Morphy Richards Ultralight bagless vacuum cleaner Bedienungsanleitung

www.morphyrichards.com

Ultralight bagless vacuum cleaner

Please read and keep these

instructions

getting the best from

your new cleaner...

If your cleaner isn’t picking up as well as it should,

please check

• Dust canister

It is important to regularly empty the canister even if it does not

appear full.

• Filters

It is important that the pleated filter is shaken clean each time

the dust canister is emptied to allow air through the appliance.

Wash the canister filters regularly in warm water and allow to

air dry. A spare pleated filter is included.

• Blockages

Check the hose, tubes and tools for blockages

• Belt

Check and replace damaged or broken belt

• Height adjustment

The height adjustment only comes into effect when the handle is

released by the handle release pedal È.

73322 Rev 2 17/1/05 2:42 PM Page 1

Important safety

instructions

The use of any electrical appliance

requires the following of common sense

safety rules.

Primarily there is danger of personal

injury and secondly danger of damage to the

appliance and property. These are indicated

in the instructions text by the following two

conventions:

WARNING: Danger of personal injury

IMPORTANT: Damage to the appliance

In addition we offer the following

essential safety advice.

Location

•Do not use or keep this product outside

when it is raining.

•Do not store the appliance near hot

ovens or heating appliances.

Mains lead

•Do not allow the mains lead to become

strained or run this appliance over it.

•If the electrical cable becomes damaged

the complete cable assembly must be

replaced. Do not attempt this task

yourself, contact Morphy Richards using

the helpline number.

Children

•Children do not understand the dangers

associated with operating electrical

appliances. Never allow children to use

this appliance.

Other safety considerations

•Never use in the presence of explosive

liquids or vapours.

•Never pick up inflammable or poisonous

liquids such as petrol, copier toner, or

other volatile substances. Never pick up

acids, asbestos or asbestos dust.

•Never use the appliance without the

filters installed.

•Never use the appliance to vacuum hot

ashes, broken glass, sharp objects or

liquids.

•Never modify the cleaner in any way.

•Always disconnect the appliance from the

mains supply after use or prior to

cleaning or emptying.

•The appliance should never be left

running unsupervised.

•Repairs to electrical appliances are only

to be undertaken by trained personnel.

Unprofessional repairs can be dangerous

for users.

•Use only genuine Morphy Richards spare

parts and accessories

•Never over-extend the hose such that the

cleaner is pulled over. If the cleaner is

knocked over, switch off before

attempting to upright.

•Never pick the cleaner up by the floor

nozzle when connected to the mains, use

the carrying handle.

•WARNING: Keep loose clothing, hair,

fingers etc. away from the floor

nozzle whenever the cleaner is

connected to the mains.

•Disconnect from the mains supply before

attempting to clear blockages, clear the

brush or replace the belt.

Electrical

requirements

Check that the voltage on the rating plate

of your appliance corresponds with your

house electricity supply which must be A.C.

(Alternating Current).

If the socket outlets in your home are not

suitable for the plug supplied with this

appliance, the plug should be removed and

the appropriate one fitted.

WARNING: The plug removed from

the mains lead, if severed, must be

destroyed as a plug with bared flexible

cord is hazardous if engaged into a live

socket outlet.

Should the fuse in the 13 amp plug

require replacement, a BS1362 13 amp fuse

must be fitted.

73322 Rev 2 17/1/05 2:42 PM Page 2

Features

⁄Vari power slider (certain models only)

¤Front cover release

‹Removable front cover

›Exhaust filter grille

ﬁCarpet height adjustment knob

ﬂFloor nozzle with powered brush

‡Upper handle

·Flexible hose

‚Cord storage with quick release cleat

„On/Off switch

‰Carrying handle

ÂNested extension tubes (2)

ÊCrevice nozzle

ÁFurniture brush

ËHose clip slot

ÈHandle release pedal

ÍHose connector

ÎDust canister release (shown page 5)

ÏDust canister lid

ÌPleated circular filter

ÓDust canister

ÔCentral mesh filter

Canister handle

ÒMotor protection filter (shown page 6)

ÚExhaust filter (page 6)

ÛBelt cover (shown page 7)

ÙBrush bar (page 7)

ıMotor shaft (shown page 7)

ˆBrush bar end caps (shown page 7)

˜Hose clip

¯Turbo nozzle

Accessories included Extension tubes

Crevice tool

Furniture brush

‡

ﬁ

›

ﬂ

‹

‚

‰

„

⁄

Ó

73322 Rev 2 17/1/05 2:42 PM Page 3

Assembly

WARNING: Do not plug in the cleaner

until it is assembled.

1Carefully unpack all components.

2Lift cleaner body to upright position.

3Remove the two screws that are already

attached to the body.

4From the rear of the cleaner, align the

handle with groove and slide into the

body. If necessary, use thumb and finger

pressure to slide handle into position.

5Fasten the handle with the two screws.

Floor nozzle height

adjustment

Before using the cleaner the floor nozzle

height must be set to the correct height.

Choose the setting which most closely

matches your floor surface.

•Use the DEEP CARPET setting when

using the tools.

Note: The height adjustment only comes

into effect when the handle is released by

the handle release pedal È.

Variable power

(Certain models only)

Slide the variable power control to the

right to increase the suction power or to the

left to decrease suction. This feature is most

useful when using the hose and accessories.

Use the minimum setting when vacuuming

delicate fabrics/curtains etc. When not using

the hose it is advisable to keep the variable

slider set to maximum.

Using on carpets

1Place cleaner in its upright position.

2Set the carpet height adjustment knob to

the desired position.

3Release the mains cable by revolving the

quick release cleat 1/2a turn and extend

the cable fully.

4Plug the cable into the mains socket.

5Step on the handle release pedal to

release the handle to the desired

position.

6Press the on/off button to the ‘on’

position.

IMPORTANT: To prevent damage to

carpets, never leave the cleaner switched on

in one place for an extended period.

•Never have the brushes set too low such

that the cleaner is hard to push.

Using attachments

Follow steps 1-4 (using on carpets) but

set the carpet height adjustment knob to

deep carpet setting.

5Remove the hose connector Ífrom the

rear of the cleaner. Lift the hose ·from

the top handle hook. Insert the hose clip

˜into the hose clip slot Ë.

DEEP CARPET HARD FLOOR

MEDIUM CARPET

TOOLS

min max

73322 Rev 2 17/1/05 2:42 PM Page 4

•Push the required attachment firmly onto

the end of the hose.

•If additional length is required, attach one

or both extension tubes.

6Switch on/off.

•IMPORTANT: Always fix the hose clip ˜

to the main body slot Ëwhen using the

hose and tools.

•Never over extend the hose such that the

cleaner is pulled over.

IMPORTANT: Turning the cleaner

sideways helps prevent the cleaner being

pulled along by the stretch hose.

Using & cleaning turbo nozzle

Attach the turbo nozzle to the hose end

for use on upholstery and stairs.

After use your turbo nozzle may become

clogged. Turn over the nozzle and pull away

any hairs or fibres. If they are tightly wound

around the brush carefully snip the fibres

with scissors, being careful not to damage

the brush bar, pull away from the brush bar

and dispose.

Emptying

Empty the dust canister regularly even if

it does not look full this will maintain the

performance.

1Remove the front cover by lifting the

cover release lever. E

2Lift-up the dust canister release and pull

the canister away from the main body.

3Take the canister to the dustbin.

4Turn the lid 1/4turn anti-clockwise to

unlock, lift off the lid with pleated filter Ì,

put to one side. F

5Lift out the central mesh filter Ôfrom the

dust canister G. Brush clean if

necessary.

6Empty out the dust canister Ó.

7Re-fit the central mesh filter.

8Shake the pleated filter to remove all

dust.

9Re-fit pleated filter with lid into the dust

canister and turn lid 1/4turn clockwise to

lock.

10Re-fit dust canister into cleaner and push

to lock into position. Then re-fit front

cover.

Safety cut-out

If the cleaner overheats a motor

protection thermostat will automatically

switch the motor off. If this happens, switch

the cleaner off, unplug from the power

supply and leave the cleaner to cool for

at least 30 minutes. Check the airways for

blockages, empty dust canister and clean

the filters before restarting.



‹

73322 Rev 2 17/1/05 2:42 PM Page 5

Cleaning the filters

To maintain suction the pleated filter

must be shaken clean each time the

dust canister is emptied. Failure to clean

the filter will reduce suction and could

damage the motor if used for a prolonged

period. This may invalidate the guarantee. If

the filters become damaged they must be

replaced.

Pleated filter

This must be shaken clean at every

emptying to maintain suction. To thoroughly

clean it wash it regularly.

To remove it from the dust canister lid

turn the filter 1/4turn anti-clockwise. H

Wash in warm water (no detergent) and allow

to air dry before refitting. The spare pleated

filter allows one filter to be washed and dried

whilst the other is in use.

Motor protection filter

The motor protection filter Òis located

underneath the dust canister

1Remove the dust canister.

2Lift out the filter and shake over a

dustbin.

The filter may also be washed in water

(no detergents) but must be totally dry before

re-fitting.

3Replace the filter

Exhaust filter

The exhaust filter is located below the

dust canister compartment.

1Remove the front cover.

2Remove the exhaust filter Úby pulling

forward at the top and lift it away.

3Take the filter out of the cage and shake

vigorously over a dustbin. The filter may

also be washed in warm water. Do not

use detergents. The filter must be

completely dry before re-fitting. Allow

filters to air dry naturally.

4Replace the filter and front cover.

Changing the belt

If the brush bar stops rotating it is likely

that the drive belt has snapped (usually

because the brush has been stalled). A spare

belt is supplied. Replacement belts can also

be obtained from Morphy Richards.

Removing the floor nozzle

cover

1Disconnect the cleaner from the mains

supply.

73322 Rev 2 17/1/05 2:42 PM Page 6

2Press the handle release pedal and place

the cleaner face down, in the flat position

on a soft surface (eg carpet).

3Use a cross-head screwdriver to remove

the four screws indicated J.

4Turn the cleaner over.

5While pressing the handle release

pedal lift the rear of the top cover,

unhook from the front then completely

remove the cover K.

Replacing the belt

6Lift off the belt cover Û.

7Gently pull the right hand side (belt side)

of the floor nozzle outwards and at the

same time lift the brush bar out of its

location M.

8If the belt has broken, ensure all pieces

are removed. Clean the motor shaft ı.

9Check the brush bar end caps. ˆ

10 Fit the left hand end cap into the floor

nozzle.

11 Fit the right hand end cap onto the brush

bar.

12 Place one end of the new belt over the

motor shaft and the other around the

pulley end of the brush.

13 Locate the left hand side of the brush bar

first, then while pulling the right hand side

of the nozzle gently outwards and

stretching the belt, lower the right hand

side of the brush into its location.

14 Rotate the brush by hand to ensure it is

correctly and securely located.

15 IMPORTANT: Re-fit the belt cover.

16 Replace the top cover, hooking it in at the

front first and by pressing the handle

release pedal to allow the rear to

correctly locate N.

17 Turn the cleaner face down and re-fit and

tighten the four fixing screws, do not

overtighten.

18 Return the cleaner to its correct working

position before re-testing.

73322 Rev 2 17/1/05 2:42 PM Page 7

Your two-year

guarantee

•It is important to retain the retailers

receipt as proof of purchase. Staple

your receipt to this back cover for future

reference.

Please quote the following information if

the product develops a fault. These numbers

can be found on the base of the product.

Model no. Serial no.

All Morphy Richards Products are

individually tested before leaving the factory.

In the unlikely event of any appliance proving

to be faulty within 28 days of purchase it

should be returned to the place of purchase

for it to be replaced.

If the fault develops after 28 days and

within 24 months of original purchase, you

should contact the helpline number quoting

model number and serial number on the

product, or write to Morphy Richards at the

address shown. You will be asked to return

the product (in secure, adequate packaging)

along with a copy of proof of purchase.

Subject to the exclusions set out below (1-

6), the faulty appliance will then be repaired

or replaced and dispatched usually within

seven working days of receipt.

If for any reason this item is replaced

during the 2-year guarantee period, the

guarantee on the new item will be calculated

from original purchase date. Therefore it is

vital to retain your original receipt or invoice

to indicate the date of initial purchase.

To qualify for the two-year guarantee the

appliance must have been used according to

the manufacturers instructions. For example

the filters shall have been regularly cleaned

as instructed.

Morphy Richards shall not be liable to

replace or repair the goods under the terms

of the Guarantee where:

EXCLUSIONS

1The fault has been caused or is

attributable to accidental use, mis-use,

negligent use or used contrary to the

manufacturers recommendations or

where the fault has been caused by

power surges or damage caused in

transit.

2The appliance has been used on a

voltage supply other than that stamped

on the products.

3Repairs have been attempted by persons

other than our service staff (or authorised

dealer).

4Where the appliance has been used for

hire purposes or non-domestic use.

5Morphy Richards are not liable to carry

out any type of servicing work, under the

guarantee.

6Consumables such as the filters and belt

are not covered by the guarantee.

This guarantee does not confer any rights

other than those expressly set out above

and does not cover any claims for

consequential loss or damage. This

guarantee is offered as an additional benefit

and does not affect your statutory rights as a

consumer.

•This guarantee is valid in the UK and

Ireland only.

VC73322M UK Rev 2 01/05

The After Sales Division,

Registered address,

Morphy Richards Ltd, Mexborough,

South Yorkshire, England, S64 8AJ

Helpline (office hours)

UK 0870 060 2604

Republic of Ireland 1800 409119

Morphy Richards products are

intended for household use only

Morphy Richards has a policy of

continuous improvement in product

quality and design. The Company,

therefore, reserves the right to change

the specification of its models at any

time.

73322 Rev 2 17/1/05 2:42 PM Page 8

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Morphy Richards Staubsauger Handbücher

Morphy Richards

Morphy Richards Bagless Vacuum Cleaner Bedienungsanleitung

Morphy Richards

Morphy Richards CYCLONIC BAGLESS VACUUM CLEANER - REV 4 Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Bedienungsanleitung

Morphy Richards

Morphy Richards PerformAir Upright Vacuum Bedienungsanleitung

Morphy Richards

Morphy Richards VC73410 MUK Bedienungsanleitung

Morphy Richards

Morphy Richards IB70191 Bedienungsanleitung

Morphy Richards

Morphy Richards 73270 Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Deluxe Bedienungsanleitung

Morphy Richards

Morphy Richards IB73120 Bedienungsanleitung

Morphy Richards

Morphy Richards 73380 Bedienungsanleitung

Morphy Richards

Morphy Richards IB70045 Bedienungsanleitung

Morphy Richards

Morphy Richards IB73091 Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac Bedienungsanleitung

Morphy Richards

Morphy Richards IB73090 Bedienungsanleitung

Morphy Richards

Morphy Richards Supervac gold Bedienungsanleitung

Morphy Richards

Morphy Richards 73313 Bedienungsanleitung

Morphy Richards

Morphy Richards Storm 73215 Bedienungsanleitung

Morphy Richards

Morphy Richards Ecovac 70096 Bedienungsanleitung

Morphy Richards

Morphy Richards VORTICITY Bedienungsanleitung

Morphy Richards

Morphy Richards IB73100 Bedienungsanleitung

Morphy Richards

Morphy Richards Bagged cylinder Vacuum Bedienungsanleitung

Morphy Richards

Morphy Richards IB73190 Bedienungsanleitung

Morphy Richards

Morphy Richards ORB CYCLONE VACUUM CLEANER - REV 3 Bedienungsanleitung

Morphy Richards

Morphy Richards Pod vacuum cleaner Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung

Nobles

Nobles 608669 Produkthandbuch