Nikon Eclipse 800 Bedienungsanleitung
2022/01/12 17:32 1/9 Nikon Eclipse 800 Microscope Motor Drive Installation
Applied Scientific Instrumentation - https://asiimaging.com/docs/
Nikon Eclipse 800 Microscope Motor Drive
Installation
This procedure steps you through the installation and alignment of the DRV-E800 motor drive onto
the Nikon Eclipse 800 microscope.
The following tools are required to install the ASI drive onto the Nikon Eclipse 800 microscope:
Small Phillips screwdriver
Small knife or flat bladed instrument for prying
7/32 or 5.5mm driver wrench (provided)
5/64” hex wrench (provided)
2.5mm hex wrench (provided)
2mm hex wrench (provided)
Motor Drive Installation
The ASI z-axis drive attaches and drives the fine focus shaft of the microscope. The drive assembly is
secured to the microscope via a custom ASI base plate that mounts to the microscope utilizing a
clamp assembly that secures the base plate to the bottom of the microscope. Precise alignment of the
ASI drive onto the fine focus shaft of the microscope is accomplished through a triple axis sliding
adjustment bar. Installing the ASI drive assembly involves six steps:
Note: the terms left and right refer to the sides of the microscope as viewed from the
front of the microscope and assemblies.
Last update: 2021/09/23 17:15 nikon_eclipse_800_zdrive https://asiimaging.com/docs/nikon_eclipse_800_zdrive
https://asiimaging.com/docs/ Printed on 2022/01/12 17:32
Installing ASI Drive gear
Step 1 - Removing the right fine focus knob,
and installing the ASI cover and drive gear
As shown in the above photos use the small knife, or sharp instrument, to pry off the small round
black cover located in the middle of the right fine focus knob. Use the 7/32 or 5.5mm driver wrench to
remove the nut that is located in the center of the fine focus knob. It will be necessary to hold the left
fine focus knob when removing this nut to keep the fine focus shaft from turning.
After the nut is removed remove the right fine focus knob by unscrewing it, counter clock wise, from
the fine focus shaft. Please note that it may be necessary to hold the left fine focus knob when
removing the right fine focus knob in order to keep the fine focus shaft from turning. After removing
the knob locate the ASI cover and install it in place of the cover just removed.
After completely screwing the ASI cover on to the microscope fine focus shaft as shown locate the ASI
drive gear, this may be on the ASI drive and will need to be removed from the drive as shown. Loosen
the screw on the clamp, and screw it onto the threaded part of the shaft. Insure that the clamp is lose
before you try to screw it on. Screw the shaft all of the way onto the microscope then press the gear
completely against the microscope / ASI cover. Use the 7/64” Allen wrench to securely tighten the
clamp, thus securing the complete assembly onto the microscope.
Drive with cover & knob installed
2022/01/12 17:32 5/9 Nikon Eclipse 800 Microscope Motor Drive Installation
Applied Scientific Instrumentation - https://asiimaging.com/docs/
Drive without knob & cover
Adjustment Screws(2.5mm hex wrench)
Remove this clamp
Step 2 – Preparing the ASI drive for installation
Please refer to the above photographs. Locate the ASI Drive assembly, if the unit has shipped with the
knob and cover attached use the 2mm Allen wrench to remove the knob and cover as shown. Loosen
Last update: 2021/09/23 17:15 nikon_eclipse_800_zdrive https://asiimaging.com/docs/nikon_eclipse_800_zdrive
https://asiimaging.com/docs/ Printed on 2022/01/12 17:32
all of the adjustment screws, but do not remove them. They should be loosened just enough so that
the drive moves freely in all axis along the base plate. Remove the clamp assembly from the left hand
side of the base plate by removing the two screws that secure it. Set the clamp and the screws aside
as they will be used in the next step.
Drive installed
Drive shaft bearing
Drive gear aligns with encoder gear
2022/01/12 17:32 7/9 Nikon Eclipse 800 Microscope Motor Drive Installation
Applied Scientific Instrumentation - https://asiimaging.com/docs/
Install & tighten base clamp (2mm hex wrench)
Install Cover(2mm hex wrench)
Install focus knob(2mm hex wrench)
Step 3 - Installing and aligning the ASI motor assembly
Facing the front of the microscope hold the motor assembly in your right hand and slide the drive
plate under the microscope. Align the hollow end of the drive shaft bearing so that it will slide over
the drive shaft / gear assembly that you secured to the microscope’s fine focus shaft in step #1. Slide
the drive in so that the drive gear mates with the encoder gear. Push the drive completely onto the
Last update: 2021/09/23 17:15 nikon_eclipse_800_zdrive https://asiimaging.com/docs/nikon_eclipse_800_zdrive
https://asiimaging.com/docs/ Printed on 2022/01/12 17:32
microscope so that the edge of the black base plate is against the side of the microscope. Once the
drive is completely pushed onto the microscope reattach the base clamp that you remove in step #2,
and use the 2.5mm Allen Wrench to tighten the set screw in the base clamp assembly. This will cause
the silver press bar to squeeze against the side of the microscope and hold the drive assembly
securely in place. After the base plate has been secured insure that the gears are properly aligned
and that nothing is binding or rubbing.
Step 4 -Aligning the drive
Turn the left fine focus knob and insure that there is no one spot with in the 360 degrees of rotation
where any drag is felt. If you feel any drag, slightly move the drive along the horizontal ( y axis ) and
vertical ( z axis ) to a point where no drag is felt. Since the drive is usually self aligning little or no
movement in the x and y axis is required. Use the 2.5mm and 7/64” Allen wrenches to tighten the
adjustment screws, that were loosened in step # 2, at a point where no drag is felt. Recheck for
minimum drag on the fine focus shaft by turning the right fine focus shaft. Repeat alignment
procedure if necessary.
Step 5 - Installing the cover & Fine Focus knob
Locate the ASI cover. Place it in position over the motor drive assembly and secure it with the screws
provided. Place the new right fine focus knob over the protruding end of the drive shaft and secure it
in place with the two setscrews in the knob.
This completes the installation of the ASI motor drive onto the Nikon Eclipse 800 microscope.
Connecting the Motor Drive to the Controller and Computer
Please refer to the wiring drawings and diagrams given in the manual
Tools Needed:
Small slotted screwdriver
1) Locate the drive cable. Connect one end of the drive cable to the 9 pin connector on the ASI drive
that is attached to the microscope and the other end to mating connector on the back of the
Controller labeled “Drive.
2) Locate the computer interconnect cable. Connect one end to the mating connector on the back of
the Controller labeled “Serial In”. Connect the other end to the appropriate serial output of your
computer. For an IBM compatible PC this is typically COM1 through
3) Plug in the MFC-2000 power cord.
This completes the steps necessary to interconnect the ASI motor drive. Please refer to the operation
section of the manual before using the MFC-2000 or MS-2000 controller.
2022/01/12 17:32 9/9 Nikon Eclipse 800 Microscope Motor Drive Installation
Applied Scientific Instrumentation - https://asiimaging.com/docs/
nikon, eclipse800, zdrive
From:
https://asiimaging.com/docs/ - Applied Scientific Instrumentation
Permanent link:
https://asiimaging.com/docs/nikon_eclipse_800_zdrive
Last update: 2021/09/23 17:15
Andere Nikon Mikroskop Handbücher
Nikon
Nikon 50i Bedienungsanleitung
Nikon
Nikon ECLIPSE E200 POL Bedienungsanleitung
Nikon
Nikon E800 Bedienungsanleitung
Nikon
Nikon ECLIPSE 80i Bedienungsanleitung
Nikon
Nikon Eclipse TE300 Bedienungsanleitung
Nikon
Nikon Alphapot2 Handbuch
Nikon
Nikon eclipse Ci-S Bedienungsanleitung
Nikon
Nikon SMZ1500 Bedienungsanleitung
Nikon
Nikon Microphot-FXA Bedienungsanleitung
Nikon
Nikon LABOPHOT-POL Bedienungsanleitung
Nikon
Nikon SMZ645 Bedienungsanleitung
Nikon
Nikon Eclipse Ci-E Bedienungsanleitung
Nikon
Nikon Ee1078 Bedienungsanleitung
Nikon
Nikon SC Bedienungsanleitung
Nikon
Nikon Eclipse E400 POL Bedienungsanleitung
Nikon
Nikon SMZ800N Bedienungsanleitung
Nikon
Nikon Eclipse Ni-U Bedienungsanleitung
Nikon
Nikon SMZ460 Bedienungsanleitung
Nikon
Nikon Alphaphot Bedienungsanleitung
Nikon
Nikon Eclipse E400 Bedienungsanleitung
Beliebte Mikroskop Handbücher anderer Marken
Thermo Scientific
Thermo Scientific Nicolet iN10 Leitfaden
National
National DC3-163 Bedienungsanleitung
KERN Optics
KERN Optics OPE-1 Bedienungsanleitung
OPTIKA MICROSCOPES
OPTIKA MICROSCOPES B-150D Bedienungsanleitung
Prior
Prior Lux POL Bedienungsanleitung
Opitec
Opitec Smartscoop 115615 Bedienungsanleitung
VWR
VWR VisiScope 384 Series Bedienungsanleitung
Leica
Leica DI C800 Handbuch
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Bedienungsanleitung
ThermoFisher Scientific
ThermoFisher Scientific Continuµm Bedienungsanleitung
Olympus
Olympus SZ61 Bedienungsanleitung
Leica
Leica FL560 Bedienungsanleitung