Moxa Technologies IMC-P101 Series Bedienungsanleitung

P/N: 1802001015012

*1802001015012*

IMC-P101

Quick Installation Guide

Moxa PoE Media Converter

Edition 3.0, August 2016

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The IMC-P101 series is an Ethernet to fiber optic media converter. It

provides Ethernet media conversion from 10/100 BaseT(X) to 100

BaseFX(SC/ST connectors). These media converters are classified as

power source equipment (PSE), and when used in this way, the IMC-P101

series provides up to 15.4 watts to powered devices (PD). The IMC-P101

series can be used to power IEEE 802.3af compliant powered devices

(PD), eliminating the need for additional wiring, and supports IEEE

802.3/802.3u/802.3x with 10/100M, full/half-duplex, and MDI/MDI-X

auto-sensing to provide a total solution for your industrial Ethernet

network.

The IMC-P101 Series includes the following models:

•IMC-P101-M-SC: PoE Industrial 10/100BaseT(X) to 100BaseFX

media converter, multi-mode port with SC connector, 0 to 60°C

operating temperature.

•IMC-P101-M-ST: PoE Industrial 10/100BaseT(X) to 100BaseFX

media converter, multi-mode port with ST connector, 0 to 60°C

operating temperature.

•IMC-P101-S-SC: PoE Industrial 10/100BaseT(X) to 100BaseFX

media converter, single-mode port with SC connector, 0 to 60°C

operating temperature.

•IMC-P101-S-ST: PoE Industrial 10/100BaseT(X) to 100BaseFX

media converter, single-mode port with ST connector, 0 to 60°C

operating temperature.

•IMC-P101-M-SC-T: PoE Industrial 10/100BaseT(X) to 100BaseFX

media converter, multi-mode port with SC connector, -40 to 75°C

operating temperature.

•IMC-P101-M-ST-T: PoE Industrial 10/100BaseT(X) to 100BaseFX

media converter, multi-mode port with ST connector, -40 to 75°C

operating temperature.

•IMC-P101-S-SC-T: PoE Industrial 10/100BaseT(X) to 100BaseFX

media converter, single-mode port with SC connector, -40 to 75°C

operating temperature.

•IMC-P101-S-ST-T: PoE Industrial 10/100BaseT(X) to 100BaseFX

media converter, single-mode port with ST connector, -40 to 75°C

operating temperature.

NOTE

Throughout this Hardware Installation Guide, we often use IMC

as an abbreviatio

n for Moxa Industrial Media Converter:

IMC = Moxa Industrial Media Converter

Patent http://www.moxa.com/doc/operations/Moxa_Patent_Marking.pdf

- 3 -

Package Checklist

Moxa PoE Media Converter is shipped with the following items. If any of

these items is missing or damaged, please contact your customer service

representative for assistance.

•IMC-P101 series media converter.

•Quick Installation Guide (printed).

•Warranty Card.

Features

•10/100BaseT(X) Auto-Negotiation and Auto-MDI/MDI-X.

•IEEE 802.3af compliant PoE.

•Power failure by relay output.

•Provides up to 15.4W of power to powered devices (PD).

•Support Store-and-Forward mode and Pass Through mode.

•-40 to 75°C operating temperature range (T models).

•Redundant dual VDC power inputs.

- 4 -

Panel Layout of the IMC-P101 Series

1. Grounding screw

2. Terminal block for power input

PWR1/PWR2

Heat dissipation vents and relay

output

4. DIP switch

5. Power input PWR1 LED

6. Power input PWR2 LED

7. Fiber Link/Active LED

8. 100BaseFX (ST/SC connector)

Port

9. PSE Indicator LED

10.

10/100BaseT(X)

11.

TP port 10 Mbps LED

12.

TP port 100 Mbps LED

13.

Model Name

14.

Screw hole for wall mounting kit

15.

DIN-Rail mounting kit

- 5 -

Mounting Dimensions

- 6 -

DIN-Rail Mounting

The aluminum DIN-Rail attachment plate should be fixed to the back

panel of the IMC when you take it out of the box. If you need to reattach

the DIN-Rail attachment plate to the IMC, make sure the stiff metal spring

is situated towards the top, as shown in the figures below.

STEP 1:

Insert the top of the DIN

-Rail into

the slot just

below the stiff metal

spring.

STEP 2:

The DIN

-Rail attachment unit will

snap into place as shown below.

To remove the Moxa Industrial Media Converter from the DIN-Rail, simply

reverse Steps 1 and 2 above.

Wall Mounting (Optional)

For some applications, you will find it convenient to mount the Moxa PoE

Media Converter on the wall, as illustrated below.

STEP 1:

Remove the aluminum

DIN

-Rail attachment plate

from the Moxa

PoE Media

Converter, and then attach

the wall mount plates, as

shown in the diagram

s below.

STEP 2:

Mounting the Moxa

PoE Media Converter on the wall

requires 4 screws. Use the IMC, with wall mount plates

attached, as a guide to mark the correct locations of

the 4 screws. The heads of the screws should be less

than 6.0 mm in diameter, and the shafts should be less

than 3.5

mm in diameter, as shown in the figure at

the

right.

NOTE

Test the screw head and shank size by inserting the screw into

one of the keyhole shaped apertures of the Wall Mounting Plates,

before it is screwed into the wall.

Do not screw the screws in all the way—leave a space of about 2 mm to

allow room for sliding the wall mount panel between the wall and the

screws.

- 7 -

STEP 3:

Once the screws are fixed in the

wall, insert the four screw heads

through the large openings of the

keyhole

shaped apertures, and then

slide Moxa

PoE Media Converter

downwards, as indicated below.

Tighten the four screws for

added

stability.

Grounding the Moxa Industrial Media Converter

Grounding and wire routing help limit the effects of noise due to

electromagnetic interference (EMI). Run the ground connection from the

ground screw to the grounding surface prior to connecting devices.

ATTENTION

This product is intended to be mounted to a well

-grounded

mounting surface such as a metal panel.

Wiring the Redundant Power Inputs

The top five contacts of the 8-contact terminal block connector on the

IMC’s top panel are used for the IMC’s two DC inputs. Top and front views

of one of the terminal block connectors are shown here.

STEP 1: Insert the negative/positive DC wires

into the

V-/V+ terminals.

STEP 2:

To keep the DC wires from pulling

loose, use a small flat

-blade screwdriver to

tighten the wire

clamp screws on the front of

the terminal block connector.

STEP 3:

Insert the plastic terminal block

connector prongs into the terminal block

receptor, which is

located on the IMC’s top

panel.

ATTENTION

Before connecting the IMC to DC power inputs, make sure the DC

power source voltage is stable.

Communication Connections

IMC-P101 models have one 10/100BaseT(X) Ethernet port, and one

100BaseFX (SC or ST type connector) fiber port.

- 8 -

10/100BaseT(X) Ethernet Port Connection

The 10/100BaseT(X) Ethernet port located on the IMC’s front panel is

used to connect to Ethernet-enabled devices.

Illustrated below are pinouts for both MDI (NIC-type) ports and MDI-X

(HUB/Switch-type) ports, and also cable wiring diagrams for

straight-through and cross-over Ethernet cables.

10/100Base T(x) RJ45 Pinouts

MDI Port Pinouts

MDI-X Port Pinouts

8-pin RJ45

Signal

Tx+

Tx-

Rx+

Rx-

Signal

Rx+

Rx-

Tx+

Tx-

RJ45 (8-pin) to RJ45 (8-pin) Straight-Through Cable Wiring

RJ45 (8-pin) to RJ45 (8-pin) Cross-Over Cable Wiring

100BaseFX Ethernet Port Connection

The concept behind the SC port and cable is quite straightforward.

Suppose you are connecting devices I and II. Unlike electrical signals,

optical signals do not require a circuit in order to transmit data.

Consequently, one of the optical lines is used to transmit data from device

I to device II, and the other optical line is used transmit data from device

II to device I, for full-duplex transmission.

All you need to remember is to connect the Tx (transmit) port of device I

to the Rx (receive) port of device II, and the Rx (receive) port of device I

to the Tx (transmit) port of device II. If you are making your own cable,

we suggest labeling the two sides of the same line with the same letter

(A-to-A and B-to-B, as shown below, or A1-to-A2 and B1-to-B2).

- 9 -

SC-Port Pinouts

SC-Port to SC-Port Cable Wiring

ST-Port Pinouts

ST-Port to ST-Port Cable Wiring

ATTENTION

This is a Class 1 Laser/LED product. Do not stare into the Laser

Beam.

Redundant Power Inputs

Both power inputs can be connected simultaneously to live DC power

sources. If one power source fails, the other live source acts as a backup,

and automatically supplies all of the Moxa Industrial Media Converter’s

power needs.

DIP Switch Setting

DIP No.

Function

OFF

Auto Negotiation

Enable*

Disable

“ON”:

Enables “Auto Negotiation” function, the speed and duplex states

for each port link segment are automatically configured using the

highest performance interoperation mode.

“OFF”: Disables “Auto Negotiation” function, the speed and duplex

states depend on the manual setting configuration.

Force TP Speed

100Mbps*

10Mbps

(Only when Auto Negotiation is disabled)

“ON”:

Forces 100Mbps on Ethernet port.

“OFF”:

Forces 10Mbps on Ethernet port.

Force TP Duplex

Full Duplex*

Half Duplex

(Only when Auto Negotiation is disabled)

“ON”:

Forces Full Duplex on Ethernet port.

“OFF”:

Forces Half Duplex on Ethernet port.

- 10 -

DIP No.

Function

OFF

Link Fault Pass Through

Enable*

Disable

“ON”:

Enables “Link Fault Pass Through”, the link status on the TX port

will inform the FX port of the same device and vice versa.

“OFF”:

Disables “Link Fault Pass Through”, the link status on the TX port

will not inform the FX port.

Operating Mode

Store-and-Forward*

Pass Through

“ON”:

Selects “Store-and-Forward” mode, begins to forward a packet

to a destination port after an entire packet is received. The

latency depends on the packet length.

“OFF”:

Selects “Pass Through” mode, operates with the minimum

latency. Both transceivers are interconnected via internal MIIs

and the internal switch engine and data buffer are not used.

Note:

With “Pass Through” mode enabled, the Ethernet port and fiber

port should transmit at 100 Mbps, which is equivalent to full

duplex mode.

PSE

Disable

Enable*

PSE:

Power Source Equipment.

“ON”:

Disables “PSE”, IMC-P101 series do NOT provide power to PD

(Powered Device).

“OFF”:

Enables “PSE”, IMC-P101 series provides power to PD (Powered

Device).

P.R.R.

Enable

Disable*

P.R.R.:

Power Remote Reset

“ON”: Enables “P.R.R” function, when fiber port link down 3 seconds

and “PSE” setting is enabled, IMC-P101 series STOP providing

power to PD

(Power Device) which means the PD power will turn

OFF. After 1 second later, IMC-P101 series start to continue

provide power to PD, and then the PD power turn back ON for

reset PD.

“OFF”:

Disables “P.R.R” function, no reset PD function.

(*): Default DIP switch setting.

ATTENTION

After changing the DIP switch setting, you will need to power off

and then power on the IMC-P101 to activate the new setting.

LED Indicators

The front panel of Moxa Industrial Media Converter contains several LED

indicators. The function of each LED is described in the table below.

LED

Color

State

Description

PWR1 Green

Power is being supplied to power input

PWR1

OFF

Power is not being supplied to power

input PWR1

PWR2 Green

Power is being supplied to power input

PWR2

OFF Power is not being supplied to power

input PWR2

Fiber

Link/Act Green

Fiber port is active.

Blinking

Data is being transmitted or received.

OFF

Fiber port is inactive.

Andere Handbücher für IMC-P101 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort DE-311 Handbuch

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A IMC-21A Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Handbuch

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1180I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Media Converter Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME51 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1250I Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME61 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME50-M-SC Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-90 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 2141 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA Handbuch

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-M-ST Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung