Precor Discovery Series Bedienungsanleitung

Discovery™ Series Plate Loaded

624 SQUAT MACHINE ASSEMBLY GUIDE

Hardware kit

Hardware Hardware Name Quantity

Socket head cap bolt (M12 × 35 mm) 10

Flat washer (13 x 26 mm) 12

Socket head cap bolt (M12 × 25 mm) 6

Socket head cap bolt (M12 × 75 mm) 2

Set Screws (M8 x 6 mm) 4

Flat washer (11 x 23 mm) black 6

Flat washer (12.2 x 30 mm) 6

End Cap 4

Button head cap bolt (M8 x 15 mm) 5

Flat head bolt (M12 × 30 mm) 4

Hex key (8 mm) 2

Hex key (10 mm) 1

Flat head hex screw (M8 x 20 mm) 6

Flat head hex bolt (M12 x 70 mm) 2

Button head bolt (M10 x 25 mm)

black 6

Socket head bolt (M8 x 25 mm) 2

Flat washer (9 x 16 mm) 7

TPU (rubber bumper) washer 4

Button head bolt (M10x16 mm) 2

Flat washer (M10 x 20 mm) 2

Assembly requirements

Precor recommends at least two people for this installation.

DO NOT attempt assembly by yourself.

When assembling the equipment, we recommend you:

lFollow the steps in the order listed in this assembly guide.

lUnpack the box and assemble the equipment close to where you plan to use it.

lLocate the equipment at least 40 inches (1 meter) away from walls or furniture on either

side of the equipment, and 40 inches (1 meter) away from objects behind or in front of the

equipment.

lAssemble the equipment on a solid, flat surface, so that it remains level and stable.

Required tools

lTorque wrench

l18 mm open-end wrench

lRubber mallet

l19 mm open-end wrench

Begin Assembly

NOTE DO NOT fully tighten the fasteners until instructed to do so.

Remove shoulder pad pivot support

Disconnect the pre-assembled shoulder pad assemblies (Figure 1).

Figure 1

Assemble the frame

1. Place the base frame on the floor where you plan to

use the equipment.

2. Attach the rear upright to the base frame using four

bolts and washers (Figure 2).

Figure 2

4. Attach the center frame to the base frame using two bolts and washers and to the

rear upright using two bolts and washers. Fully tighten all bolts.

5. In the center frame bracket, position the

shoulder frame support pivot to align the

bracket and frame openings. Slide the short

axle through the base of the shoulder frame

support and attach the shoulder frame support

using two bolts and two end caps (Figure

3). Figure 3

NOTE The axle should slide easily through the openings. If it does

not, use a rubber mallet to gently tap it through the opening.

Attach moving arms

1. Position the weight arm pivot tube in line with the bottom holes in the rear upright

bracket. Ask your assistant to hold it level while you slide the axle with the center groove

through the bracket and secure it using two bolts and two washers .

2. Position the cable arm pivot tube and long-

stemmed rubber bumpers in line with the

middle holes in rear upright bracket. Ask your

assistant to hold it level while you slide the axle

through the bracket and secure it using two

bolts and two washers .

3. Position the shoulder frame pivot tube and

short-stemmed rubber bumpers in line with the

top holes in the rear upright bracket. Ask your

assistant to hold it level while you slide the axle

through the bracket and secure it using two

bolts and two washers . Figure 4

3. Fully tighten all bolts to 65 ft-lb (88 N-m).

Attach shoulder frame

1. Slide the shoulder pad assembly tube onto the shaft (Fig-

ure 5).

2. Secure it using one bolt and one end cap (Figure 5).

3. Repeat Steps 1 and 2 to attach the other shoulder pad

assembly tube. Fully tighten the bolts.

4. Reconnect the shoulder pad assembly back through the

rod end (Figure 5).

5. Ensure the shoulder pad assemblies are aligned with

each other. If they are not, adjust the rod end length as

necessary. Figure 5

6. Once aligned, place the arm on the Safety Stop. Center the rod end in a rotational manner,

while preventing the rod end from turning, tighten the jam nut.

Not centered Centered

Figure 6 Figure 7

7. Repeat step 4 to attach the other shoulder pad assembly.

Test each moving arm to make sure it moves smoothly

through its range of motion.

8. Attach each shoulder pad using three screws and wash-

ers (Figure 8). Fully tighten the bolts.

Figure 8

Attach placards

1. Attach the long placard using four bolts and four wash-

ers (Figure 9). Fully tighten the bolts.

Figure 9

2. Attach the short placard by sliding it onto the placard

holder and secure it with one bolt and one washer

(Figure 10). Fully tighten the bolts

Figure 10

Assemble height calibration

1. Place a bumper on either side of the height

adjustment assembly bottom rod end and pos-

ition it inside of the weight arm bracket (Figure

11).

Figure 11

2. Slide the selector tube pin through the brack-

ets, bumpers , rod end, and secure it with the

bolt and washer .

3. Repeat steps 1 and 2 to attach the height adjust-

ment assembly top rod end to the shoulder

frame (Figure 12).

Figure 12

Check height calibration

1. Unload the shoulder frame by lifting it slightly. When the release handle is depressed, the

pop pin should release. Ensure this happens at each height adjustment position.

a. If the pop pin does not release in all positions, loosen the jam nut and turn the

adjustment nut counter clockwise, ½ turn (Figure 13). Then tighten the jam nut

and retest.

b. Continue this process until the pop pin releases at all heights when the load is

removed from the shoulder frame.

2. Remove all weights and lift the weightless shoulder frame. Depress the release handle.

The pop pin should not release with this load.

a. If the pop pin releases the weight arm, loosen the

jam nut and turn the adjustment nut clock-

wise, ½ turn (Figure 13). Then tighten the jam nut

and retest.

NOTE In rare cases, it may be necessary to

adjust the nut in ¼ turn increments to

meet both retest checks.

Figure 13

Attach foot plate

1. Position the foot plate onto the base frame.

2. Secure the plate using two bolts (Figure 14). Fully

tighten the bolts.

Figure 14

Attach weights arm horns

1. Slide the weight horn through the

bumper and into the weight arm (Figure

15).

2. Position the second bumper against the

inside of the weight arm and attach the

horn using one bolt . Fully tighten the

bolts. Figure 15

Attach counter weights

1. Slide the counter weight into the back of the

shoulder frame and secure it use two bolts and

washers (Figure 16). Fully tighten the bolts.

Figure 16

Attach weights storage horns

1. Insert the weight horn into the hole in the rear

upright frame until it stops (Figure 17).

2. Secure the weight horn using a bolt and

washer .

3. Place a set screw into the horn assembly and

tighten.

Figure 17

4. Push the storage horn bumper into the weight horn with its wide side facing outward. If

needed, use a weight plate to push the bumper against the equipment frame.

5. Repeat this procedure to attach the other weight horns.

Stabilize equipment

Once you have assembled the equipment, test its stability by pushing down on each corner. If the

base frame rocks or wobbles, you need to adjust the feet to stabilize it.

1. Locate the round, adjustable feet on the bottom of the equipment frame.

2. Using a 19 mm open-end wrench, turn the positioning bolt to the left or right to level the

equipment.

To move the adjustable foot ... Then turn the bolt ...

Upward To the right

Downward To the left

3. Continue to test the corners of the equipment and readjust the feet as needed.

4. When the equipment is stable, re-tighten the jam

nut with an 18 mm open-end wrench to 600 in-lb

(67.79 N-m).

5. Insert the frame end cap and secure it using two

M6 × 60 mm socket head cap screws. Tighten the

screws to 10 in-lb (1.12 N-m) of torque (Figure

18).

Bolt equipment to floor

Precor recommends that the strength equipment be bolted down at all

anchoring points. Bolting is made possible by removing the end caps at

the frame base and exposing the mounting holes that accommodate the

bolts (see the accompanying figure). Replace end caps when bolting is

complete.

NOTE As floor materials vary, it is important that you consult a licensed contractor

to advise you on proper bolting techniques and appropriate fastener types.

CAUTION Standards occasionally change or are updated. Precor recommends

that you keep apprised of your local industry standards. Precor shall not be held

liable for failure to properly bolt the strength equipment to the floor.

Andere Handbücher für Discovery Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Precor Ellipsentrainer Handbücher

Precor

Precor Resolute RSL 314 Bedienungsanleitung

Precor

Precor Resolute RSL 324 Betriebsanleitung

Precor

Precor Experience Series Bedienungsanleitung

Precor

Precor Resolute RSL 515 Bedienungsanleitung

Precor

Precor Resolute RSL 324 Bedienungsanleitung

Precor

Precor Experience Series 800 line EFX Bedienungsanleitung

Precor

Precor Experience EFX 556i Bedienungsanleitung

Precor

Precor EFX 5.21i Bedienungsanleitung

Precor

Precor PRECISION SERIES Bedienungsanleitung

Precor

Precor AMT Series Bedienungsanleitung

Precor

Precor Resolute RSL 313 Bedienungsanleitung

Precor

Precor C524 Bedienungsanleitung

Precor

Precor C556 Bedienungsanleitung

Precor

Precor Resolute RSL 414 Bedienungsanleitung

Precor

Precor 5.31 Bedienungsanleitung

Precor

Precor Resolute RSL 605 Bedienungsanleitung

Precor

Precor Resolute RSL 215 Bedienungsanleitung

Precor

Precor EFX 600 Line Bedienungsanleitung

Precor

Precor C546 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Precor

Precor Resolute RSL 414 Bedienungsanleitung

Precor

Precor Elliptical Fitness Crosstrainer EFX 5.25 Bedienungsanleitung

Precor

Precor Experience EFX 700 SERIES Bedienungsanleitung

Precor

Precor EFX 576i Bedienungsanleitung

Beliebte Ellipsentrainer Handbücher anderer Marken

Weslo

Weslo Momentum 4.0 Elliptical Bedienungs- und Wartungshandbuch

Progear Fitness

Progear Fitness Air elliptical pro 1307 Bedienungsanleitung

Torque Fitness

Torque Fitness XPLLP Bedienungsanleitung

Octane Fitness

Octane Fitness PRO3700C Bedienungsanleitung

Xterra

Xterra FS5.8e Bedienungsanleitung

Bodyguard

Bodyguard E-40 Bedienungsanleitung

Bonn Germany

Bonn Germany Concept 2.2 Bedienungsanleitung

NordicTrack

NordicTrack E 9.2 Elliptical Bedienungsanleitung

Vision Fitness

Vision Fitness X6600iNetTV Bedienungsanleitung

Matrix

Matrix MX-A5x Bedienungsanleitung

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Bedienungsanleitung

Sears

Sears FREE SPIRIT C249 30737 0 Bedienungsanleitung

True

True FS-64 Bedienungsanleitung

Sport-thieme

Sport-thieme ST 310 Bedienungsanleitung

VIRTUFIT

VIRTUFIT CTR 1.1 Bedienungsanleitung

Kettler

Kettler GIRO C 1 Bedienungsanleitung

CIRCLE FITNESS

CIRCLE FITNESS E7 Bedienungsanleitung

Reebok

Reebok 1000 Zx Elliptical Bedienungsanleitung