Mazda 0000-8C-Z02 Bedienungsanleitung

GENUINE ACCESSORIES

INSTALLATION INSTRUCTIONS

PART NUMBERS: APPLICABLE MODELS:

0000-8C-Z02 Electrochromic Mirror w/ Compass/ HomeLink® 2006 >Mazda3

0000-8C-L07 Compass / HomeLink® Installation Kit (non-rain sensor models)

REQUIRED COMPONENTS:

ITEM QTY DESCRIPTION SERVICE PART NUMBER

1 1 Mirror Assembly with Compass 0000-8C-Z02

INSTALLATION KIT COMPONENTS:

2 1 Harness Assembly – Power and Ground 0000-8C-H12

3 2 Wire Tap 000-8C-H09

4 4 Tie Wrap (Short) --

5 1 Wire Cover 000-8C-H11

6 1 Installation Instructions --

7 1 User Guide --

HOMELINK®AND THE HOMELINK HOUSE®ARE REGISTERED TRADEMARKS OF JOHNSON CONTROLS, INC.

TOOLS REQUIRED:

Clean Rag Wire Cutters Ratchet

Fiberstick Electrical Tape 10mm Socket

Pliers #T20 Torx 4mm Flat Screwdriver

Page 1 of 8 Revision A 550-0336

INSTALLATION PRECAUTIONS / NOTES:INSTALLATION PRECAUTIONS / NOTES:

•Do not use excessive force when removing OE mirror from windshield.•Do not use excessive force when removing OE mirror from windshield.

•Do not place wire harness against objects with sharp edges that may cause electrical

shorting.

•Do not place wire harness against objects with sharp edges that may cause electrical

shorting.

•On vehicles equipped with “A” pillar air bag, verify mirror harness path remains clear of

air bag. Harness should follow, and be tied to existing OEM wiring with tie wraps.

•On vehicles equipped with “A” pillar air bag, verify mirror harness path remains clear of

air bag. Harness should follow, and be tied to existing OEM wiring with tie wraps.

•Verify that power harness path will not interfere with brake, clutch, emergency brake or

air bag operation. Use tie wraps to hold the wiring away from critical locations.

•Verify that power harness path will not interfere with brake, clutch, emergency brake or

air bag operation. Use tie wraps to hold the wiring away from critical locations.

rform the following pre-installation steps:

PP . Place kit components on a clean, padded

surface and inspect for damage or defects.

2. Record customer’s programmed radio stations (if

applicable).

1. Disconnect negative battery terminal.

a) Remove relay cover by grasping rear of

cover and pulling upwards. Disengage the

locking tab at the front of cover. (Fig. 1-1)

b) Remove two (2) 10mm bolts from

battery cover. Disengage locking tabs and

remove cover. (Fig. 1-2)

c) Disconnect negative battery terminal.

2. Remove driver-side scuff plate.r-side scuff plate.

a) Use fiberstick to disengage clips. (Fig. 1-3)a) Use fiberstick to disengage clips. (Fig. 1-3)

1 Preparation

Fig. 1-1

Fig. 1-2

10mm Bolts

Fig. 1-3

Page 2 of 8 Revision A 550-0336

3. Remove driver-side kick plate.

a) Use 4mm screwdriver to release center

of plastic push-pin.

b) Grasp kick plate at rear and pull out

towards passenger-side of vehicle.

(Fig. 1-4)

4. Loosen driver-side door seal past top

of A-pillar. (Fig. 1-5)

5. Remove A-pillar trim.

a) Pull out top of A-pillar trim towards

passenger-side of vehicle until A-pillar push-pin

connector is fully extended. (Fig. 1-6)

b) Pull A-pillar trim towards the rear of the

vehicle to release the base and to slide upwards

and off from A-pillar push-pin connector.

(Fig. 1-6)

6. Remove OE mirror.

a) Insert fiberstick between bottom of mirror mount

and windshield glass. (Fig. 1-7)

b) Push fiberstick up into mount to disengage

locking tab. Pull up while gently wiggling mirror

to remove.

Push-pin

Fig. 1-4

Fig. 1-5

CAUTION

A-pillar

Push-pin

Connector

Fig. 1-6

CAUTION

Do not use excessive force.

-pillar connector could be damaged.

Fig. 1-7

Page 3 of 8 Revision A 550-0336

1. Plug 10-pin connector into back of EC mirror.

(Fig. 2-1)

2. Attach EC mirror.

a) Hold the mirror head and slide the mount

downwards as far as possible over the windshield

button, until fully seated.

b) Using a #T20 Torx, tighten the mirror mounting

bracket screw to 1.3 ft-lbs (17.8 kg-cm).

(Fig. 2-2)

Fig. 2-1

2 EC Mirror Installation

NOTE

1. Route EC harness from mirror to headliner.

a) Route power harness into groove of wire

cover and attach wire cover to mirror base.

(Fig. 3-1)

b) Slide upper portion of wire cover up to headliner

so the “forks” are held by the headliner.

(Fig. 3-1)

2. Route EC harness to driver-side A-pillar.

a) Route power harness between vehicle headliner

and roof to top of driver-side A-pillar area.

(Fig. 3-2)

3 Route EC Mirror Harness to Vehicle Power

Fig. 3-2

1.3 ft-lbs

Fig. 2-2

Fig. 3-1

Slide harness sleeve as close to mirror connector as

ossible.

Page 4 of 8 Revision A 550-0336

3. Route EC harness down driver-side A-pillar.

a) Route power harness along factory harness in

driver-side A-pillar. (Fig. 3-3)

b) Secure power harness to factory harness with

three (3) tie wraps. (Fig. 3-3)

c) Cut excess material off tie wraps.

4. Route power harness to driver-side kick-plate area.

a) Route power harness through driver-side

instrument panel and into kick-plate area.

(Fig. 3-4)

1. Attach wire tap connectors to B+ and +12V ignition.

a) Locate the wire bundle in the driver-side kick

plate area. (Fig. 4-1)

b) Remove electrical tape wrapping as required

to access wires.

c) Locate Orange / Black-stripe wire (B+) in the

kick plate wire bundle.

d) Using pliers, secure wire tap to

Orange / Black-stripe wire. (Fig. 4-2)

e) Locate the Orange / Yellow-stripe wire (+12V)

in the bundle.

f) Using pliers, secure wire tap to

the Orange / Yellow-stripe wire. (Fig. 4-2)

Fig. 4-2

Fig. 3-4

Fig. 3-3

CAUTION

Tie

Wraps

CAUTION

Verify mirror harness path is clear of air bag (if equipped).

CAUTION

Do not tie wrap harness to sunroof drain tube (if equipped).

4 Connect Harness Power and Ground

Fig. 4-1

Remove

Tape

Orange /

Black-stripe

Wire

Orange /

Yellow-stripe

Wire

Page 5 of 8 Revision A 550-0336

Fig. 4-3

2. Connect EC power harness to ground.

a) Locate 10mm ground bolt, upper left of wire

bundle in driver-side kick-plate area. (Fig. 4-3)

b) Using 10mm socket, remove bolt.

c) Place ground ring from EC power harness, over

bolt and re-install bolt. (Fig. 4-3)

d) Tighten bolt to 80-90 in. lbs.

3. Connect EC power harness to B+ wire tap.

Ground

Wire

Fig. 4-4

Black /

White-stripe

Orange /

Yellow-stripe

Solid Black

Orange /

Black-stripe

a) Insert male spade terminal of solid black

harness wire into opening of wire tap on the

Orange / Black-stripe wire. (Fig. 4-4)

4. Connect EC power harness to +12V ignition.

a) Insert male spade terminal of black / white-stripe

harness wire into opening of wire tap on

the Orange / Yellow-stripe wire. (Fig. 4-4)

1. Bundle excess power harness and secure.

a) Bundle any excess power harness wires.

b) Secure bundled harness wires to factory wire

bundle with one (1) tie wrap. (Fig. 5-1)

1. Reconnect negative battery cable.

2. Turn the ignition switch ON/ACC position.

3. With the vehicle in a fairly well-lit area, perform the

following:

a) To make sure the auto-dimming feature is on,

verify that the green LED to the left of the

center switch is on. If it is not on, push the

switch to turn the green LED on.

b) Cover the forward looking photocell on the

back of mirror with a dark cloth or towel.

(Fig. 6-1)

NOTE

Fig. 5-1

Ensu

e male s

ade connectors are full

inserted into wire ta

5 maining Harness WiresSecure Re

Tie Wrap

6 Testing

Dark Cloth or Towel

Rearward

Photocell

Green LED

Compass

Display Window

Fig. 6-1

Page 6 of 8 Revision A 550-0336

In a few seconds, the mirror will

begin to darken.

c) Remove the cover from the forward looking

photo cell and the mirror will begin to clear.

d) Verify that either a direction, such as NE, or

“C” is displayed in the display window. If not,

ensure the feature is turned ON by pressing the

button.

4. Turn the ignition key to the OFF position.

5. Push each HomeLink® button, one at a time, and

NOTE

verify that LED indicator to the left of the center

switch illuminates with a red LED. (Fig. 6-2)

6. Testing is now complete.

1. Trim excess off all wire ties.

2. Reinstall in reverse order, all trim pieces removed

during installation.

3. Place User Guide in vehicle glove-box.

(Fig. 7-1)

4. Remove fingerprints, smudges, dirt, etc. from mirror.

5. Verify each reinstalled component for proper fit and

function.

1. Adjust compass zone after EC mirror installation.

a) The zone setting is factory preset to Zone 8.

Refer to Compass Calibration Zone Map

(Fig. 8-1) to find correct compass zone setting

for your geographical location. Use same map

from User Guide.

b) To change the zone setting, push and hold the

right button until a number appears in the display.

Press button repeatedly until desired compass

zone number is reached.

Time to darken will var

with ambient li

ht level.

Red LED

HomeLink Buttons

Fig. 6-2

7 Installation of Removed Components

Fig. 7-1

User Guide

8 Compass Zone Adjustment (Dealer Install ONLY)

678

678910 11 12 13

Fig. 8-1

Page 7 of 8 Revision A 550-0336

1. Calibrate compass.

a) Drive to an open, level area, away from large

metallic objects or structures.

b) Hold the right button for approximately 9 seconds

until “C” text appears in the display. Release

the right button to enter the calibration mode.

c) Drive slowly in up to 3 circles until the “C”

disappears, and a directional heading is

displayed. The compass is now calibrated.

9 Compass Calibration (Dealer Install ONLY)

Page 8 of 8 Revision A 550-0336

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Mazda Autozubehör Handbücher

Mazda

Mazda 0000-8G-N03 Bedienungsanleitung

Mazda

Mazda KMV6V7210 Bedienungsanleitung

Mazda

Mazda 0000-8L-G03A Bedienungsanleitung

Mazda

Mazda 0000-8K-L05 Bedienungsanleitung

Mazda

Mazda GENUINE SIDE UNDER SPOILER Bedienungsanleitung

Mazda

Mazda GENUINE ACCESSORIES Bedienungsanleitung

Mazda

Mazda CX-5 Bedienungsanleitung

Mazda

Mazda KPF1 V3 460 Leitfaden

Mazda

Mazda CX-9 Bedienungsanleitung

Mazda

Mazda C830-V7-050A Bedienungsanleitung

Mazda

Mazda A2DP Bedienungsanleitung

Mazda

Mazda Connect Bedienungsanleitung

Mazda

Mazda 0000-8G-K02 Bedienungsanleitung

Mazda

Mazda CX-3 Bedienungsanleitung

Mazda

Mazda 0000 8C Z01 Bedienungsanleitung

Mazda

Mazda DN4J-V7-055 Bedienungsanleitung

Mazda

Mazda 0000-8G-K05 Bedienungsanleitung

Mazda

Mazda 0000-8G-L12 Bedienungsanleitung

Mazda

Mazda 6 GJ 2.2 D 2012 Bedienungsanleitung

Mazda

Mazda Connect Bedienungsanleitung

Mazda

Mazda DN4J-V7-110 Bedienungsanleitung

Mazda

Mazda 0000-8E-R10 Bedienungsanleitung

Mazda

Mazda PROTEGE 5 Bedienungsanleitung

Mazda

Mazda 0000 81 L25 Bedienungsanleitung

Beliebte Autozubehör Handbücher anderer Marken

James Baroud

James Baroud Odyssey Bedienungsanleitung

Motorola

Motorola i50sx Bedienungsanleitung

Yakima

Yakima 9MM STANDARD BIKE MOUNT Bedienungsanleitung

Feniex

Feniex T3 Bedienungsanleitung

Kia

Kia E8300-4D000 Bedienungsanleitung

Brink

Brink 756843 Bedienungsanleitung

Whispbar

Whispbar K085W Bedienungsanleitung

v.link

v.link CI-VL2-PC-HSD Bedienungsanleitung

Viking

Viking Stack-Rack Kurzanleitung zur Einrichtung

Aries

Aries 203015 Bedienungsanleitung

Choetech

Choetech AT0005 Bedienungsanleitung

ZZ2

ZZ2 ZZAIR-PRO Bedienungsanleitung

Holman

Holman 4A80L Bedienungsanleitung

Thule

Thule 2075 Bedienungsanleitung

Motorola

Motorola T325 Bedienungsanleitung

TAUBENREUTHER

TAUBENREUTHER 16-3950 Installationsanleitung

DV8

DV8 FBJL-02 Bedienungsanleitung

Prorack

Prorack K1163 Bedienungsanleitung