Moxa Technologies NPort 5410 Bedienungsanleitung

Reset Button—Press the Reset button continuously for 5 sec to load

factory defaults: Use a pointed object, such as a straightened paper clip or

toothpick, to press the reset button. This will cause the Ready LED to

blink on and off. The factory defaults will be loaded once the Ready LED

stops blinking (after about 5 seconds). At this point, you should release

the reset button.

5410/5430/5430I

Quick Installation Guide

First Edition, May 2003

LED Indicators—NPort 5400’s top panel contains six LED indicators,

as described in the following table.

LED Name LED Color LED Function

red

Steady on: Power is on and NPort is booting up.

Blinking: Indicates an IP conflict, or DHCP

or BOOTP server did not respond

properly.

green

Steady on: Power is on and NPort is

functioning normally.

Blinking: The NPort has been located by

NPort Administrator’s Location

function.

Ready

off Power is off, or power error condition exists.

orange 10 Mbps Ethernet connection.

green 100 Mbps Ethernet connection.

Link

off Ethernet cable is disconnected, or has a short.

orange Serial port is receiving data.

green Serial port is transmitting data.

P1, P2,

P3, P4 off No data is being transmitted or received through

the serial port.

1. Overview

Welcome to Moxa NPort 5400, a 4 port communication device that

allows you to control RS-232 (for NPort 5410) or RS-422/485

(for NPort 5430/5430I) serial devices over a TCP/IP based Ethernet.

2. Package Checklist

Before installing NPort 5400, verify that the package contains the

following items:

 1 NPort 5400 4-Port Serial Device Server

 NPort Document & Software CD

 NPort 5410/5430/5430I Quick Installation Guide

 Product Warranty

Optional Accessories

DK-35A For 35 mm DIN-Rail; includes 4 screws

Notify your sales representative if any of the above items is missing or

damaged.

LCM Display Panel—When the NPort 5400 unit is powered up, you will

a see a display similar to:

3. Hardware Introduction

As shown in the following figures, NPort 5410 has 4 Male DB9 ports, for

the RS-232 interface, and NPort 5430/5430I has 4 5-pin terminal blocks,

for the RS-422/485 interface.

NP5410_61405

1 9 2 . 1 6 8 . 1 2 7 . 2 5 4

This is where NP5410_61405 is the server’s name, and 192.168.127.254

is the server’s IP address.

LCM Panel Operation—There are four buttons on NPort 5400’s top

panel used to operate the server’s LCM panel. Going from left to right,

the buttons are:

Button Action

MENU Activates the main menu, or returns to a lower level.

Scrolls up through a list of items shown on the LCM

panel’s second line.

Scrolls down through a list of items shown on the LCM

panel’s second line.

SEL Selects the option listed on the LCM panel’s second line.

Detailed LCM Panel Operating instructions can be found on the

CD-ROM in the “NPort 5410/5430/5430I User’s Manual.”

—3—

—1——2—

4. Hardware Installation Procedure

STEP 1: After removing NPort 5400 from the box, the first thing you

should do is attach the power adaptor.

STEP 2: Connect NPort 5400 to a network. Use a standard

straight-through Ethernet cable to connect to a Hub or Switch. When

setting up or testing NPort 5400, you might find it convenient to connect

directly to your computer’s Ethernet port. In this case, use a cross-over

Ethernet cable.

STEP 3: Connect NPort 5400’s serial port to a serial device.

STEP 4: Placement Options

In addition to

placing NPort 5400

on a desktop or

other horizontal

surface, you may

also make use of

the DIN-Rail or

Wall Mount

options, as

illustrated here.

Wall Mount

DIN-Rail

5. Software Installation Information

To install NPort Administration Suite, insert the NPort Document &

Software CD into your computer’s CD-ROM drive. Once the NPort

Installation CD window opens, click on the Installation button, and then

follow the instructions on the screen.

To view detailed information about NPort Administration Suite, click

on the Documents button, and then select “NPort 5410/5430/5430I

User’s Manual” to open the pdf version of this user’s guide.

6. Pin Assignments and Cable Wiring—NPort 5410

DB9 Male Port Pinouts

RS-232 Wiring

DB9 Female to DB9 Male

DB9 Female to DB25 Male

7. Terminal Block Wiring—NPort 5430

8. Environmental Specifications

Power requirements

NPort 5410

NPort 5430

NPort 5430I

12 to 48 VDC, 385 mA at 12V (max.)

12 to 48 VDC, 380 mA at 12V (max.)

12 to 48 VDC, 600 mA at 12V (max)

Operating temp. 0 to 55◦C (32 to 131◦F)

Operating humidity 5 to 95% RH

Dimensions

(W×D×H)

158 × 33 × 103 mm

6.22 × 1.3 × 4.06 inch

Surge protection 15 KV ESD for serial port

Magnetic isolation 1.5 KV for Ethernet

Power line protection 4 KV Burst (EFT), EN61000-4-4

2 KV Surge, EN61000-4-5

Regulatory approvals FCC Class A, CE Class A, UL, CUL, TÜV

Moxa Technologies Co., Ltd.

Reproduction without permission is prohibited.

Tel:+886-2-8919-1230

Fax:+886-2-8919-1231

www.moxa.com

support@moxa.com.tw

P/N: 18020540000

—6—

—5—

—4—

Andere Handbücher für NPort 5410

Dieses Handbuch passt für folgende Modelle

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies VPort 2141 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 461 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2210 Bedienungsanleitung

Moxa Technologies

Moxa Technologies N Port Express Installations- und Benutzerhandbuch

Moxa Technologies

Moxa Technologies NPort DE-311 Handbuch

Moxa Technologies

Moxa Technologies TCC-80I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-RM Series Handbuch

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-80 V2.2 Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1100 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Z2150 Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101-M12 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 351 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCC-120 Handbuch

Moxa Technologies

Moxa Technologies VPort 364 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 451 Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A series Handbuch

Moxa Technologies

Moxa Technologies VPort 25 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPort 2000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-S Bedienungsanleitung

Moxa Technologies

Moxa Technologies CSM-400 Series Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung