Moxa Technologies MGate 5118 Series Bedienungsanleitung

P/N: 1802051180011

*1802051180011*

MGate 5118

Quick Installation Guide

Edition 1.1, October 2018

Technical Support Contact Information

www.moxa.com/support

Moxa Americas:

Toll

-free: 1-888-669-2872

Tel:

1-714-528-6777

Fax:

1-714-528-6778

Moxa China (Shanghai office):

Toll

-free: 800-820-5036

Tel:

+86-21-5258-9955

Fax:

+86-21-5258-5505

Moxa Europe:

Tel:

+49-89-3 70 03 99-0

Fax:

+49-89-3 70 03 99-99

Moxa Asia-Pacific:

Tel:

+886-2-8919-1230

Fax:

+886-2-8919-1231

Moxa India:

Tel:

+91-80-4172-9088

Fax:

+91-80-4132-1045



- 2 -

Overview

The MGate 5118 is an industrial Ethernet gateway for J1939-to-Modbus

RTU/ASCII/TCP, PROFINET and EtherNet/IP network communications.

Package Checklist

Before installing the MGate 5118, verify that the package contains the

following items:

•1 MGate 5118 gateway

•Quick installation guide (printed)

•Warranty card

Please notify your sales representative if any of the above items is

missing or damaged.

Optional Accessories (can be purchased separately)

•Mini DB9F-to-TB: DB9-female-to-terminal-block connector

•WK-51-01: Wall-mounting kit, 51 mm wide

Hardware Introduction

LED Indicators

LED

Color

Description

PWR 1,

PWR 2

Green

The power cable is connected

Off

The power cable is disconnected

Ready

Off

Power is off or a fault condition exists

Green Steady on: Power is on, and the unit is functioning

normally

Blinking: The unit is responding to the software’s

Locate function

Red Steady on: Power is on, and the unit is booting up

Blinking: Indicates an IP conflict, or the DHCP or

BOOTP server is not responding properly

Flashing quickly: the microSD card failed

LAN

Green

(Flashing

only)

The Ethernet port is receiving or transmitting data

Modbus TCP Client:

Modbus communication in progress

Modbus TCP Server:

Modbus communication in progress

EIP Scanner:

I/O is exchanging data with at least one device

EIP Adapter: I/O is exchanging data

PROFINET: PROFINET I/O interface is exchanging

data

- 3 -

LED

Color

Description

Red

(Flashing

only)

A communication error occurred

Modbus TCP Client:

1. Received an exception code or framing error

(parity error, checksum error)

2. Command timeout (slave device is not

responding)

3. TCP connection timeout

Modbus TCP Server:

1. Received an invalid function code or framing

error (parity error, checksum error)

2. Accessed invalid register address or coil address

Ethernet/IP Scanner:

1. Command timeout (the adapter is not

responding)

2. TCP connection timeout

Ethernet/IP Adapter:

The connection was refused due to incorrect

configuration

Off

No communication

MB* Green

(Flashing

only)

Modbus is receiving or transmitting data

Red

(Flashing

only)

A communication error occurred

Master Mode:

1. Received an exception code or framing error

(parity error, checksum error)

2. Command timeout (the slave device is not

responding)

Slave Mode:

1. Received an invalid function code or framing

error (parity error, checksum error)

2. Accessed invalid register address or coil address

Off

No communication

CAN Green

(Flashing

only)

CANbus(J1939) communication is receiving or

transmitting data

Red

(Steady)

A communication error occurred

1. The J1939 address claim failed

2. CAN is in bus-off state because the error counter

is exceeding its limitations

Off

No communication

Eth1,

Eth2

Green

Indicates an 100 Mbps Ethernet connection

Amber

Indicates a 10 Mbps Ethernet connection

Off

The Ethernet cable is disconnected

*Only indicates serial communication status; for Modbus TCP status,

please refer to LAN LED indicator.

- 4 -

Dimensions

Unit = mm (inch)

Reset Button

Restore the MGate to factory default settings by using a pointed object

(such as a straightened paper clip) to hold the reset button down until

the Ready LED stops blinking (approximately five seconds).

Pull-high, Pull-low, and Terminator for RS-485 and CAN

On the MGate 5118’s left side panel, you will find DIP

switches to adjust each CAN port or serial port’s pull

high resistor, pull

-low resistor, and terminator.

CAN

MODBUS

Pull-

high

resistor

Pull-low

resistor

Terminator

Pull-high

resistor

Pull-low

resistor

Terminator

Reserved

120 Ω

(default)

1 kΩ 1 kΩ 120 Ω

OFF –

150 kΩ

(default)

150 kΩ

(default)

– (default)

Hardware Installation Procedure

1. Connect the power adapter. Connect the 12-48 VDC power line or

DIN-rail power supply to the MGate 5118’s terminal block.

2. Use a serial cable to connect the MGate to the Modbus or CAN

device.

3. Use an Ethernet cable to connect the MGate to the Modbus,

Ethernet/IP or PROFINET device.

4. The MGate 5118 is designed to be attached to a DIN rail or

mounted on a wall. For DIN-rail mounting, push down the spring

- 5 -

and properly attach it to the DIN rail until it “snaps” into place. For

wall mounting, install the wall-mount kit (optional) first and then

screw the device onto the wall. The following figure illustrates the

two mounting options:

Software Installation Information

You can download the User's Manual and DSU (Device Search Utility)

from Moxa's website: www.moxa.com. Please refer to the User’s

Manual for additional details on using the Device Search Utility.

The MGate 5118 also supports login via a web browser.

Default IP address: 192.168.127.254

Default account: admin

Default password: moxa

Pin Assignments

Modbus Serial Port (Male DB9)

Pin RS-232

RS-422/

RS-485 (4W)

RS-485 (2W)

DCD

TxD-(A)

–

RXD

TxD+(B)

–

TXD

RxD+(B)

Data+(B)

DTR

RxD-(A)

Data-(A)

GND

DSR

–

RTS

–

CTS

–

*Signal ground

CAN Port (6-pin Terminal Block)

CAN

CAN_L

CAN_H

CAN Signal GND

Ext-CAN_L*

Ext-CAN_H*

CAN_SHLD

- 6 -

* For the CAN port, plug CAN_L and CAN_H into the terminal block. If

another device is connected to the same CAN bus, use the Ext_CAN_L

and Ext_CAN_H as extension pins.

Ethernet Port (RJ45)

Signal

Tx+

Tx-

Rx+

Rx-

Console Port (RS-232)

The MGate 5118 series can use a RJ45 serial port to connect to a PC to

configure the device.

Signal

DSR

RTS

GND

TXD

RXD

DCD

CTS

DTR

Power Input and Relay Output Pinouts

V2+ V2-

V1+ V1-

Shielded

Ground

Power

Input 2

Power

Input 2

N.O. Common

N.C.

Power

Input 1

Power

Input 1

Specifications

Power Requirements

Power Input

12 to 48 VDC

Power Consumption

416mA@12VDC, 195mA@24VDC,

110mA@48VDC

Operating Temperature

Standard model:

0 to 60°C (32 to 140°F)

Wide temperature model:

-40 to 75°C (-40 to 167°F)

Ambient Relative Humidity

5 to 95% RH

Dimensions

45.8 x 105 x 134 mm (1.80 x 4.13 x 5.27

in)

Reliability

Alert Tools

Built-in buzzer and RTC

MTBF

727,873 hrs.

- 7 -

NOTE

In the following section, ATEX and C1D2 certifications will be

detailed separately.

ATEX Information

1. DEMKO Certificate number: 17 ATEX 1848X

IECEx Certificate number: IECEx UL 17.0019X

2. Ambient Temperature Range:

0°C to 60°C (for models without suffix –T)

-40°C to 75°C (for models with suffix –T only)

3. Certification String: Ex nA nC IIC T4 Gc

4. Standards Covered: EN 60079-0:2012+A11:2013/IEC 60079-0 6th

Ed. AND EN 60079-15:2010/IEC 60079-15 4th Ed.

5. The conditions of safe use:

a. The equipment shall be installed in an enclosure that provides a

degree of protection not less than IP 54 in accordance with

IEC/EN 60079-15 and accessible only by the use of a tool.

b. Devices are for use in an area of not more than pollution

degree 2 in accordance with IEC/EN 60664-1.

c. Provisions shall be made, either in the equipment or external to

the equipment, to prevent the rated voltage from being

exceeded by the transient disturbances of more than 140% of

the peak-rated voltage.

Installation instructions

a. When wiring the relay contact (R), digital input (DI), and power

inputs (P1/P2), we suggest using AWG (American Wire Gauge) 12-28

(0.0804-3.31 mm²) as a cable and the corresponding pin-type cable

terminals. The connector can withstand a maximum torque of 4.5 inch-

pounds.

b. Conductors suitable for use in an ambient temperature of 85°C must

be used for the power input terminal block.

c. The cross-sectional area of the earthing conductors shall be at least

3.31 mm²

C1D2 Information

1. These devices are open-type devices that are to be installed in an

enclosure only accessible with the use of a tool and suitable for the

environment.

2. This equipment is suitable for use in Class I, Division 2, Groups A, B,

C, and D or non-hazardous locations only.”

WARNING

EXPLOSION HAZARD

Do not disconnect the equipment unless the power has been

switched off, or the area is known to be nonhazardous.

- 8 -

WARNING

EXPLOSION HAZARD

The substitution of any components may impair suitability for

Class 1, Division 2.

WARNING

EXPOSURE TO SOME CHEMICALS MAY DEGRADE THE SEALING

PROPERTIES OF MATERIALS USED IN THE FOLLOWING

DEVICE: Sealed Relay Device U21.

WARNING

EXPLOTION HAZARD

Indoor use and Pollution degree 2.

WARNING

EXPLOTION HAZARD

The equipment and label must be wiped by a dry cloth.

WARNING

EXPLOTION HAZARD

This unit is intended

to be supplied by an UL Listed/IEC 60950-

1 approved power supply suitable for use at 75°C. And the

power supply output meets SELV, LPS and rated output 12

-48

VDC, and 416 mA minimum.

Moxa Inc.

Fl. 4, No. 135, Lane 235, Baoqiao Rd.

Xindian Dist., New Taipei City, 23145

Taiwan, R.O.C.

Andere Handbücher für MGate 5118 Series

Inhaltsverzeichnis

Andere Moxa Technologies Medienkonverter Handbücher

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio A52 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5000 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21A IMC-21A Bedienungsanleitung

Moxa Technologies

Moxa Technologies N Port Express Installations- und Benutzerhandbuch

Moxa Technologies

Moxa Technologies TCF-142-S-ST-RM Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-21GA-T Handbuch

Moxa Technologies

Moxa Technologies Transio TCC-80I Bedienungsanleitung

Moxa Technologies

Moxa Technologies UPORT 1400 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies PTC-101 Series Handbuch

Moxa Technologies

Moxa Technologies UPort 1400-G2 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ME61 Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort 5100A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-P101 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies Transio TCC-80 V2.2 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1170I Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies TCF-142-M-ST Bedienungsanleitung

Moxa Technologies

Moxa Technologies IMC-P101 Series Handbuch

Moxa Technologies

Moxa Technologies VPort 251 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1150 series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 461 Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies VPort 364A Series Bedienungsanleitung

Moxa Technologies

Moxa Technologies NPort Z2150 Bedienungsanleitung

Moxa Technologies

Moxa Technologies ICF-1170I-M-ST Bedienungsanleitung

Beliebte Medienkonverter Handbücher anderer Marken

SoundTraxx

SoundTraxx Blunami BLU-2200 Bedienungsanleitung

SPROLINK

SPROLINK VA1 Bedienungsanleitung

Acclaim Lighting

Acclaim Lighting DDC-1-AC Bedienungsanleitung

Nikon

Nikon AF-S TC-20E III Bedienungsanleitung

Axis

Axis AXIS Q7406 Bedienungsanleitung

Omega

Omega TAC80B-J Bedienungsanleitung

Zoom

Zoom Thunderbolt TAC-2R Bedienungsanleitung

OST

OST iConverter 10/100M Bedienungsanleitung

Vertiv

Vertiv Netsure Bedienungsanleitung

birddog

birddog MINI Bedienungsanleitung

Roland

Roland GI-10 Bedienungsanleitung

Wallenstein

Wallenstein WX310 Bedienungsanleitung

Pace

Pace MSS 200-1 Bedienungsanleitung

Solar Converters

Solar Converters EQ 12/24-50 Bedienungsanleitung

CYP

CYP EL-7400V Bedienungsanleitung

TIE

TIE MIDI 1i1o Bedienungsanleitung

DCS

DCS Vivaldi Upsampler Bedienungsanleitung

Westermo

Westermo MCW-211 SERIES Bedienungsanleitung