Motic PA53MET Bedienungsanleitung

Motic PA53MET User Manual

Version 1.0.1

IMPORTANT NOTICE

This product may malfunction due to electromagnetic waves caused by portable personal telephone,

transceivers, radio-controlled toys, etc. Be sure to avoid having the above objects, which affect the

normal operation of the product, brought near the product. The information in this publication has been

carefully checked and is believed to be entirely accurate at the time of publication. MOTIC assumes no

responsibility, however, for possible errors or omissions, or for any consequences resulting from the use

of the information contained herein.

MOTIC reserves the right to make changes in its products or product specifications at any time and

without prior notices, and is not required to update this documentation to reflect such changes.

All rights are reserved.

Under copyright laws, this manual may not be copied, in whole or in part, without the prior written

consent of Motic China Group Co., Ltd.

CONTENTS

1. Safety Information 4

1.1 Introduction 4

1.2 Safety Symbols 5

1.3 Environment factors 6

1.4 Safety Precautions 7

2. Introduction 9

2.1 Indication for use (Intended use) 9

2.2 Classification 9

3. Operating Condition 10

4. Getting Ready 11

5. Maintenance and Storage 12

6. Nomenclature 13

7. Observation Procedure 16

7.1 Preparation 16

7.2 Procedure 16

8. Operation 18

8.1 Base 18

8.1.1 Voltage Indication and Switch 18

8.1.2 Turn ON/OFF Power saving function 18

8.1.3 Turn ON/OFF Intelligent Light function 19

8.1.4 Using the built-in Filters [PA53MET-T, PA53MET-BD-T] 19

8.2 Focusing Block 20

8.2.1 Replacing the Fine Adjustment Knob 20

8.2.2 Adjusting the Coarse Adjustment Knob Tension 20

8.2.3 Pre-focusing Lever 21

8.3 Stage 21

8.3.1 Rotating the Stage 21

8.4 Observation Tube 22

8.4.1 Adjusting the Interpupillar Distance 22

8.4.2 Adjusting the Diopter 22

8.4.3 Using the Eye Shades 23

8.4.4 Selecting the Light Path of the Trinocular Tube 23

8.5 Condenser [PA53MET-T, PA53MET-BD-T] 24

8.5.1 Centering the Condenser 24

8.5.2 Setting the Aperture Iris Diaphragm 25

8.6 Control pad [PA53MET-3D, PA53MET-BD-3D] 26

8.6.1 General function 26

8.6.2 Height display 26

8.6.3 Safety function 27

8.7 Linking Motic Analysis 27

8.7.1 Computer Control 27

9. Troubleshooting Guide 28

9.1 Electrical system 28

9.2 Optical system 28

9.3 Observation Tube 30

9.4 Stage and Focus Adjustment 30

10. Specifications 31

10.1 Body unit 31

10.2 3D module of PA53MET 32

10.3 Suitable Objectives 33

11. Assembly 34

11.1 Assembly Diagram 34

11.2 Detailed Assembly Procedures 35

11.2.1 Installing the Bulb 35

11.2.2 Attaching the Lamp housing 36

11.2.3 Attaching the Condenser [PA53MET-T, PA53MET-BD-T] 37

11.2.4 Attaching the Stage 37

11.2.5 Attaching the Observation Tube 38

11.2.6 Attaching the Eyepiece 38

11.2.7 Attaching the Control Box and Control Pad [PA53MET-3D, PA53MET-BD-3D] 39

11.2.8 Attaching the Computer 40

1. SAFETY INFORMATION

1.1 Introduction

Safety is everyone’s responsibility. The safe use of this equipment is largely dependent upon the

installer, user, operator, and maintainer. It is imperative that personnel study and become familiar with

this entire manual before attempting to install use, clean, service or adjust this equipment and any

associated accessories. It is paramount that the instructions contained in this manual are fully

understood and followed to enhance safety to the patient and the user/operator. It is for this reason that

the following safety notices have been placed appropriately within the text of this manual to highlight

safety related information or information requiring special emphasis. All users, operators, and

maintainers must be familiar with and pay particular attention to all Warnings and Cautions incorporated

herein.

WARNING

‘Warning” indicates the presence of a hazard that could result in severe personal injury, death or

substantial property damage if ignored.

CAUTION

“Caution” indicates the presence of a hazard that could result in minor injury, or property damaged if

ignored.

NOTE

“Note” describes information for the installation, operation, or maintenance of which is important but

hazard related if ignored.

1.2 Safety Symbols PA53MET Upright Compound Microscope

The International Electro technical Commission (IEC) has established a set of symbols. The symbols are

shown as below. This applies only to the instrument that has the certification symbol printed explicitly on

the product label or sticker.

I and O on power switch represent ON and OFF respectively.

This symbol identifies caution, risk of danger. Ensure you understand the function of this

control before using it. Control function is described in the appropriate User’s or Service

Manual.

This symbol identifies hot surface.

This symbol identifies the point where the system safety ground is fastened to the chassis.

Protective earth connected to conductive parts of Class I equipment for safety purposes.

This symbol identifies Alternating Current.

Disposal of your old appliance

When this crossed-out wheeled bin symbol is attached to a product it means the product is

covered by the European Directive 2002/96/EC.

All electrical and electronic products should be disposed of separately from the municipal

waste stream via designated collection facilities appointed by the government or the local

authorities.

The correct disposal of your old appliance will help prevent potential negative

consequences for the environment and human health.

For more detailed information about disposal of your old appliance, please contact your city

office, waste disposal service or the shop where you purchased the product.

1.3 Environment factors

Avoid the following environments for operation or storage:

●Where the equipment is exposed to water vapor. Don’t operate an equipment with a wet hand.

For indoor use only

●Where the equipment is exposed to direct sunlight.

●Where the temperature changes extremely

Normal operating temperature range is from 10°C to 40°C, Humidity is below 85%.

Altitude is from 700 to 1060hpa

●Where it is near the heat equipment.

●Where the equipment is subject to excessive shocks or vibrations.

●Where equipment is exposed to chemical material or explosive gas.

●Pull out the power cord with holding the plug, not the cord.

To avoid risk of electric shock, this equipment must only be connected to the supply mains with

protective earth.

Avoid places where the ambient temperature falls below 10°C or exceeds 40°C for normal operation, or

below -10°C or exceeds 55°C for transportation and storage. Humidity should be maintained below 95%

for normal operation, transportation and storage. The atmospheric pressure in operation, transportation

and storage is from 700 to 1060hpa.of Altitude up to 2,000m.

1.4 Safety Precautions

This equipment has been developed and tested according to safety standards as well as national and

international standards. This guarantees a very high degree of safety for this device. The legislator

expects us to inform the user expressively about the safety aspects in dealing with the device. The

correct handling of this equipment is imperative for its safe operation. Therefore, please read carefully all

instructions before switching on this device. For more detailed information, please contact our Customer

Service Department or one of our authorized representatives.

●This equipment must not be used (a) in an area that is in danger of explosions and (b) in the

presence of flammable, explosive, or volatile solvent such as alcohol, benzene or similar

chemicals.

●Do not put or use this device in humid rooms. Humidity should be maintained between 30 and 85%

for normal operation. Do not expose the device to water splashes, dripping water, or sprayed water.

Do not place containers containing fluids, liquids, or gases on top of any electrical equipment or

devices.

●The equipment must be operated only by, or under direct supervision of a properly trained and

qualified person.

●Modifications of this equipment may only be carried out by MOTIC’s service technicians or other

authorized persons.

●Customer maintenance of this equipment may only be performed as stated in the User’s Manual

and Service Manual. Any additional maintenance may only be performed by MOTIC’s service

technicians or other authorized persons.

●The manufacturer is only responsible for effects on safety, reliability, and performance of this

equipment when the following requirements are fulfilled: (1) The electrical installation in the

respective room corresponds to the specifications stated in this manual and (2) This equipment is

used, operated, and maintained according to this manual and Service Manual.

●The manufacturer is not liable for damage caused by unauthorized tampering with the device(s).

Such tampering will forfeit any rights to claim under warranty.

●This equipment may only be used together with accessories supplied by MOTIC’s. If the customer

makes use of other accessories, use them only if their safe usability under technical safety

aspectshas been proved and confirmed by MOTIC or the manufacturer of the accessory.

●Keep the User’s Manual and Service Manual in a place easily accessible at all times for persons

operating and maintaining the equipment.

●Do not force cable connections. If a cable does not connect easily, be sure that the connector (plug)

is appropriate for the receptacle (socket). If you cause any damage to a cable connector(s) or

receptacle(s), let the damage(s) be repaired by an authorized service technician.

●Please do not pull on any cable. Always hold on to the plug when disconnecting cables.

●Before every operation, visually check the equipment for exterior mechanical damage(s) and for

proper function.

●Immediately turn off and unplug any equipment that gives off smoke, sparks, strange noises, or

odors.

●After the equipment has been used in an observation of a specimen that is accompanied with a

potential of infection, clean the parts coming in contact with the specimen to prevent infection.

●In case the specimen is damaged by erroneous operation, promptly take the infection prevention

measures.

●Power Supply Cord set (international) - (Detachable) Rated 10 A, 250 V. Plug type CEE 7A/II,

Connector type IEC 60320/C13, and Cord type H05W-F3G, min. 0.75 mm2,3-conductor

terminating in molded-on grounding type attachment plug. <HAR> marked on the cord. Maximum

4.0 m long.

●Do not position the equipment so that it is difficult to operate the disconnecting device,

(disconnecting device: power cord, appliance inlet, etc.)

CAUTION

To avoid the risk of electric shock, this equipment must only be connected to a supply main with

protective earth.

The protection provided by the equipment may be impaired if the equipment is used in a manner not

specified by the manufacturer.

●When moving the microscope, grasp rear handle and the base with more than two peoples as

shown below.

2. INTRODUCTION

2.1 Indication for use (Intended use)

This instrument has been designed to be used to observe magnified images of specimens in routine and

research applications. Do not use this instrument for any purpose other than its intended use.

2.2 Classification

●Protection against electric shock: Class I

●Protection against harmful ingress of water: Ordinary, IPXO

●Mode of operation: Continuous

WARNING

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates,

uses, and can radiate radio frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio communications. Operation of this

equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

WARNING

Class A equipment is intended for use in an industrial environment. In the documentation for the user, a

statement shall be included drawing attention to the fact that there may be potential difficulties in

ensuring electromagnetic compatibility in other environments, due to conducted as well as radiated

disturbances.

3. OPERATING CONDITION

●As long as the device is in its original package it can be exposed to the following environmental

conditions for up to 15 weeks for shipping and storage without risk of damage:

A. Temperature range: from -40°C to +70°C;

B. Relative humidity range: below 100%;

●The device can be in the following storage conditions after unpackaged:

A. Temperature range: from -10°C to +55°C;

B. Relative humidity range: below 95%;

●The device is made to operate under the following environmental conditions:

A. Temperature range: from -10°C to +40°C;

B. Relative humidity range: below 85%;

The device neither generates nor receives electromagnetic interference when used near other

equipment. Therefore, no preventive or corrective measures are required.

Inhaltsverzeichnis

Andere Motic Mikroskop Handbücher

Motic

Motic RED 200 Series Bedienungsanleitung

Motic

Motic BA310Met-H Bedienungsanleitung

Motic

Motic BA310Met Bedienungsanleitung

Motic

Motic AE2000MET Bedienungsanleitung

Motic

Motic SILVER150 Series Bedienungsanleitung

Motic

Motic SMZ168 Series Bedienungsanleitung

Motic

Motic PM-1805 Bedienungsanleitung

Motic

Motic SMZ-161B Bedienungsanleitung

Motic

Motic BA410 Series Bedienungsanleitung

Motic

Motic BA310 Pol Bedienungsanleitung

Motic

Motic BA210 series Bedienungsanleitung

Motic

Motic MOTICAM T2 Bedienungsanleitung

Motic

Motic BA210 series Bedienungsanleitung

Motic

Motic BA210S Bedienungsanleitung

Motic

Motic SILVER250 Series Bedienungsanleitung

Motic

Motic BA210E Bedienungsanleitung

Motic

Motic BA310 Pol Bedienungsanleitung

Motic

Motic BA310 Pol Bedienungsanleitung

Motic

Motic SWIFTLINE MAE-31R Bedienungsanleitung

Motic

Motic Swiftline M30TZ-SM99CL Bedienungsanleitung

Motic

Motic SMZ-171 BL Bedienungsanleitung

Motic

Motic SILVER3H Series Bedienungsanleitung

Motic

Motic AE30 Bedienungsanleitung

Motic

Motic AE20 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung