Moxa Technologies VPort 254 Series Bedienungsanleitung

Moxa Industrial Video Encoder

VPort 254 Series

Quick Installation Guide

First Edition, October 2008

Reproduction without permission is prohibited.

Fl.4, No.135, Lane 235, Pao-Chiao Rd. Shing Tien City, Taipei, Taiwan,

R.O.C.

TEL: +886-2-8919-1230

P/N: 1802002540010

- 2 -

Overview

The VPort 254 is a 4-channel industrial video encoder that uses the ASIC

compression chip to provide video performance up to CIF (352 x 240) @ 120

FPS for a total of 4 channels. To meet the wide range of requirements from

end-users, the VPort 254 is designed to support dual-codecs, including MJPEG

and MPEG4 algorithms.

The VPort 254 inherits the VPort 351’s industrial features, but also supports

DIN-Rail mounting, 12/24 VDC and 24 VAC redundant power inputs, -40 to

75°C operating temperature (“T” models only), and IP30 protection for

industrial mission-critical applications. But most importantly, the VPort 254

meets critical hardware requirements for industrial safety and ruggedness, such

as UL508, which is pertinent to TA, UA, and MA systems.

Package Checklist

The VPort 254 is shipped with the following items:

VPort 254

10-pin terminal block for 1 power input and 4 digital inputs

8-pin terminal block for the other power input, and 2 relay outputs

5-pin terminal block for the RS-232/422/RS-485 PTZ control port

Quick Installation Guide

Document & Software CD (includes User’s Manual, Quick Installation

Guide, Moxa IVN Solution Datasheet and Utility).

Warranty Card

Note: If any of these items are missing or damaged, please contact your

customer service representative for assistance.

NOTE

Check the model name on the VPort’s side label to determine if the

model name is correct for your order.

NOTE

This product must be installed in compliance with your local laws

and regulations.

- 3 -

Features

High Performance Audio-Video Networking Solution

Works with NTSC/PAL analog video cameras

Supports MPEG4/MJPEG video compression technologies

4 BNC video inputs

Video stream up to 120 frames/sec in CIF (352 x 240) resolution through a

total of 4 channels

Selection from full D1, 4CIF, VGA, CIF, and QVGA resolutions

1 audio input and 1 audio output for 2-way voice communication

TCP, UDP, and HTTP network transmission modes

Supports Modbus/TCP for easy communication with SCADA systems

Standard RTSP (Real-time streaming protocol) for easy integration

Supports multicast (IGMP) protocols for efficient network transmission

Supports QoS (TOS) for priority transmission

Supports SNMP V1/V2c/V3 for network management

Built-in web server and RS-232 console for remote access and

configuration

One auto-sensing 10/100BaseT(X) Ethernet port or 100BaseFX

(SC connector)

Allow maximum of 8 simultaneous video streams of output

Set up video quality in CBR (constant bit rate) or VBR (variable bit rate)

Supports 1 RS-232/422/485 DB9 COM port for controlling a PTZ

(PAN/TILT/ZOOM) motorized camera or serial device via TCP/IP network

Supports 1 RS-232/RS-422/RS-485 5-pin PTZ port for controlling a PTZ

(PAN/TILT/ZOOM) motorized camera via TCP/IP network

UPnP and IP filtering supported

Industrial Rugged Design

Two 12/24 VDC and 24 VAC redundant power inputs with LED indicators

-40 to 75°C operating temperature for critical industrial environment

(“T” model)

35 mm DIN-Rail mounting or panel mounting installation

(with optional accessory)

IP30 form factor protection

CE, FCC, UL508 approvals for industrial applications

- 4 -

Intelligent Alarm Trigger Capability

Built-in Video Motion Detection (VMD) (firmware version V2.0 and later)

Equipped with 4 DIs and 2 relays (DO) for external sensors and alarms

(firmware version V2.0 and later)

Pre, trigger, and post alarm snapshot images provided

(firmware version V2.0 and later)

Supports sequential snapshot images

Messages with snapshot images can be sent via FTP and email

(firmware version V2.0 and later)

Capable of setting an alarm schedule

Video Management and Control

Moxa SoftDVR™Lite IP Surveillance Software for viewing and recording

bundled free

Free Moxa VPort SDK Plus supported with flexible interface and sample

code for customized application or system integration

NOTE

VMD and DI alarms are supported by V2.0 firmware version and

later

NOTE

If you are interested in Moxa VPort SDK PLUS, please go to

Moxa’s website

(www.moxa.com) to download the software, or

contact a Moxa sales

representative for more information.

- 5 -

VPort 254 Panel Layout

Grounding screw

RS-232 console port

Hardware reset button

8-pin terminal block for

Relay 1, Relay 2, and

power input 2 (PWR2)

10-pin terminal block for DI 1,

DI 2, DI 3, DI 4, power input 1

(PWR1)

Heat dissipation orifices

LEDs for STAT, PWR1,

PWR2, FAULT

LEDs for V1, V2, V3, V4

AUDIO INPUT port for mic-in

and line-in connection

10.

AUDIO OUTPUT port for

external speaker

11.

RS-232/422/485 COM port

with DB9 male connector for

PTZ camera or serial device

control

12.

RS-232/422/485 PTZ port

with 5-pin terminal block for

PTZ camera control

13.

4 BNC connectors for video

input

14.

RJ45 10/100BaseTX Ethernet

port with 10 Mbps, 1000

Mbps LEDs

15.

100BaseFX fiber optic port

with 100 Mbps LED

16.

Model name

17.

Screw hole for wall mounting

kit

18.

DIN-Rail mounting kit

- 6 -

First-Time Installation and

Configuration

Before installing the VPort 254, check to make sure that all items in the

package checklist are in the box. In addition, you will need access to a

notebook computer or PC equipped with an Ethernet port.

Step 1: Select the Power Source

The VPort 254 can be powered by a DC power input from 12 to 32 VDC, or an

AC power input from 18 to 30 VAC. Two power inputs are provided for

redundancy. Users can check the LED status located in the front panel to see if

the power inputs are connected appropriately. If one of the power inputs fails,

the FAULT LED will light up in red if the power failure alarm is enabled.

NOTE

The VPort 254 series support power input specifications of 12-32

VDC for 12/24

VDC power input, or 18-30 VAC for 24 VAC

power i

nput (note that this is different from Moxa EDS switch’s

-45 VDC power input).

Step 2: Connect the VPort 254 to a Network

The VPort 254 has an auto-sensing 10/100 Mbps RJ45 Ethernet port, or 100

Mbps fiber optic port (multi mode or single mode) for network connectivity.

Both the RJ45 port and fiber optic port have separate LEDs for 10 Mbps and

100 Mbps connections.

Step 3: Connect the VPort 254 to cameras and an audio source

The VPort 254 has 4 VIDEO INPUT ports (V1, V2, V3, V4). Use the BNC

connector (1.0 Vpp, 75Ω) and coaxial cable to connect video cameras to the

VPort to input analog video signals.

The VPort 254 has 1 audio input and 1 audio output. A microphone or an

amplifier can be plugged directly into the AUDIO INPUT port, and a speaker

can be plugged into the AUDIO OUTPUT port.

NOTE

Four LEDs (V1, V2, V3, and V4) are located on the VPort 254’s

front panel

to indicate the video signal transmission status for video

input

s. Check the LED status to see if the video is working

properly.

- 7 -

Step 4: Connecting motorized PTZ cameras and serial devices

The VPort 254 has 2 RS-232/422/485 ports. One is a COM PORT with DB9

male connector, and the other is a PTZ PORT with 5-pin terminal block

connector. Both ports can be used for connecting PTZ control cables for

controlling PTZ cameras over the TCP/IP network.

In addition, the COM PORT with DB9 male connector can also be used to

connect general serial devices, such as card readers, for transmitting serial data

over a TCP/IP network. This port can be used to connect serial devices to the

VPort 254 (however, the port cannot be used to connect video cameras).

To enable PTZ control, users should configure the PTZ control protocol in the

web-based manager.

NOTE

The PTZ control protocol is not standardized. To use a particular

PTZ

control protocol, the video server must support the driver for

that p

rotocol. Currently, the VPort 254 supports PTZ control

protocol drivers

for:

1. Pelco D

2. Pelco P

3. DynaColor DynaDome

you need to use a protocol that is not on the list, contact the

manufacturer of the camera to get t

he PTZ control commands, and

then program

its PTZ control using the VPort 254’s Custom

Camera

function.

NOTE

The VPort 254 comes with a PTZ driver upload function for

implementing new PTZ drivers. Please contact a Moxa sales

representative if you need as

sistance from Moxa’s R&D department

to create a new PTZ driver.

NOTE

The “Transparent PTZ Control” function in the camera driver list is

used to transmit the PTZ control signal over a TCP/IP network to

the VPort D351 video decoder or PC (additional drive

r required).

The PTZ control panel or keyboard can directly control the PTZ

camera or device, eliminating the need for a PTZ camera driver and

allowing the use of PTZ cameras with the VPort encoder.

- 8 -

Step 5: Configure the VPort 254’s IP address

After powering on the VPort 254, wait a few seconds for the POST (Power On

Self Test) to run. The STAT LED turns green to indicate that the POST process

has completed. The IP address will be assigned when the 10 or 100 Mbps

NETWORK LED blinks. The IP address assigned after the POST is completed

depends on the network environment.

Network Environment with DHCP Server

In this case, the IP address of the VPort 254 is assigned by a DHCP Server.

Use the DHCP Server’s IP address table, or use the Moxa VPort utility to

determine the IP address that was assigned by the DHCP Server.

NOTE

After powering on the VPort 254, wait a few seconds for the POST

(Power On Self Test) to run. The IP address will be assigned when

the 10 or 100 Mbps NETWORK LED blinks.

Using the Moxa VPort and EtherDevice Configurator Utility

(edscfgui.exe)

- 9 -

1. Run the edscfgui.exe program to search for the VPort and EDS switches.

After the Utility window opens, select or click on Broadcast Search, which

is located under the List Server menu, to initiate a search (note that you

can also click on Broadcast Search icon to initiate a search).

NOTE

You may download the VPort and EtherDevice Configurator

software from Moxa’s website at www.moxa.com.

2. The Broadcast Search window will show a list of all switches and VPorts

located on the network. The progress of the search will also be indicated.

3. When the search has ended, the Model Name, MAC address, and IP

address of the EDS switches and VPorts will be listed in the Utility

window.

- 10 -

NOTE

Broadcast Search can only search for devices connected to the

same LAN

subnet as the VPort. If your devices are located on a

different LAN

subnet, use the “Specify IP Address” function to

search for the device by keying in the IP address.

4. Double click the selected VPort, or use Internet Explorer to access the

VPort’s web-based manager (web console).

Network Environment without DHCP Server

If your VPort 254 is connected to a network that does not have a DHCP server,

then you will need to configure the IP address manually. The default IP address

of the VPort 254 is 192.168.127.100 and the default subnet mask is

255.255.255.0. Note that you may need to change your computer’s IP address

and subnet mask so that the computer is on the same subnet as the VPort.

To change the IP address of the VPort manually, access the VPort’s web server,

and then navigate to the System Configuration Network General page

to configure the IP address and other network settings. Check the Use fixed IP

address to ensure that the IP address you assign is not deleted each time the

VPort is restarted.

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies TCC-80I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 25 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-200-1213 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-101 Series Handbuch

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Media Converter Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1100 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1180I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5600-8-DT Bedienungsanleitung

Moxa Technologies

Moxa Technologies N Port Express Installations- und Benutzerhandbuch

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5110A Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA-T Handbuch

Moxa Technologies

Moxa Technologies ME60A Handbuch

Moxa Technologies

Moxa Technologies VPort 461 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1250I Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A IMC-21A Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1200 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-100 Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung