beam RV Engineering Guidelines Rev: (1/1/2020)

9.1 Non-Cargo - Hard Side Laminate Floors / Walls Tube & I-beam Chassis

Main Rail Length Feet <12' (camber

0-⁄") 13'-17' camber ⁄" 18'-22' (camber

⁄"-¼") 23'- 25' (camber ¼"-⁄")

Main Rail Length Inch. < 144" 145" - 215" 216" - 264" 265" - 300"

0 Slides 13ga/4" Tube 13ga/4" Tube 11ga/4" Tube 13ga/5" Tube or 6"

I-beam

(1) In-Wall Slide 13ga/4" Tube 11ga/4,13ga/5" Tube

or 6" I-beam

13ga/5" Tube or 6"

I-beam

11ga/5" Tube or 6"

I-beam

9.2 Non-Cargo - Wood Floors / Laminate Walls Tube & I-beam Chassis

Main Rail Length Feet <12' (camber

0-⁄") 13'-17' camber ⁄" 18'-22' (camber

⁄"-¼") 23'- 25' (camber ¼"-⁄")

Main Rail Length Inch. < 144" 144" - 215" 216" - 264" 265" - 300"

0 Slides 13ga/4" Tube 13ga/4" Tube 11ga/4",13ga/5"

Tube or 6" I-beam

13ga/5" Tube or 6"

I-beam

9.3 Non-Cargo - Stick & Tin Tube & I-beam Chassis

Main Rail Length Feet <12' (camber

0-⁄") 13'-17' camber ⁄" 18'-22' (camber

⁄"-¼") 23'- 25' (camber ¼"-⁄")

Main Rail Length Inch. < 144" 144" - 215" 216" - 264" 265" - 300"

0 Slides 13ga/4" Tube 11ga/4",13ga/5"

Tube or 6" I-beam

11ga/4",13ga/5"

Tube or 6" I-beam 11ga/5" or 6" beam

9.5 Pop Up Tent Campers

Main Rail Length Feet < 7.5' 7.5 - 16'

Main Rail Length Inch. <90" 91" - 192"

0 Slides 11ga/3" 13ga/4" Tube

For any guideline questions please contact: [email protected]

9.6 Please contact your current Lippert engineering team lead for all new tube chassis request.

Rev: 11.11.21 Page 10 CCD-0004203

Outrigger

Engineering Guidelines Rev: (7/13/2021)

10.1 Outrigger spacing should be 48" or less.

10.2 Need to have an outrigger on each end of the wheel well area.

10.3 Outrigger height needs to be greater than ½ the main rail height on I-beam frames and full height

on tube & XMC frames. Slide outriggers are an exception.

Slide Arms

Room Bar

FLOOR

A full length outrigger

should be located a maximum of

3" & 24" from notch in the main

floor at the beginning and end of

the slide-out opening

Must have two full length

outriggers in front of or behind

each slide-out.

Must have two full length

outriggers in front of or behind

each slide-out.

A minimum of two slide outriggers must be placed in the slide

out area. They need to be placed under the heaviest area

of the room. If the room is at least 144", a third outrigger is

required. Add an additional outrigger every 48" thereafter.

Must have two full length

outriggers in front of or behind

each slide-out.

Must have two full length

outriggers in front of or behind

each slide-out.

For a stick/tin build, we require a minimum of two slide

outriggers to be placed in the slide out area. They need

to be placed under the heaviest area of the room. If the

room is at least 72", a third outrigger is required. Add an

additional outrigger every 36" thereafter.

For a laminated build where rollers are mounted to the floor, we require a

minimum of two slide outriggers to be placed in the slide out area. They need

to be placed under the heaviest area of the room. If the room is at least 144", a

third outrigger is required. Add an additional outrigger every 48" thereafter.

Slide-out Room

FLOOR

A full length outrigger

should be located a maximum of

3" & 24" from notch in

the main floor at the beginning

and end of the slide-out opening

10.4 Through frame slide-out outrigger guidelines for stick and tin/hung glass & laminated sidewalls.

10.5 In wall floor slide-out outrigger guidelines for stick and tin/hung glass & laminated sidewalls.

10.6 For laminated builds where there is at least 6" of wall structure and rollers are mounted on the wall,

only standard outrigger placement will apply every 48".

10.7 If you have a 12 CU. FT. or larger refrigerator in a slideout, you are required to have two slide

outriggers centered under that section of the slideout, spaced no closer than 12” and no further than 36”.

If refer is near tires, both outriggers need to be placed as close as possible to the refer without causing tire

interference. All other slideout outrigger spacing is still applicable.

3" Max

24" Max

Slide-out Room

24" Max

3" Max

Inhaltsverzeichnis

Andere Lippert Autozubehör Handbücher

Lippert

Lippert ARIES 2500207 Bedienungsanleitung

Lippert

Lippert Project 2000 Sliding Step Bedienungsanleitung

Lippert

Lippert Tire Linc Montageanleitung

Lippert

Lippert Curt 18110 Bedienungsanleitung

Lippert

Lippert 10570 Gebrauchsanweisung

Lippert

Lippert 2021000090 Montageanleitung

Lippert

Lippert Kwikee Step Well Cover Bedienungsanleitung

Lippert

Lippert SolidStep 4.0 Bedienungsanleitung

Lippert

Lippert Stargazer Nano Long Skylight Bedienungsanleitung

Lippert

Lippert THEATER SEATING Gebrauchs- und Pflegehandbuch

Lippert

Lippert 2000 Series Bedienungsanleitung

Lippert

Lippert SMART BED UNIVERSAL KIT Bedienungsanleitung

Lippert

Lippert Thin Shade 806621 Montageanleitung

Lippert

Lippert Sway Command 1.5 Bedienungsanleitung

Lippert

Lippert OneControl Bedienungsanleitung

Lippert

Lippert TI-276 Bedienungsanleitung

Lippert

Lippert Thule 5200 Gebrauchs- und Pflegehandbuch

Lippert

Lippert ARIES S224050 Bedienungsanleitung

Lippert

Lippert Level-up Bedienungsanleitung

Lippert

Lippert Promaster Bedienungsanleitung

Lippert

Lippert Stargazer Nano Wide Skylight Bedienungsanleitung

Lippert

Lippert Power Steps 2.0 Bedienungsanleitung

Lippert

Lippert Tire Linc 2020106863 Montageanleitung

Lippert

Lippert CURT 45937 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Renault

Renault 77 11 423 180 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung