Olympus U-MDOB3 Bedienungsanleitung

Instructions

This instruction manual is for Olympus discussion attachments.

To ensure safety, obtain optimum performance and to familiarize yourself fully with the use

of this product, we recommend that you study this manual thoroughly before operating this

product, and always keep this manual at hand when operating this product.

Retain this instruction manual in an easily accessible place near the work desk for future

reference.

For details of products included in the configuration of this system, see page 7 and 10 of this

instruction manual.

Discussion attachments

Optical microscope accessory

For 2, 5, 9, 10 and 13 persons

In accordance with European Directive on Waste Electrical and Electronic Equipment, this

symbol indicates that the product must not be disposed of as unsorted municipal waste, but

should be collected separately.

Refer to your local Olympus distributor in EU for return and/or collection systems available in

your country.

This product is applied with the requirements of standard IEC/EN61326-1 concerning

electromagnetic compatibility.

- Immunity Applied to industrial and basic environment requirements.

NOTE: This product has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the product is operated in a commercial environment. This product

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instruction manual, may cause harmful interference to radio communications.

Operation of this product in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the product.

Introduction....................................................................................................................................................... 1

Safety precautions

...................................................................................................................................... 2

1 Configuration of the discussion system and orientation of observed images ......5

2 Nomenclature of units and functions................................................................................... 7

3 Operation

.....................................................................................................................................................1

3-1 Using the stray light prevention cover..........................................................................................11

3-2 Diopter adjustment........................................................................................................................................11

1Diopter adjustment of main observer...................................................................................................................... 11

2Diopter adjustment of assistant observer............................................................................................................ 12

3-3 Pointer operation .............................................................................................................................................13

1Adjusting the pointer brightness..................................................................................................................................13

2Selecting the pointer color ................................................................................................................................................ 13

3Moving the pointer.................................................................................................................................................................... 13

3-4 Notes for image acquisition ..................................................................................................................14

4 Specifications...........................................................................................................................................15

5 Assembly......................................................................................................................................................16

5-1 Face to face observation system for 2 persons..................................................................16

1Attaching the observation attachment body.....................................................................................................16

5-2

Side by side observation system for 2 persons and system for 5 persons............. 17

1Attaching the observation attachment body..................................................................................................... 17

2Attaching the stand.................................................................................................................................................................. 18

3Attaching the side viewer ................................................................................................................................................... 19

4Attaching the observation tube..................................................................................................................................... 19

5Attaching the eyepiece.........................................................................................................................................................20

6Adjusting the stand height.................................................................................................................................................21

Contents

5-3 System for 9 persons..................................................................................................................................22

1Attaching U-MDOB3 ................................................................................................................................................................22

2Attaching the stand..................................................................................................................................................................22

3Attaching U-MDOSV.................................................................................................................................................................22

4Attaching BX3-MDOE .............................................................................................................................................................23

5Attaching the stand..................................................................................................................................................................23

6Attaching U-MDOSV.................................................................................................................................................................24

7Attaching the observation tube.....................................................................................................................................24

8Attaching the eyepiece.........................................................................................................................................................25

9Adjusting the stand height.................................................................................................................................................25

5-4 System for 10 persons...............................................................................................................................26

1Attaching the stand..................................................................................................................................................................26

2Attaching U-MDO10R3 ..........................................................................................................................................................26

3Attaching the light path split unit.................................................................................................................................27

4Attaching U-MDO10B3 ..........................................................................................................................................................27

5Attaching the stand..................................................................................................................................................................27

6Attaching U-MDOSV.................................................................................................................................................................27

7Attaching the observation tube.....................................................................................................................................28

8Attaching the eyepiece.........................................................................................................................................................28

9Adjusting the stand height.................................................................................................................................................28

5-5 Extending to the system for 13 persons.................................................................................... 29

5-6 Attaching other units................................................................................................................................... 30

1Connecting the AC adapter..............................................................................................................................................30

2Attaching the cord stopper................................................................................................................................................31

3Attaching the heat protection shield (Option) ..................................................................................................31

Proper selection of the power supply cord...............................................................32

Introduction

Instruction manual

This document is an instruction manual for discussion attachment. Read the instruction manual for microscope

together with this instruction manual.

This system is a discussion attachment used together with the BX series microscope.

Eyepieces, objectives or condensers, etc. used together with this system should be applied to UIS2 (or UIS) optical

system series.

Safety precautions

CAUTION - Electric safety -

Always use the power cord provided by Olympus.

If the proper AC adapter and the power cord are not used, the electric safety and the EMC (Electro-Magnetic

Compatibility) performance of the product cannot be assured. If no power cord is provided, please select the proper

power cord by referring to the section “Proper selection of the power cord” at the end of this instruction manual.

Always connect the ground terminal.

Connect the ground terminal of the power cord and that of the power outlet. If the product is not grounded, our

intended electric safety and EMC performance of the product cannot be assured.

Do not use the product in close proximity to the sources of strong electromagnetic radiation.

Proper operation may be interfered. The electromagnetic environment should be evaluated prior to operation of the

product.

Disconnect the power cord in case of emergency.

In case of emergency, be sure to unplug the power cord from the power cord connector on the product or from the

wall power outlet. Install the product at the location where you can reach the power cord connector or the power outlet

at hand to disconnect the power cord quickly.

Do not connect or disconnect the power cord, cables and units while the power is on.

CAUTION - Installation of the product -

Install the product on a sturdy and level desk.

With this system, the product is installed on the multiple desks which are arranged side by side. All desks must be

sturdy and level. Also, take proper measures to fix the desks to avoid them from moving.

If the product is used in a manner not specified by this manual, the safety of the user may be imperiled. In addition, the

product may also be damaged. In addition, the product may also be damaged. Always use the product according to this

instruction manual.

The following symbols are used in this instruction manual.

CAUTION : Indicates a potentially hazardous situation which, if not avoided, may result in

minor or moderate injury.

NOTE

: Indicates a potentially hazardous situation which, if not avoided, may result in

damage to the product or other property and/or may cause problems.

TIP

: Indicates the useful knowledge or information for use.

CAUTION - Prevention of electric shock -

Keep the power cord and cables well away from the lamp housing.

If the power cord and cables contact a hot area of the lamp housing, they could melt and cause electric shock.

Do not touch the product with wet hands.

In particular, if you touch the main switch of the power unit or the power cord with a wet hand, electric shock, ignition

or failure of the product may be caused.

The following symbols are placed on this product.

Study the meaning of the symbols and always use the product in the safest possible manner.

Symbols Meaning

Supply DC current (from the provided AC adapter).

Indicates an input jack.

Indicates a pointer.

CAUTION - Safety symbols -

1. Do not leave stains or fingerprints on the lenses or filters. If they get dirty, blow away dust with a commercially

available blower and gently wipe the lens or filter with a piece of cleaning paper (or clean gauze).

Only when cleaning fingerprints and oil stains, slightly moisten a piece of cleaning paper with commercially

available absolute alcohol and wipe them off with it.

Since the absolute alcohol is highly flammable, it must be handled carefully. Be sure to keep it away

from open flames or potential sources of electrical sparks. For example, the electrical equipment that

is switched on and off may cause the ignition of a fire. Also, always use the absolute alcohol only in a

well-ventilated room.

CAUTION

·This product is a precision instrument. Handle it with care and avoid subjecting it to a sudden or

severe impact.

·Never disassemble any part of the product. Otherwise, failure may result.

·Do not use the product in areas where it may be subjected to direct sunlight, high temperature and/or

humidity, dust or vibrations.

For the conditions of operating environments, see "4 Specifications" (page 15).

1. If this system is combined with a super widefield eyepiece, the pointer cannot be moved around the entire range of

the field of view. Also, a ghost of the pointer may be observed.

2. If the eyepiece is equipped with a micrometer, a ghost of the pointer may be observed.

3. To prevent the stray light:

· Cover the eyepieces which are not used by the assistant observers with the provided stray light prevention

covers (page 11, page 14).

· Make sure to attach caps to the unused tube mounts and side viewer mounts.

4. T

o ensure safety, disconnect the power plug of the AC adapter from the power outlet after use.

5. Using the provided cord stopper (page 31), place the AC adapter cord at the position where it does not come in the

way of microscope operation and take care not to bring the cord in contact with the lamp housing.

6. If the reflected light illuminator is combined, these observation attachments cannot be combined.

NOTE

Handling Precautions

Maintenance and storage

2. Wipe the portions other than lenses with a dry soft cloth. If the dirt cannot be removed by dry-wiping, moisten a soft

cloth with diluted neutral detergent and wipe the dirty surface with it.

Do not use the organic solvents because they may deteriorate the coated surface or plastic parts.

3. After using this product, set the main switch to (OFF), wait until the lamp housing is cooled down sufficiently, and

keep it covered with a dust cover during storage.

4. When disposing of this product, follow the regulations and rules of your local government. Contact Olympus for any

questions.

NOTE

1 Configuration of the discussion system and orientation of observed images

The following illustration shows the top view of the discussion system.

expresses the orientation of the line of sight of the observer.

expresses the orientation of the image observed through each eyepieces.

If the observation tubes are not attached in the orientation as shown in the illustration, the orientation of the

image rotates.

TIP

Assistant

observer

Main

observer

Face to face observation

system for 2 persons

Main

observer

Assistant

observer

Side by side observation

system for 2 persons

Main

observer

Assistant

observer

Assistant

observer

System for 5 persons

Main

observer

Assistant

observer

Assistant

observer

Assistant

observer

Assistant

observer

System for 9 persons

Main

observer

Assistant

observer

Assistant

observer

Assistant

observer

Assistant

observer

System for 10 persons

Main

observer

Assistant

observer

Assistant

observer

Assistant

observer

Assistant

observer

Assistant

observer

Assistant

observer

Assistant

observer

Assistant

observer

System for 13 persons

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Olympus Mikroskop Handbücher

Olympus

Olympus BHS Bedienungsanleitung

Olympus

Olympus BHT-111 Bedienungsanleitung

Olympus

Olympus IX81 Bedienungsanleitung

Olympus

Olympus U-DA Bedienungsanleitung

Olympus

Olympus IX2-DSU Bedienungsanleitung

Olympus

Olympus BX41 Bedienungsanleitung

Olympus

Olympus GX53 Bedienungsanleitung

Olympus

Olympus DP21-SAL Benutzerhandbuch

Olympus

Olympus Fluoview FV1000 Handbuch

Olympus

Olympus K Betriebsanleitung

Olympus

Olympus U-D7RES Bedienungsanleitung

Olympus

Olympus CX41 Bedienungsanleitung

Olympus

Olympus CKX41 Bedienungsanleitung

Olympus

Olympus BX51-P Betriebsanleitung

Olympus

Olympus CX43-RFAB Bedienungsanleitung

Olympus

Olympus BXC-CBB Bedienungsanleitung

Olympus

Olympus BX46 Bedienungsanleitung

Olympus

Olympus Fluoview FV1000 Bedienungsanleitung

Olympus

Olympus Pom Bedienungsanleitung

Olympus

Olympus BX3M-CB Bedienungsanleitung

Olympus

Olympus BX51-P Bedienungsanleitung

Olympus

Olympus BX-RFAA Bedienungsanleitung

Olympus

Olympus SZX-AR1 Referenzhandbuch

Olympus

Olympus BH2 Series Montageanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Leica

Leica FL560 Bedienungsanleitung