Precor Resolute RSL 414 Bedienungsanleitung

ENGLISH

Resolute™ Strength Selectorized Line

Converging Chest Press RSL 414

Assembly Guide

Assembly Requirements

It takes about 90 minutes to assemble this equipment. If this is your rst time doing this, allow more time.

CAUTION

At least two people are required to assemble the equipment. DO NOT attempt to assemble this by yourself. Precor recommends that all strength equipment be bolted to the

ooring at all anchoring points.

Installation Requirements

● Unpack the boxes and assemble the equipment close to where you plan to use it.

● Locate equipment at least 40 inches (1 meter) away from any walls, furniture, or objects on all sides.

● While tightening the fasteners, be sure to leave room for adjustments. DO NOT fully tighten fasteners until instructed to do so.

● Set up and assemble the equipment on a solid, at surface, so that it remains level and stable.

● DO NOT move the equipment without assistance.

Required Tools

● Torque wrench with torque range to at least 150 ft-lb (206 N-m) and ts the following hex bits: 6, 8, and 10 mm

● Socket wrench sets, metric and standard, plus extensions

● Open-end wrench sets, metric and standard

● Hex wrench sets, metric and standard, plus extensions

●Box cutter

●Rubber mallet

● Retaining ring pliers - large, medium, and small

● Pliers - large, medium, and small

Trademarks

Resolute is a trademark and Precor is a registered trademark of Precor, Incorporated.

All other trademarks belong to their respective owners.

Part # Name Quantity Part # Name Quantity

Main frame 1 Weight plates 10 lb (4.5 kg) 23

Side arm, left 1 Collars 2

Side arm, right 1End plugs with sleeves 2

Upper cross brace 1 Washers, 12.2 mm ID x 35 mm OD 2

Lower cross brace 1Washers, domed, silver 2

Seat assembly 1 Washers, rubber, black 3

Shaft 1 Washer, silver 13.5 mm ID x 35 mm OD 1

Roller assembly 1 Retaining rings, 3/4-inch 2

Gas spring 1 Hole plugs 2

Bumpers 4 Button head cap screw (BHCS) M6 x 15 mm 1

Weight stack spacer, 1-inch 1Socket head cap screws (SHCS) M12 x 25 mm 2

Add-on weight 5 lb (2.2 kg) 1Washers, 9 mm 6

Weight stack tower frame 1Washers, 13 mm 8

Kick plate 1 Hex head screws 5/16-inch x 1½-inch 6

Add-on weight handle 1Socket head cap screws (SHCS) M12 x 35 mm 6

Top plate assembly 1Socket head cap screws (SHCS) M12 x 130 mm 2

Shroud, crown 1Nylon lock nuts, M12 2

Guide rods 2 Socket head cap screws (SHCS) M10 x 65 mm 2

Guide rod with cap 1Nylon lock nuts, M10 2

Add-on weight spacer, 3-inch 1Button head cap screws (BHCS) M10 x 125 mm 2

Shroud, rear middle 1Socket head cap screws (SHCS) M10 x 40 mm 2

Shroud, rear lower 1Washers, 11 mm 5

Shroud, rear upper 1 Back pad 1

Shroud, top tray 1 Seat pad 1

Shroud, front middle (left and right) 2 Weight labels 1

Shroud, front lower 1Roller adjustment tool (attached to Seat assembly) 1

Shroud, front upper placard 1

Shroud, pulley cover 1

Parts List

Frame Assembly

DO NOT tighten fasteners until instructed to do so.

Have your assistant hold frame parts in place during assembly.

Image Hardware Instructions

12 M12 x 130 mm SHCS

4 washers, 13 mm

2 M12 nylon lock nuts

Tools: Hex wrench, 10 mm

Socket wrench, 19 mm

2 M10 x 125 mm BHCS

1 washer, 11 mm

Connect lower cross brace to weight stack tower and

kick plate .

Align to second hole from right.

Insert guide rod fasteners, one from each side, to align the

kick plate. Hand tighten only. These will be removed tem-

porarily in a later step.

50 48

2 2 M12 x 35 mm SHCS

2 washers, 13 mm

Tool: Hex wrench, 10 mm

Connect lower cross brace to main frame .

32 M12 x 35 mm SHCS

2 washers, domed, silver

Tool: Hex wrench, 10 mm

Connect upper cross brace to weight stack tower .

42 M12 x 35 mm SHCS

2 washers, 13 mm

Tool: Hex wrench, 10 mm

Connect upper cross brace to main frame .

5 Tools: Hex wrench, 10 mm

Socket wrench, 19 mm

Torque wrench

Gently rock the frame to align. Tighten all M12 fasteners to

55 ft-lb (75 N-m) of torque.

Do not tighten the M10 screws installed in step 1 at this

time. They will be removed temporarily in a later step.

Moving Parts

Image Hardware Instructions

12 collars Slide collars onto arm shafts on main frame. Ensure at sides of

collars are towards main frame.

2Slide left arm and right arm onto shafts at top of main

frame . Each arm is labeled with and . Match the arm

labels with the labels at the top of the main frame to ensure prop-

er placement.

32 washers, rubber

2 washers, 12.2 mm ID x 35 mm OD

2 M12 x 25 mm SHCS

Tools: Hex wrench, 10 mm

Torque wrench

Slide washers on to each arm in order shown. Hold washers

centered in arms and secure. Tighten to a torque of 55 ft-lb (75

N-m).

42 end plugs with sleeves

Tool: Mallet

Slide end plugs with sleeves onto ends of arms. Tap gently with

mallet if needed.

Remove all and labels.

34 32

Seat Assembly

Image Hardware Instructions

1 1 roller assembly

1 shaft

2 retaining rings, 3/4-inch

Tool: Pliers

Attach the seat assembly to the main frame . Place the roller assembly

between the seat assembly brackets and insert the shaft. Secure each side with

retaining rings.

21 gas spring Snap gas spring into place under seat and at base of main frame . The larg-

er body of the gas spring attaches to the seat.

3To adjust the roller clearance on the seat assembly, have your assistant apply

downward force on seat.

4Tools: Two hex wrenches, 8 mm Preinstalled on the front roller of the seat assembly is a roller adjustment tool .

Continue to apply force to the seat assembly and press the adjustment tool down-

ward to turn the roller. Turn until it just contacts the plastic ratchet plate and no

more than 180 degrees. Tighten the socket head screws on the sides of the front

roller (ensure the position of the roller tool does not change). Remove tool.

5 4 hex head screws 5/16 x 1½-inch

4 washers, 9 mm

Tool: Socket wrench, ½-inch with extension

Attach seat pad to seat assembly .

Route the Cable

Image Hardware Instructions

1Tools: Two open end wrenches, 19 mm

Torque wrench

Attach cable to arms. Thread cable end into rod end as shown. Hold rod end with

wrench and fully tighten lock nut. Maximum distance is 25 mm.

Tighten to 50 ft-lb (67.7 N-m).

2 Tools: Socket wrench, 8 mm

Socket wrench, 4 mm

To route the cable around the lower pulley on the weight stack tower, remove

the cable retainer. Route the cable around the pulley and then replace the cable

retainer.

3Tools: Hex wrench, 8 mm

Open-end wrench, 19 mm

Torque wrench

To route the cable to the upper pulleys of weight stack tower, remove the cable

retainers, route the cables, and replace the retainers. Tighten to 50 ft-lb (67

N-m) of torque.

6 2 hex head screws 5/16 x 1½-inch

2 washers, 9 mm

2 hole plugs

Tool: Socket wrench, ½-inch with extension

Attach back pad to main frame .

Finish the Weight Stack Tower

Image Hardware Instructions

12 M10 x 125 mm BHCS

1 washer, 11 mm

Tool: Hex wrench, 6 mm

Remove the guide rod fasteners installed in step 1 of the Frame Assembly.

2 1 weight stack spacer, 1-inch

2 guide rods

Align the weight stack spacer over the holes on the base of the tower. Insert two

weight guide rods and lean outwards about 6 inches (15 cm), enough clearance

for the weights. Flat side of weight stack spacer should face user side.

32 bumpers

23 10 lb (4.5 kg) weight plates

1 top plate assembly

Slide one bumper on to each rod. Place the weight plates on the rods. Ensure the

side with three holes face the user side and single hole to the back. Place the top

plate over the weight plates. The plates and top plate should align ush on the

user side.

50 48

Andere Handbücher für Resolute RSL 414

Inhaltsverzeichnis

Andere Precor Ellipsentrainer Handbücher

Precor

Precor HANDBOEK EFX 556i Montage- und Bedienungsanleitung

Precor

Precor Resolute RSL 605 Bedienungsanleitung

Precor

Precor Precision 400 Series Bedienungsanleitung

Precor

Precor Resolute RSL 602 Bedienungsanleitung

Precor

Precor EFX 5.17i Bedienungsanleitung

Precor

Precor EFX 5.33 Bedienungsanleitung

Precor

Precor 5.31 Bedienungsanleitung

Precor

Precor Elliptical Fitness Crosstrainer Experience 700... Bedienungsanleitung

Precor

Precor EFX 524I Bedienungsanleitung

Precor

Precor Experience Sereis Bedienungsanleitung

Precor

Precor EFX 883 Montageanleitung

Precor

Precor PRECISIONSERIES Technisches Handbuch

Precor

Precor HANDBOEK EFX 556i Bedienungsanleitung

Precor

Precor C554i Bedienungsanleitung

Precor

Precor Discovery DSL 621 Bedienungsanleitung

Precor

Precor EFX Series Bedienungsanleitung

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.25 Bedienungsanleitung

Precor

Precor EFX 825 Bedienungsanleitung

Precor

Precor ELLIPTICAL FITNESS CROSSTRAINERS EFX 835 Montageanleitung

Precor

Precor Resolute RSL 620 Bedienungsanleitung

Precor

Precor EFX 835 Montageanleitung

Precor

Precor Resolute RSL 208 Bedienungsanleitung

Precor

Precor EFX524 Bedienungsanleitung

Precor

Precor Resolute RSL 606 Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

NordicTrack

NordicTrack E 9.2 Elliptical Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung

Reebok

Reebok 1000 Zx Elliptical Bedienungsanleitung