Metra Electronics 99-7392B Bedienungsanleitung
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 6/21/19 INST99-7392B
INSTALLATION INSTRUCTIONS
99-7392B
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT COMPONENTS
• A) Radio housing (front) • B) Radio housing (rear) • C) Radio brackets • D) Pioneer adapter brackets • E) Pocket • F) (4) #4 x 3/8” Phillips screws
• G) (6) #8 x 3/8” Phillips screws • H) Panel clip
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Preparation .......................................................3
Kit Assembly
–ISO DIN radio provision with pocket...................4
–ISO DDIN radio provision......................................5
–Pioneer modular DDIN radio provision ......... 6-7
WIRING & ANTENNA CONNECTIONS
(sold separately)
Wiring harness: 70-7306
Antenna adapter: 40-KI11
Steering wheel control interface: ASWC-1
12v to 6v camera step-down: AX-CAM6V
A B C D E
FGH
Hyundai Kona 2018-up
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision †
• Pioneer modular DDIN radio provision †
• Painted matte black
† This kit can only be used with an ISO DDIN radio with an “L” shaped chassis design, with the radio
chassis at the bottom of the screen. As of this writing, only the Alpine INE-W967HD (discontinued,
replaced by INE-W977HD), iLX-107, and iLX-207 have this design. Also, The Pioneer modular radios,
DMH-C2550NEX and DMH-C2500NEX, can also be used with the included adapter brackets.
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
1.800.221.0932
|
MetraOnline.com
2
DASH DISASSEMBLY
1. Unclip and remove the speedometer
cluster bezel, and the top trim from the
steering column. These will come out
as one piece, connected by material.
(Figure A)
2. Unclip and remove the entire panel that
houses the center and right a/c vent.
(Figure B)
Continue to Kit Preparation
(Figure A) (Figure B)
REV. 6/21/2019 INST99-7392B 3
KIT PREPARATION
1. Remove the top trim piece behind
the radio:
a. Unclip the (3) clips securing the
front of the trim. (Figure A)
b. Slide the trim to the left, then up
and slightly back to release the
trim. A little finesse is required with
this process. (See inset)
2. Remove (2) Phillips screws securing the
back of the radio. (Figure B)
3. Remove (2) Phillips screws securing the
bottom of the radio. Take note that the
radio brackets are angled inward, hiding
the screws from being easily seen. Slide
the radio out, then unplug and remove
the radio. (Figure C)
Continue to Kit Assembly
(Figure A) (Figure B) (Figure C)
Bottom side of trim panel
1.800.221.0932
|
MetraOnline.com
4
KIT ASSEMBLY
ISO DIN radio provision with pocket
1. Secure the
radio brackets
to the
pocket
using (2) #8 x 3/8” Phillips screws
provided. (Figure A)
2. Attach the
panel clip
provided onto the
radio housing (front)
.
3. Secure the bracket/pocket assembly to
the
radio housing (front)
using (4) #8 x
3/8” Phillips screws provided. (Figure B)
4. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
5. Slide the radio into the bracket/housing/
pocket assembly from the back, then
secure it to the assembly using the
screws supplied with the radio.
(Figure C)
(Figure B) (Figure D)
(Figure C)(Figure A)
6. Secure the
radio housing (rear)
to the
radio assembly using (4) #4 x 3/8”
Phillips screws provided. (Figure D)
7. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using
the proper mating adapter from Metra
and/or Axxess. Test the radio for proper
operation.
8. Secure the radio assembly to the dash
using the (4) factory screws.
9. Reassemble the dash in reverse
order of disassembly to complete the
installation.
REV. 6/21/2019 INST99-7392B 5
KIT ASSEMBLY
ISO DDIN radio provision
1. Attach the
panel clip
provided onto the
radio housing (front)
.
2. Secure the
radio brackets
to the
radio
housing (front)
using (4) #8 x 3/8”
Phillips screws provided. (Figure A)
3. Slide the radio into the bracket/housing
assembly from the back, then secure
it to the assembly using the screws
supplied with the radio. (Figure B)
4. Secure the
radio housing (rear)
to the
radio assembly using (4) #4 x 3/8”
Phillips screws provided. (Figure C)
(Figure B)
(Figure C)(Figure A)
5. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra
and/or Axxess. Test the radio for
proper operation.
6. Secure the radio assembly to the dash
using the (4) factory screws.
7. Reassemble the dash in reverse
order of disassembly to complete the
installation.
1.800.221.0932
|
MetraOnline.com
6
Pioneer Modular DDIN radio provision
Note: For steps 3 and 4, reference the
installation manual provided with the
radio for which hardware to use. The
display screen and radio chassis use two
different types of screws.
1. Attach the
panel clip
provided onto the
radio housing (front)
.
2. Secure the
radio brackets
to the
radio
housing (front)
using (4) #8 x 3/8”
Phillips screws provided. (Figure A)
3. Secure the radio display to the
Pioneer
adapter brackets
using (6) screws
supplied with the radio. (Figure B)
(Figure B)
(Figure C)(Figure A)
4. Secure the display/bracket assembly
to the radio chassis using (4) screws
supplied with the radio. (Figure C)
5. Slide the radio assembly into the
bracket/housing assembly from the
back, then secure it to the assembly
using the screws supplied with the
radio. (Figure D)
Continued on the next page
KIT ASSEMBLY
(Figure D)
REV. 6/21/2019 INST99-7392B 7
6. Secure the radio housing (rear) to the
radio assembly using (4) #4 x 3/8”
Phillips screws provided. (Figure E)
7. Locate the factory wiring harness and
antenna connector in the dash and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra
and/or Axxess. Test the radio for
proper operation.
8. Secure the radio assembly to the dash
using the (4) factory screws.
9.
Reassemble the dash in reverse order of
disassembly to complete the installation
.
KIT ASSEMBLY (CONT.)
(Figure E)
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 6/21/19 INST99-7392B
INSTALLATION INSTRUCTIONS
99-7392B
If you are having difficulties with the installation
of this product, contact our Tech Support line
either by phone at 1-800-253-TECH, or email at
techsupport@metra-autosound.com. Before
doing so, look over the instruction booklet a
second time and ensure that the installation was
performed exactly as the instruction booklet
is stated. Have the vehicle apart and ready to
perform troubleshooting steps before contacting
Metra/Axxess Tech Support.
Inhaltsverzeichnis
Andere Metra Electronics Autozubehör Handbücher
Metra Electronics
Metra Electronics 99-5816 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-7318 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7579 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7953 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-4000 Bedienungsanleitung
Metra Electronics
Metra Electronics CADILLAC 95-2004 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-3527 Bedienungsanleitung
Metra Electronics
Metra Electronics LEXUS 99-8150 Bedienungsanleitung
Metra Electronics
Metra Electronics 71-7552 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-7801 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7356B Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7319 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7503 Bedienungsanleitung
Metra Electronics
Metra Electronics 98-9306 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-8712 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7414 Bedienungsanleitung
Metra Electronics
Metra Electronics 71-6522 Bedienungsanleitung
Metra Electronics
Metra Electronics 95-7325 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-5801 Bedienungsanleitung
Metra Electronics
Metra Electronics 99-7950 Bedienungsanleitung
