Moxa Technologies VPort 351 Series Bedienungsanleitung

MOXA Industrial Video Encoder

VPort 351 Series

Quick Installation Guide

Third Edition, May 2007

Moxa Networking Co., Ltd.

Tel: +886-2-8919-1230

Fax: +886-2-8919-1231

www.moxa.com

support@moxa.com (Worldwide)

support@usa.moxa.com (The Americas)

P/N: 1802003510112

—1 —

Overview

The VPort 351 is a high performance, 1-channel industrial video encoder that

provides up to full D1 (720 x480) @ 30 FPS video performance. The VPort

351 is designed to support multi-codecs, including MJPEG and MPEG4

algorithms. In addition, a continuous video pre/post event-trigger video record

function is supported to enhance video surveillance systems.

The VPort 351 has many of the same industrial-grade features as other MOXA

products, including DIN-rail mounting, 24 VAC/VDC redundant power inputs,

-40 to 75°C operating temperature (“-T” models), and IP30 protection for

industrial mission-critical applications. But most importantly, the VPort 351

meets critical industrial safety standards and approvals, such as UL508, and

Class 1, Div.2, making the encoder especially well suited for transportation,

utility, and manufacturing systems.

Package Checklist

The MOXA VPort 351 is shipped with the following items. If any of these

items are missing or damaged, please contact your customer service

representative for assistance.

y1 × VPort 351

y1 × 6-pin terminal block for one power input and 2 DIs

y1 × 8-pin terminal block for the other power input and 2 relay outputs

y1 × 5-pin terminal block for RS-232/422/485 PTZ control port

yQuick Installation Guide

yDocument & Software CD (includes User’s Manual, Quick Installation

Guide, MOXA IVN Solution Datasheet, and VPort Utility)

yWarranty Statement

NOTE Please check the model name on the VPort’s side label to verify

that the model name is correct for your order.

NOTE This product must be installed in compliance with your local laws

and regulations.

Features

High Performance Video/Audio Networking Solution

yWorks with NTSC/PAL analog video cameras

ySupports MPEG4/MJPEG video compression technology

y1 BNC video input and 1 BNC video output with 75Ωresistance

y1 audio input and 1 audio output for 2-way voice communication

yStandard RTSP (real-time streaming protocol) for easy integration

yMulticast (IGMP) protocols for efficient network transmission

yQoS (TOS) for priority transmission

yPPPoE and DDNS for xDSL connection

ySupports SNMP V3 for network management

yBuilt-in web server and RS-232 console for remote access & configuration

y1 auto-sensing 10/100BaseT(X) Ethernet port or 100baseFX (SC

connector)

—2 —

yTCP, UDP, and HTTP network transmission modes

yAllows simultaneous access of up to 10 clients

ySet video quality to CBR (constant bit rate) or VBR (variable bit rate)

yFull D1, 4CIF, VGA, QVGA, and CIF video resolution supported

yTimestamp and text overlay supported

yRS-232/RS-422/RS-485 COM port for controlling PTZ (PAN/TILT/ZOOM)

motorized camera

yUPnP and IP filtering supported

Industrial Rugged Design

yTwo 12/24 VDC and 24 VAC redundant power inputs with LED indicators

y-40 to 75°C operating temperature for critical industrial environments (“-T”

models)

y35 mm DIN-rail mounting or panel mounting installation (with optional

accessories)

yIP30 protection

yClass 1, Div.2 hazardous certification for critical environments (pending)

Intelligent Alarm Trigger

yBuilt-in Video Motion Detection (VMD)

yEquipped with 2 DIs and 2 relays (DO) for external sensors and alarms

yRecorded video provided for pre/post alarm

ySnapshot images provided for pre, trigger, and post alarm

ySequential snapshot images supported

yMessages with snapshot images can be sent via FTP or Email

yConfigure alarm activation schedule

Video Management and Control

yMOXA SoftDVR™ Lite IP Surveillance Software for viewing and

recording bundled free

yFree MOXA IVN SDK supported with flexible interface and sample codes

for customized applications or system integration

NOTE MJPEG, PPPoE, DDNS, QoS, and SNMP will be supported

starting with the release of V2.0 firmware. Please check MOXA’s

website for updates about new firmware releases.

NOTE A version of SoftDVR Lite that supports the VPort 351 will be

released on MOXA’s website soon. Please check MOXA’s website

for updates about new firmware releases.

NOTE If you are interested in the MOXA IVN SDK, please go to

MOXA’s website to download the software, or contact a MOXA

sales representative for more information.

— 3 —

VPort 351 Panel Layout

VPort 351

Front Panel View

VPort 351-M-SC

Front Panel View

Top Panel View

Rear Panel View

V1, V2: 12-32 VDC

12-30 VAC

RS-232

CONSOLE

1. Grounding screw

2. RS-232 console port

3. Hardware reset button

4. 6-pin terminal block for DI 1, DI 2,

power input 2 (PWR2)

5. 8-pin terminal block for Relay 1, Relay

2, power input 1 (PWR1)

6. Heat dissipation orifices

7. LEDs for STAT, PWR1, PWR2, FAULT

8. LEDs for VIDEO, AUDIO TEST, PTZ

9. AUDIO OUTPUT port for external

speaker

10. AUDIO INPUT port for mic-in and

line-in connection

11. 5-pin terminal block for RS-232/422/

485 connection

12. BNC port for video input

13. AUDIO TEST DIP switch for testing

audio input signal (default is off)

14. 75Ω DIP switch for analog video signal

transmission with 75Ω resistance

(default is on)

15. BNC port for loop-through video output

16. RJ45 10/100BaseTX Ethernet Port with

10 Mbps, 100 Mbps LEDs

17. 100BaseFX Fiber optic port with 100

Mbps LED

18. Model name

19. Screw hole for wall mounting kit

20. DIN-Rail mounting kit

—4 —

First-Time Installation and

Configuration

Before installing the VPort 351 video encoder, check to make sure that all

items in the Package Checklist are in the box. In addition, you will need to use

a notebook or PC equipped with an Ethernet port.

Step 1: Select the Power Source

The VPort 351 can be powered by a DC power input from 12 to 32 VDC, or an

AC power input from 18 to 30 VAC. Two power inputs are provided for

redundancy. Users can check the LED status located on the front panel to see if

the power inputs are connected appropriately. If one of the power inputs fails,

the FAULT LED will illuminate in red.

NOTE The VPort 351 has 2 power inputs for redundancy. Each power

input supports 12 to 32 VDC for a 12/24 VDC power input, or 18

to 30 VAC for a 24 VAC power input. This differs from MOXA’s

EDS switches, which support a 12 to 45 VDC power input.

Step 2: Connect the VPort 351 to the Network

The VPort 351 has an auto-sensing 10/100 Mbps RJ45 Ethernet port, or 100

Mbps fiber optic port (multi mode or single mode) for network connectivity.

Both the RJ45 port and fiber optic port have separate LEDs for 10 Mbps and

100 Mbps connection activity.

Step 3: Connect the VPort 351 to a camera and an audio source

The VPort 351 has a VIDEO INPUT port and a loop-through VIDEO

OUTPUT port with a 75Ωresistance dip switch. Users should use the BNC

connector and coaxial cable to connect the video camera to the VPort to input

analog video signals, and connect the monitor or DVR with the VPort to output

analog signals (note that the 75Ωresistance should be turned to off when the

video output is enabled).

The VPort 351 has 1 audio input and 1 audio output. A microphone or an

amplifier can be plugged directly into the AUDIO INPUT port; a speaker can

be plugged into the AUDIO OUTPUT port.

NOTE A VIDEO LED is located on the front panel to indicate the video

signal transmission status for the video input. Users can check the

LED status to see if the video is working properly.

Step 4: Connecting the VPort 351 to a motorized PTZ camera/device

If you are using a PTZ camera or device, you need to connect the PTZ control

cable to the VPort 351’s PTZ port. The PTZ port is a 5-pin terminal block for

RS-232/422/485 serial connection. The pin assignments are shown below.

PIN RS-422/485 RS-232

1 GND

Ground GND Ground

2 R- Rx- --- N/A

3 R+ Rx+ RxD RxD

4 T-\D-

Tx-/ Data- --- N/A

5 T+\D+

Tx+/ Data+ TxD TxD

To enable PTZ control, configure the PTZ control protocol in the web-based

manager.

—5 —

NOTE The PTZ control protocol is not standardized. To use a particular

PTZ control protocol, the video server must support the driver for

that protocol. Currently, the VPort 351 supports PTZ control

protocol drivers for:

1. Pelco D

2. DynaColor SmartDome (supported by V2.0 firmware)

If you need to use a protocol that is not on the list, you will need to

contact the manufacturer of the camera to get the PTZ control

commands, and then program its PTZ control in the VPort 351’s

Custom Camera function.

NOTE The VPort 351 comes with a PTZ driver upload function for

implementing new PTZ drivers. Please contact a MOXA sales

representative if you need assistance from MOXA’s R&D

department to create a new PTZ driver.

Step 5: Configure the VPort 351’s IP address

After powering on the VPort 351, wait a few seconds for the POST (Power On

Self Test) to run. The STAT LED turns green to indicate that the POST process

has completed. The IP address will be assigned when the 10 or 100 Mbps

NETWORK LED blinks. The IP address assigned after the POST is completed

depends on the network environment.

Network Environment with DHCP Server

In this case, the IP address of the VPort 351 is assigned by a DHCP Server.

Use the DHCP Server’s IP address table, or use the MOXA VPort utility to

determine the IP address that was assigned by the DHCP Server.

NOTE After powering on the VPort 351, wait a few seconds for the POST

(Power On Self Test) to run. The IP address will be assigned when

the 10 or 100 Mbps NETWORK LED blinks.

Using the VPort Utility

1. Run the VPort_Utility.exe program to search for the VPort . After the

VPort Utility window opens, you may also click on the Search button to

initiate a search.

—6 —

2. When the search has finished, the Model Name, IP address, MAC address,

Serial (i.e., serial number), and HTTP Port of the VPort will be listed in

the VPort Utility window.

NOTE Serial refers to the production serial number of this VPort, and the

HTTP Port number is the http port used by this VPort.

3. Double click on the selected VPort, or use the IE web browser to access

the VPort’s web-based manager (web server).

Network Environment without DHCP Server

If your VPort 351 is connected to a network that does not have a DHCP server,

then you will need to configure the IP address manually. The default IP address

of the VPort 351 is 192.168.127.100 and the default subnet mask is

255.255.255.0. Note that you may need to change your computer’s IP address

and subnet mask so that the computer is on the same subnet as the VPort.

To change the IP address of VPort manually, access the VPort’s web server,

and then navigate to the System Configuration ÆNetwork ÆGeneral page

to configure the IP address and other network settings. Checkmark Use fixed

IP address to ensure that the IP address you assign is not deleted each time the

VPort is restarted.

Step 6: Logging in to the VPort 351 web-based manager

Type the IP address in the web browser’s address input box and then press

enter.

Step 7: Installing the ActiveX Control Plug-in

A security warning message will appear the first time you access the VPort’s

web-based manager. The message is related to installing the VPort AcitveX

Control component to your PC or notebook. Click on Yes to install this plug-in

to enable the IE web browser for viewing video images.

—7 —

NOTE For Windows XP SP2 or above operating systems, the ActiveX

Control component will be blocked for system security reasons. In

this case, the VPort’s security warning message window may not

appear. Users should unblock the ActiveX control function or

disable the security configuration to enable the installation of

VPort’s ActiveX Control component.

Step 8: Accessing the Homepage of the VPort 351’s web-based manager

After installing the ActiveX Control component, the homepage of the VPort

351’s web-based manager will appear. Check the following items to make sure

the system was installed properly:

1. Video Images

2. Audio Sound (make sure your PC’s or notebook’s sound is turned on)

3. Video Information

—8 —

Step 9: Accessing VPort’s System Configuration

Click on System Configuration to access the overview of the system

configuration to change the configuration. Model Name, Server Name, IP

Address, MAC Address, Firmware Version, and LED Status appear in the

green bar near the top of the page. Use this information to check the system

information and installation.

For details of each configuration, check the User’s Manual on the software CD.

NOTE After accessing the VPort 351’s web-based manager,

administrators should access System Configuration ÆSystem Æ

Account to set up the administrator’s password and enable the

authentication function. The administrator account name is admin.

An authentication window will pop up requesting the account name

and password each time the VPort 351 is accessed.

Andere Handbücher für VPort 351 Series

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies UPORT 1100 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NE-4100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A series Handbuch

Moxa Technologies

Moxa Technologies PTC-101-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-82 Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1400 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-100 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort D361 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies MIINEPORT E1 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies A50 Bedienungsanleitung

Moxa Technologies

Moxa Technologies MGate 5118 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A IMC-21A Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-RM Series Handbuch

Moxa Technologies

Moxa Technologies Transio TCC-80 V2.2 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 1250I Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5410 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort DE-311 Handbuch

Moxa Technologies

Moxa Technologies TCF-142-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-200-1213 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1110 Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung