Olympus BXC-CBB Bedienungsanleitung

Instructions

BXC-CBB

Modular Microscope Assemblies

Hardware

Notes

This instruction manual is for Modular Microscope Assemblies.

To ensure safety, obtain optimum performance and to familiarize yourself fully

with the use of this product, we recommend that you study this manual thoroughly

before operating this product, and always keep this manual at hand when

operating this product.

Retain this instruction manual in an easily accessible place near the work desk for

future reference.

This product is applied with the requirements of standard IEC/EN61326-1 concerning electromagnetic

compatibility.

- EmissionClass A, applied to industrial environment requirements.

- ImmunityApplied to industrial environment requirements.

Some interference may occur if this product is used in domestic location.

In accordance with European Directive on Waste Electrical and Electronic Equipment, this

symbol indicates that the product must not be disposed of as unsorted municipal waste, but

should be collected separately. Refer to your local our distributor in EU for return and/or

collection systems available in your country.

Research and Industrial Use Only

This product is categorized as FCC Part15 Class A exempt device. Using this product may affect other

equipment in the environment. The operator of this exempted product shall be required to stop

operating the product upon a finding by the Commission or its representative that the product is causing

harmful interference. Operation shall not resume until the condition causing the harmful interference has

been corrected.

For Korea only

Contents

1. Introduction 1

2. Safety precautions 2

2.1 Laser safety 2

2.2 CAUTION:Safety precautions 2

2.3 WARNING:Prevention of electric shock 2

2.4 CAUTION:Electric safety 3

2.5 CAUTION: LED (light emitting diode) 3

2.6 Safety symbols 3

2.7 Caution engraving/label 4

2.8 Specifications 4

2.9 Restrictions 5

3. Setup procedures 6

3.1 Removing the transport lock from the motorized light guide reflected light illuminator 6

3.2 Attaching the motorized light guide reflected light illuminator 6

3.3 Attaching the Autofocus Sensing Unit to the motorized light guide reflected light illuminator 7

3.4 Installing the control box 9

3.5 Setting up BXC-CBB 10

3.6 Setting up BXC-CBE1 12

3.7 Attaching the objectives 12

3.8 Attaching the nosepiece 12

3.9 Storing the motorized nosepiece connector of the motorized light guide reflected light

illuminator 13

3.10 Attaching the light source for reflected light illumination 14

3.10.1 Attaching the LED illumination 14

3.10.2 Attaching the liquid light guide or mercury lamp housing 15

3.10.3 Attaching the motorized reflected filter wheel U-FWR 15

3.10.4 Attaching two lamp housings 17

3.10.5 Attaching the light source for motorized light guide reflected light illuminator with clean lens for AS (BXC-RLI-

LGCA) 17

3.10.6 Attaching a third-party light source 18

3.11 Setting up BXC-FSU 18

3.11.1 Product outline of BXC-FSU 18

3.11.2 User-I/F 19

3.11.3 Adjusting camera diopter 21

3.11.4 Parfocalizing objective lenses 22

3.11.5 Correcting chromatic aberration of the lenses 22

3.12 Connecting cables 23

3.12.1 Connecting a cable to the motorized light guide reflected light illuminator 23

3.12.2 Connecting cables to BXC-CBB 23

3.12.3 Connecting cables to BXC-CBE1 26

4. Operation procedures 27

4.1 Status display of the indicators on BXC-CBB 27

4.2 Status display of the indicators on BXC-CBE1 27

4.3 Adjusting the aperture diaphragm (AS) 28

4.4 Using the interlocked ND filter for BXC-RLI 29

5. Maintenance and Storage 31

5.1 Cleaning of each part 31

6. Troubleshooting 32

6.1 Optical systems 32

6.2 Observation tube 33

6.3 Drive system 33

7. Proper selection of the power supply cord 35

Configuration of instruction manuals

Read all the instruction manuals supplied with the units you purchased.

The following instruction manuals are prepared for the units to be used with this product.

Manual names Main contents

BXC-CBB

Safetymanual

Safety precautions

BXC-CBB

Hardware manual

Safety precautions, specifications and assembly method

BXC-CBB

Application manual

Advanced BXC-FSU Usage. For details, contact us.

BXC-CBB

Command reference manual

How to use RS-232C communication commands. For details, contact us.

Intended use

This product is designed to observe magnified images of specimens in industrial applications.

Appropriate samples include semiconductors, electrical components, molded parts or mechanical parts.

Industrial applications include observation, inspection or measurements.

Do not use this product for any purpose other than its intended use.

1. Introduction

11. Introduction

If the product is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the

product may also be damaged. Always use the product according to this instruction manual.

The following symbols are used in this instruction manual.

CAUTION:

Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury. It may also be

used to alert against unsafe practices or potential material damage.

NOTE:

Indicates a potential situation which, if not avoided, may result in failure of this instrument.

TIP:

Indicates the useful knowledge or information for use.

2.1 Laser safety

CAUTION:

Never peel off the warning label.

Warning label position: Right side surface of BXC-FSU

This product is specified as CLASS 1 laser product.

CLASS 1 LASER PRODUCT (IEC60825-1:2007 / IEC60825-1:2014)

This product complies with 21 CFR 1040.10 and 1040.11 except for conformance with IEC 60825-1 Ed. 3., as described

in Laser Notice No. 56, dated May 8,2019.

Do not remove the cover.

It is very dangerous to remove the cover using a tool as the built-in laser will be accessible. Never remove the cover as it

could also cause failure of the product.

Built-in laser (semiconductor laser)

Wavelength: 780 nm

Maximum power output: 10 mW

Beam divergence: 35°

2.2 CAUTION:Safety precautions

Transportation

When carrying each unit, be careful not to drop it.

If the unit falls, your foot, etc. may get injured.

2.3 WARNING:Prevention of electric shock

Never disassemble any part of this product.

2. Safety precautions

2.1 Laser safety2. Safety precautions

It could cause electric shock or failure of the product.

Do not touch the product with wet hands.

In particular, if you touch the main switch of the power unit or the power cord with wet hands, electric shock, ignition or

failure of the product may be caused.

Do not bend, pull or tie the power cord/cables in a bundle.

Otherwise they could be damaged, causing a fire or an electric shock.

Keep the power cord and cables well away from the lamp housing.

If the power cord and cables contact a hot area of the lamp housing, they could melt and cause electric shock.

2.4 CAUTION:Electric safety

Always use the power cord specified by us.

If the proper AC adapter and the power cord are not used, the electric safety and the EMC (Electromagnetic Compatibility)

performance of the product can not be assured.

Always connect the ground terminal.

Connect the ground terminal of the power cord and that of the power outlet.

If the product is not grounded, our intended electric safety and EMC performance of the product can not be assured.

Do not use the product in close proximity to the sources of strong electromagnetic radiation.

Proper operation may be interfered. The electromagnetic environment should be evaluated prior to operation of the

product.

Disconnect the power cord in case of emergency.

In case of emergency, disconnect the power cord from the power cord connector on the product or from the power outlet.

Install the product at the location where you can reach the power cord connector or the power outlet at hand to

disconnect the power cord quickly. If you cannot install the product at the location described above, check the rated

current of this product and prepare the suitable disconnecting devices.

Do not connect or disconnect the power cord, cables and units while the power is on.

2.5 CAUTION: LED (light emitting diode)

Do not look directly at the light from the LED unit for a long time.

If you feel that the light from LED unit is too bright during observation, adjust the light intensity using the brightness

control knob before continuing the observation. The LED built in this product is basically eye-safe. However, do not look

directly at the light from the LED unit for a long time, since it may cause damage to your eyes.

Do not look directly at the light coming out from the objective or the specular reflection light from the sample.

Do not look directly at the light coming out from the objective for a long time, since it may cause damage to your eyes.

Do not expose your skin to the light coming out from the objective for a long time.

If your skin is exposed to the light coming out from the objective for a long time, you may get burned.

2.6 Safety symbols

The following symbols are placed on this product.

32. Safety precautions 2.4 CAUTION:Electric safety

Study the meaning of the symbol and always use the product in the safest possible manner.

Symbol Meaning

Indicates a non-specific general hazard. Follow the description given after this symbol or in the instruction manual

Indicates that the seesaw type main switch is ON.

(Seesaw type is the type of switch where ON or OFF is selected by pressing it to ON or OFF side.)

Indicates that the seesaw type main switch is ON.

2.7 Caution engraving/label

Safety labels are placed on the portions which particularly require special cautions when using or operating this product.

Be sure to follow these instructions.

Label position Safety label Instructions in the instruction manual Relevant page

(A), (B) [Caution for electric safety]

[Caution for prevention of electric shock]

If a caution engraving or label is dirty or peeled off, contact us for the replacement or other inquiry.

2.8 Specifications

Rating

AC adapter Input:

100-240 V 50/60 Hz 1.4 A(Max)

Output:

24.0 V 2.71 A(Max)

Control box Input:

24V 2.5A(Max)

Operating environment

Temperature 5 to 40°C (41 to 104 °F)

Humidity 0 to 85%

Variation of power supply voltage ± 10 %

Pollution degree 2 (in accordance with IEC60664)

Installation category (excess

voltage category)

II (in accordance with IEC60664)

Conditions for safety standards lIndoor use

lAltitude: Max. 2000 meters

lTemperature: 5 to 40 °C (41 to 104 °F)

lRelative humidity: 20 to 80% for temperatures up to 31 °C (88 °F)

(without condensation) In case of over 31 °C (88 °F), the relative

humidity is decreased linearly through 70% at 34 °C (93 °F), 60% at 37

°C (99 °F), and to 50% at 40 °C (104 °F).

2.7 Caution engraving/label2. Safety precautions

2.9 Restrictions

The maximum total length of the cables (BXC-LCBL1M, BXC-LCBL3M, BXC-LCBL6M) that can be used is 13 m.

52. Safety precautions 2.9 Restrictions

CAUTION:

The use of this product in combination with systems that are not specified in this manual cannot be guaranteed. If you wish

to use this product in combination with systems that are not specified in this manual, take measures under your

responsibility so that the use of this product in combination with systems you will use complies with standards required in

your local area.

3.1 Removing the transport lock from the motorized light guide reflected light illuminator

1. Place BXC-RLI/BXC-RLI-CA/BXC-RLI-LGCA facing down on a desk and remove the transport lock.

NOTE:

lA nosepiece cannot be attached unless the transport lock is removed.

lIf you start the device with the transport lock attached, the product may be damaged.

3.2 Attaching the motorized light guide reflected light illuminator

1. Remove the caps of BXC-RLI/BXC-RLI-CA/BXC-RLI-LGCA (four positions) with your tweezers, etc.

The following steps are described using only BXC-RLI.

2. While making BXC-RLI contact with your instrument from the front to the back (in arrow direction), tighten the

clamping screws (four positions) provided with BXC-RLI.

3. Setup procedures

3.1 Removing the transport lock from the motorized light3. Setup procedures

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus CX22LED Bedienungsanleitung

Olympus

Olympus BHTU-112 Bedienungsanleitung

Olympus

Olympus BXFMA Bedienungsanleitung

Olympus

Olympus Pom Bedienungsanleitung

Olympus

Olympus KHC Bedienungsanleitung

Olympus

Olympus fsx100 Bedienungsanleitung

Olympus

Olympus MIC-D Betriebsanleitung

Olympus

Olympus CX43-RFAB Bedienungsanleitung

Olympus

Olympus VS110 Fluorescence Bedienungsanleitung

Olympus

Olympus U-FWT Bedienungsanleitung

Olympus

Olympus VM Series Bedienungsanleitung

Olympus

Olympus BX3M-CB Bedienungsanleitung

Olympus

Olympus VMF Bedienungsanleitung

Olympus

Olympus CKX31 Betriebsanleitung

Olympus

Olympus ORBEYE Handbuch

Olympus

Olympus VANOX Bedienungsanleitung

Olympus

Olympus BH2-5RE Montageanleitung

Olympus

Olympus FV5-LD405 Bedienungsanleitung

Olympus

Olympus BH2 Series Montageanleitung

Olympus

Olympus BX3-URA Bedienungsanleitung

Olympus

Olympus CK40M FRAME Betriebsanleitung

Olympus

Olympus CHD Bedienungsanleitung

Olympus

Olympus U-DA Bedienungsanleitung

Olympus

Olympus FHT-521 Bedienungsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung