M-system R3-CZ4 Bedienungsanleitung

R3-CZ4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8447 Rev.2 P. 1 / 3

ZERO-PHASE CURRENT INPUT MODULE

(with noise lter)

MODEL R3-CZ4

INSTRUCTION MANUAL

BEFORE USE ....

Thank you for choosing M-System. Before use, please check

the contents of the package you received as outlined below.

If you have any problems or questions with the product,

please contact M-System’s Sales Ofﬁce or representatives.

■PACKAGE INCLUDES:

CT input module.............................................................(1)

■MODEL NO.

Conﬁrm Model No. marking on the side of the product to be

exactly what you ordered.

■INSTRUCTION MANUAL

This manual describes necessary points of caution when

you use this product, including installation, connection and

basic maintenance procedures.

POINTS OF CAUTION

■HOT INSERTION/REMOVAL OF MODULES

•Removing or replacing modules does not affect other mod-

ules on the same backplane. It is possible to replace them

without removing the power supply. However, replacing

multiple modules at once may greatly change line voltage

levels. We recommend that you replace them one by one.

■ENVIRONMENT

•Indoor use

•When heavy dust or metal particles are present in the

air, install the unit inside proper housing with sufﬁcient

ventilation.

•Do not install the unit where it is subjected to continuous

vibration. Do not subject the unit to physical impact.

•Environmental temperature must be within -10 to +55°C

(14 to 131°F) with relative humidity within 30 to 90% RH

in order to ensure adequate life span and operation.

■WIRING

•Do not install cables close to noise sources (relay drive

cable, high frequency line, etc.).

•Do not bind these cables together with those in which

noises are present. Do not install them in the same duct.

■AND ....

•The unit is designed to function as soon as power is sup-

plied, however, a warm up for 10 minutes is required for

satisfying complete performance described in the data

sheet.

INSTALLATION

Use the Installation Base (model: R3-BSx).

R3-CZ4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8447 Rev.2 P. 2 / 3

COMPONENT IDENTIFICATION

SW1SW2

SW3

■ FRONT VIEW ■SIDE VIEW

ERR LED

RUN LED

Conv.

Rate

Input 2 (SW1)

Input 4 (SW2)

Range

Input 1 (SW1)

Input 3 (SW2)

Functions

■STATUS INDICATOR LED

RUN indicator: Bi-color (red/green) LED;

Red when the bus A operates normally;

Green when the bus B operates normally;

Amber when both buses operate normally.

ERR indicator: Bi-color (red/green) LED;

Red with the input abnormality;

Green in normal operating conditions.

■SIDE DIP SW

• Input Range: SW1, SW2

INPUT 1 (SW 1) INPUT 2 (SW 1)

RANGEINPUT 3 (SW 2) INPUT 4 (SW 2)

12345678

OFF OFF OFF OFF OFF OFF OFF OFF

0 – 1.5mA (*)

OFF OFF OFF

0 – 0.1mA

• Conversion Rate: SW3

SW CONVERSION RATE

80 ms (*)40 ms 20 ms 10 ms

SW3-1 OFF ON OFF ON

SW3-2 OFF OFF ON ON

(*) Factory setting

Note: Be sure to set unused SW3-3 and 3-4 to OFF.

PC CONFIGURATOR

The following parameters can be set with using PC Conﬁgurator Software (model: R3CON):

•0% scaling value

•100% scaling value

•0% adjustment value (bias)

•100% adjustment value (gain)

•0% input value

•100% input value

•Disable the unused channel

R3-CZ4

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN

Phone: +81(6)6659-8201 Fax:

+81(6)6659-8510 E-mail: info@m-system.co.jp

EM-8447 Rev.2 P. 3 / 3

TERMINAL CONNECTIONS

Connect the unit as in the diagram below.

■DIMENSIONS mm (inch)

130 (5.12)

27.5 (1.08) 109 (4.29)

7.9 (.31)

POSITIONING

GUIDE

TERMINAL

COVER

10–M3.5

SCREW

■CONNECTION DIAGRAM

BUS CONNECTOR

INTERNAL POWER

INTERNAL

BUS A

INTERNAL

BUS B*

*For dual redundant communication.

INPUT 1

LOAD

SOURCE

ZCT

INPUT 2

LOAD

SOURCE

ZCT

INPUT 3

LOAD

SOURCE

ZCT

INPUT 4

LOAD

SOURCE

ZCT

WIRING INSTRUCTIONS

■SCREW TERMINAL

Torque: 0.5 N·m

■SOLDERLESS TERMINAL mm (inch)

Refer to the drawing below for recommended ring tongue

terminal size. Spade tongue type is also applicable. Solder-

less terminals with insulation sleeve do not ﬁt.

Applicable wire size: 0.3 – 0.75 mm2

3.2 (.13) dia.

4 min.

(.16)

12 (.47) max.

6 max.

(.24)

3 (.12) max.

Andere M-system E/A-System Handbücher

M-system

M-system R3-SV4A Bedienungsanleitung

M-system

M-system R7ML-LC2-R Bedienungsanleitung

M-system

M-system R3-SV8A Bedienungsanleitung

M-system

M-system Mini-MW Series Bedienungsanleitung

M-system

M-system R3S-DA16 Bedienungsanleitung

M-system

M-system R7L-EC16A Bedienungsanleitung

M-system

M-system R30YN16C Bedienungsanleitung

M-system

M-system R80DCT16A2 Bedienungsanleitung

M-system

M-system R7F4DD-DC16B-C Bedienungsanleitung

M-system

M-system R7 Series Bedienungsanleitung

M-system

M-system Devicenet R7F4DD-DA16A-C Bedienungsanleitung

M-system

M-system R7D-YS2A Bedienungsanleitung

M-system

M-system R7E-MS4 Bedienungsanleitung

M-system

M-system M5XPHS Bedienungsanleitung

M-system

M-system R5-SV Bedienungsanleitung

M-system

M-system R7I4DML3-DAC32C Bedienungsanleitung

M-system

M-system R7M-DC8C Bedienungsanleitung

M-system

M-system R5 Series Bedienungsanleitung

M-system

M-system R7E-PA8 Bedienungsanleitung

M-system

M-system R3-SV8N Bedienungsanleitung

M-system

M-system R7E-EC8B Bedienungsanleitung

M-system

M-system R8-CT4E Bedienungsanleitung

M-system

M-system R3-CT8C Bedienungsanleitung

M-system

M-system R3-AS8 Bedienungsanleitung

Beliebte E/A-System Handbücher anderer Marken

WAGO

WAGO 750-344 Bedienungsanleitung

Teknim

Teknim TWM-1887 Bedienungsanleitung

Intelligent Appliance

Intelligent Appliance IA-2662-E Bedienungsanleitung

BERGHOF

BERGHOF ECC DIO 16/16 Bedienungsanleitung

Advantech

Advantech PCM-27J3AU Installations- und Betriebshandbuch

Festo

Festo CP-E08-M12-CL Bedienungsanleitung

Measurement Computing

Measurement Computing PCI-DAS64/M1/16 Bedienungsanleitung

Hitachi

Hitachi HX-RIO3 Series Bedienungsanleitung

NUUO

NUUO SCB-A08 Bedienungsanleitung

jablotron

jablotron JB-110N Bedienungsanleitung

Omron

Omron SYSMAC C200H Bedienungsanleitung

DOLD

DOLD SAFEMASTER M Bedienungsanleitung

ABB

ABB OPT-MF-001 Bedienungsanleitung

Omron

Omron SYSMAC C2000H Bedienungsanleitung

Helmholz

Helmholz TB20 Bedienungsanleitung

ICP DAS USA

ICP DAS USA tM-AD2 Bedienungsanleitung

Automationdirect.com

Automationdirect.com DL305 Bedienungsanleitung

WAGO

WAGO I/O-SYSTEM 750 Bedienungsanleitung