Milwaukee CD97 Bedienungsanleitung

USER MANUAL

CD97

Digital

Low Range TDS Pen

SPECIFICATIONS

RANGE 0 to 999 ppm

RESOLUTION 1 ppm

ACCURACY

(@20°C) ±10 ppm

TYPICAL

EMC DEVIATION ± 1 % Full Scale

TEMPERATURE

COMPENSATION

Automatic from

5 to 50ºC

ENVIRONMENT 5 to 50°C

95 % RH max.

BATTERY TYPE 4 x 1.5V alkaline

BATTERY LIFE

approximately

300hours of use

DIMENSIONS 150 x 30 x 24 mm

WEIGHT 85 g

OPTIONAL ACCESSORIES

MA9300 1.5V battery (10pcs.)

MA9701 Calibration Screwdrivers

(20pcs)

M10080B

Calibration 20mL sachet

800ppm solution

(25pcs.)

Milwaukee Instruments reserves the

right to make improvements in design,

construction and appearance of its

products without advance notice.

CERTIFICATION

Milwaukee Instruments

conform to the CEEuropean

Directives.

Disposal of Electrical &

Electronic Equipment. Do

not treat this product as household

waste. Hand it over to the appropriate

collection point for the recycling of

electrical and electronic equipment.

Disposal of waste

batteries. This product

contains batteries. Do not

dispose of them with other household

waste. Hand them over to the appropriate

collection point for recycling.

Please note: proper product and

battery disposal prevents potential

negative consequences for human

health and the environment. For

detailed information, contact your local

household waste disposal service or go to

www.milwaukeeinstruments.com (USA

& CAN) or www.milwaukeeinst.com.

WARRANTY

This instrument is warranted against

defects in materials and manufacturing

for a period of 2 years from the date

of purchase. Probe is warranted for

6 months. This warranty is limited to

repair or free of charge replacement if the

instrument cannot be repaired. Damage

due to accidents, misuse, tampering

or lack of prescribed maintenance is

not covered by warranty. If service is

required, contact your local Milwaukee

Instruments Technical Service. If the

repair is not covered by the warranty, you

will be notified of the charges incurred.

When shipping any instrument, make

sure it is properly packaged for complete

protection.

ISTCD97 11/20

SATISFACTION

GUARANTEED

888

CD97

Distributor in AustraliaPacific Sensor Technologies Pty LtdUnit 4, 3 Neutron Place Rowville, VIC 3178 Australia1300 662 720 | [email protected]www.pacificsensortech.com.au

888

CD97

RANGE

0 / 999

ppm

FRONT

ON/OFF

SWITCH

LIQUID

CRYSTAL

DISPLAY

MAXIMUM

IMMERSION

LEVEL

MINIMUM

IMMERSION

LEVEL

SENSING

PROBES

BATTERY

COMPARTMENT

CALIBRATION

TRIMMER

POCKET

CLIP

BACK

OPERATION

yRemove the protective cap.

yTurn the digital pen on with the

ON/OFF switch located on the top.

000

CD97

yImmerse into solution up to the

maximum immersion level.

yStir gently and wait until the display

stabilizes. CD97 compensates for the

temperature variance automatically.

yRead the value on the display.

CALIBRATION

yThe calibration procedure is very

simple and fast.

yImmerse the pen up to the maximum

level into the appropriate optional

Calibration Solution M10080B

correspondig to 800ppm.

yAllow the reading to stabilize.

yBy turning the calibration trimmer

with a small screwdriver adjust the

reading to match the solution value

of 800ppm (normally to the value at

25°C).

800

600

yCalibration is now complete.

BATTERY REPLACEMENT

When the CD97 cannot be switched

on or the display fades, pull out the

battery compartment and replace all

four 1.5V batteries, paying attention

to their polarity. Batteries should only

be replaced in a non‑hazardous area

using the battery types specified in this

instruction manual.

CD97

RECOMMENDATION

Before using this product, makesure that

it is entirely suitable for the environment

in which they are used. Operation of

these instruments in residential areas

could cause unacceptable interferences

to radio and T.V. equipment. The pins at

the end of the sensor are sensitive to

electrostatic discharges. Avoid touching

this metal band at all times. During

operation of instruments ESD wrist

straps should be worn to avoid possible

damage to the sensor by electrostatic

discharge. Any variation introduced

by the user to the supplied equipment

may degrade the instrument EMC

performance. To avoid electrical shock,

do not use the instrument when voltage

at the measurement surface exceed

24VAC or 60VDC. To avoid damages or

burns, do not perform any measurement

in microwave ovens.

Andere Milwaukee Messgerät Handbücher

Milwaukee

Milwaukee MW11 Bedienungsanleitung

Milwaukee

Milwaukee MW102 Bedienungsanleitung

Milwaukee

Milwaukee MA887 Bedienungsanleitung

Milwaukee

Milwaukee MI 411 Bedienungsanleitung

Milwaukee

Milwaukee 3421 Bedienungsanleitung

Milwaukee

Milwaukee MI 413 Bedienungsanleitung

Milwaukee

Milwaukee SM101 Bedienungsanleitung

Milwaukee

Milwaukee 2217-40 Bedienungsanleitung

Milwaukee

Milwaukee MW700 Bedienungsanleitung

Milwaukee

Milwaukee MR32ATC Bedienungsanleitung

Milwaukee

Milwaukee 2235-40 Bedienungsanleitung

Milwaukee

Milwaukee LDM 45 Bedienungsanleitung

Milwaukee

Milwaukee MW14 Bedienungsanleitung

Milwaukee

Milwaukee MA886 Bedienungsanleitung

Milwaukee

Milwaukee M12 CPL Bedienungsanleitung

Milwaukee

Milwaukee MW102 Bedienungsanleitung

Milwaukee

Milwaukee 2280-20 Bedienungsanleitung

Milwaukee

Milwaukee pH51 Bedienungsanleitung

Milwaukee

Milwaukee MW306 MAX Bedienungsanleitung

Milwaukee

Milwaukee CALIBRATION 2238-20 Bedienungsanleitung

Milwaukee

Milwaukee MC510 Bedienungsanleitung

Milwaukee

Milwaukee MI 406 Bedienungsanleitung

Milwaukee

Milwaukee M12 3PLA Bedienungsanleitung

Milwaukee

Milwaukee MI 405 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung