Radio Shack ET-1124 Bedienungsanleitung

Cat. No. 43-1124

OWNER’S MANUAL

Please read before using this equipment.

ET-1124

900 MHz Digital Spread Spectrum

Cordless Phone

FEATURES

Your RadioShack ET-1124 900 MHz

Digital Spread Spectrum Cordless Tele-

phone uses advanced cordless tele-

phone technology to give you superior

audio quality and extended range. Its

headset jack lets you connect an option-

al headset for hands-free convenience.

The phone’s other features include:

Spread Spectrum Technology —

spreads the signal across several fre-

quencies, providing additional security

for your phone conversations.

900 MHz — provides longer range and

less interference than many other cord-

less phones.

10 Channels—automatically selects a

clear channel when you make or answer

a call. You can also manually change

channels during a call.

10-Number Memory Dialing — lets you

store 10 numbers in memory for easy di-

aling.

Page — lets you send a signal from the

base to the handset to page someone or

to help you locate the handset if you

have misplaced it.

Volume Control — lets you adjust the

volume you hear through the handset.

Programmable Ringer — choose from

four tone/volume settings for the hand-

set’s ringer.

Ample Talk and Standby Time — the

supplied battery (when fully charged)

provides about 3.5 hours of talk time or

7 days of standby time.

Security Access-Protection Code —

prevents other cordless phone users

from using your phone line while the

handset is off the base.

Redial — lets you quickly dial the last

number dialed.

Flash — sends an electronic switch-

hook signal for use with special phone

services, such as Call Waiting.

Tone or Pulse Dialing — lets you use

your phone with tone or pulse (rotary) di-

aling and lets you switch from pulse to

tone dialing for long-distance, bank-by-

phone, or other special services.

Hearing-Aid Compatibility — lets you

use your phone with hearing aids that

have T (telephone) switch.

This telephone has been tested and

found to comply with all applicable UL

and FCC standards.

RadioShack is a registered trademark used by Tandy Corporation.

Important:

• Cordless phones such as this one

require AC power to operate. When

the AC power is off, you cannot dial

out or receive incoming calls using

your phone. To be safe, you should

also have a phone that does not

need AC power to operate (not a

cordless phone) so you can still

make and receive calls if there is an

AC power failure.

• When AC power is lost, the phone

loses the security access-protection

code connection between the base

and the handset. When power is

restored, put the handset on the

base briefly to restore this connec-

tion so you can use the handset.

READ THIS BEFORE

INSTALLATION

We have designed your phone to con-

form to federal regulations and you can

connect it to most phone lines. However,

each device that you connect to the tele-

phone line draws power from the line.

We refer to this power draw as the

phone’s ringer equivalence number, or

REN. The REN is on the bottom of your

phone.

If you use more than one phone or other

device on the line, add up all the RENs.

If the total is more than five (three in ru-

ral areas), your phones might not ring. If

ringer operation is impaired, remove one

of the devices from the line.

FCC STATEMENT

Your telephone complies with Part 68 of

FCC Rules

. Upon request, you must

provide the phone’s FCC registration

number and REN to your telephone

company. These numbers are on the

bottom of the base.

Note: You must not connect your tele-

phone to:

• coin-operated systems

• party-line systems

• most electronic key phone systems

WARNING: To reduce the risk of fire or

shock hazard, do not expose this product to rain

or moisture.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED PERSONNEL.

This symbol is intended to alert

you to the presence of uninsu-

lated dangerous voltage within

the product’s enclosure that might

be of sufficient magnitude to con-

stitute a risk of electric shock. Do

not open the product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are

included in the literature accom-

panying this product.

CONTENTS

Installation ............................................................................................................... 5

Selecting a Location ........................................................................................... 5

On a Desk Top ............................................................................................. 5

On a Wall Plate or Wall ................................................................................ 5

Connecting and Charging the Battery Pack ....................................................... 7

Setting the Dialing Mode .................................................................................... 8

Setting the Ringer’s Tone and Volume ................................................................ 9

Operation ............................................................................................................... 10

Making and Receiving Calls ............................................................................. 10

Selecting the Channel ...................................................................................... 10

Setting the Handset Volume ............................................................................. 10

Using Redial ..................................................................................................... 10

Using Mute ....................................................................................................... 11

Using Flash ....................................................................................................... 11

Using Tone Services on a Pulse Line ............................................................... 11

Paging ............................................................................................................... 11

Memory Dialing ................................................................................................ 12

Storing a Number in Memory ..................................................................... 12

Entering a Pause ........................................................................................ 13

Dialing a Memory Number ......................................................................... 13

Chain-Dialing Service Numbers ................................................................. 13

Testing Stored Emergency Numbers ......................................................... 13

Using a Headset ............................................................................................... 13

Troubleshooting .................................................................................................... 15

Care and Maintenance .......................................................................................... 17

Replacing the Battery Pack .............................................................................. 18

The FCC Wants You to Know ........................................................................... 18

Lightning ........................................................................................................... 19

INSTALLATION

SELECTING A LOCATION

You can place the phone’s base on a

desk top or table, or mount it on a wall.

Select a location that is:

• near an accessible AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,

electrical appliances, metal walls or

filing cabinets, wireless intercoms,

alarms, and room monitors

• away from other cordless phones

The base’s location affects the hand-

set’s range. If you have a choice of sev-

eral locations, try each to see which

provides the best performance.

Caution: The supplied RadioShack AC

adapter was designed specifically for

your phone. Use only the supplied

adapter.

On a Desk Top

Follow these steps when you place the

base on a desk, shelf, or table.

1. Plug one end of the supplied long

modular cord into the TEL LINE jack

on the back of the base.

2. Plug the modular cord’s other end

into a modular phone line jack.

3. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack on

the back of the base.

4. Route the adapter’s cord through

the strain relief slot on the base.

5. Plug the adapter into a standard AC

outlet.

6. Lift the base’s antenna to an upright

position.

On a Wall Plate or Wall

1. Plug one end of the supplied short

modular cord into the TEL LINE jack

on the back of the base as in “On a

Desk Top,” Step 1.

2. Insert the supplied AC adapter’s

barrel plug into the DC IN 9V jack as

in “On a Desk Top,” Step 3.

3. Route the adapter and modular

cords through the grooves on the

bottom of the base.

4. Plug the modular cord’s other end

into the wall plate jack, then align

the base’s keyhole slots with the

wall plate studs and slide the base

downward to secure it.

5. Plug the adapter into a standard AC

outlet.

6. Press and lift out the handset

holder, rotate it 180°, then snap it

back into place so it holds the hand-

set.

7. Lift the base’s antenna to an upright

position.

Note: To mount the phone directly on a

wall, you need two screws (not supplied)

with heads that fit into the keyhole slots

on the bottom of the base.

Follow the steps under “On a Wall Plate

or Wall” on Page 5, then apply these ad-

ditional instructions for placement on a

wall.

1. Drill two holes 315/16

inches (100 mm)

apart. Then thread

a screw into each

hole, letting the

heads extend about

5/16 inch (8 mm)

from the wall.

2. Plug one end of the supplied long

modular cord into the TEL LINE jack

on the back of the base.

3. Align the base’s keyhole slots with

the mounting screws and slide the

base down to secure it.

Handset

Holder

315/16

Inch

CONNECTING AND

CHARGING THEBATTERY

PACK

The phone comes with a rechargeable

nickel-cadmium battery pack in the

handset, but not connected. Before us-

ing your phone, you must connect the

battery pack and then charge it for about

24 hours.

1. Press down and slide the battery

compartment cover in the direction

of the arrow to remove it.

2. Lift the battery pack out of the com-

partment. Plug the battery pack’s

connector into the socket in the

compartment. The connector fits

only one way.

3. Put the battery pack in the compart-

ment.

4. Replace the cover.

To charge the battery pack, simply place

the handset on the base, either face up

or face down. The CHARGE/IN USE in-

dicator on the base lights.

Recharge the battery pack when the

handset beeps and the TALK/BATT indi-

cator flashes.

Important: Be sure the battery pack is

properly connected before you try to

charge it. The CHARGE/IN USE indica-

tor lights when the handset is on the

base, even if the battery pack is not con-

nected.

Notes:

• When you first use the phone after

charging or recharging the battery

pack, the phone might not work and

you might hear an error tone. If this

happens, return the handset to the

base for a few seconds.

• About once a month, fully discharge

the battery pack by keeping the

handset off the base until the TALK/

BATT indicator flashes. Otherwise,

the battery pack loses its ability to

fully recharge.

• Using a pencil eraser, clean the

charging contacts on the handset

and the base about once a month.

• If the TALK/BATT indicator does not

light and the phone does not work,

recharge the battery pack. (The bat-

tery power might be too low to light

the indicator.)

• If the battery pack becomes weak

during a call, you hear a beep and

the TALK/BATT indicator flashes

every 3 seconds. Recharge the bat-

tery pack.

• If the battery pack is completely dis-

charged, the handset loses the

security access-protection code. To

reset the code, place the handset on

the base and charge the battery

pack.

• The supplied battery pack should

last for about a year. When the bat-

tery pack loses its ability to fully

recharge, order a replacement bat-

tery pack from your local

RadioShack store (see “Replacing

the Battery Pack” on Page 18).

SETTING THE DIALING

MODE

Set DIAL MODE on the back of the base

for the type of service you have. If you

are not sure which type you have, once

the battery pack is fully charged, do this

test.

1. Be sure DIAL MODE is set to T

(tone).

2. Lift the handset, press TALK, and lis-

ten for a dial tone.

3. Press any number other than 0.

Note: If your phone system requires

that you dial an access code (9, for

example) before you dial an outside

number, do not press the access

code either.

If the dial tone stops, you have

touch-tone service. Leave DIAL

MODE

set to T.

If the dial tone continues, you have

pulse service. Set DIAL MODE to P

(pulse).

SETTING THE RINGER’S

TONE AND VOLUME

You can set two ringer tones and a high

and low volume for each.

To change the tone, lift the handset and

press VOL ▲or ▼. The selected tone

sounds at the selected volume for 2 sec-

onds.

Note: If the ringer does not change

when you press either VOL ▲or ▼, try

pressing the opposite button.

VOL ▲VOL ▼

OPERATION

MAKING AND RECEIVING

CALLS

To make a call, lift the handset and

press TALK. The TALK/BATT indicator

on the handset and the CHARGE/IN

USE indicator on the base light. When

you hear a dial tone, dial the number.

To answer a call, simply lift the handset.

If the handset is away from the base,

press any key.

To end a call, place the handset on the

base or press TALK.

Note: If you press TALK to hang up and

the phone does not disconnect, press

TALK again while holding the handset

closer to the base, or place the handset

on the base.

SELECTING THE

CHANNEL

The phone scans 10 channels and auto-

matically selects a clear channel each

time you make or receive a call.

If you hear other conversation or exces-

sive noise during a call, press CH to se-

lect a different channel. The TALK/BATT

indicator blinks, followed by a brief

pause as your phone searches for a

clear channel.

Note: If the handset is too far from the

base, the channel might not be clear.

Move closer to the base and try making

the call again.

SETTING THE HANDSET

VOLUME

You can choose one of four volume set-

tings (low, medium, high, or maximum)

for the handset. To change the volume,

press VOL ▲or ▼during a call.

Note: When you press VOL ▲while the

volume is maximum or VOL ▼while the

volume is low, the setting does not

change and the phone sounds an error

tone.

USING REDIAL

You can quickly dial the last number di-

aled. When you hear a dial tone, simply

press REDIAL.

TALK

REDIAL

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack ET-3504 Bedienungsanleitung

Radio Shack

Radio Shack 43-3880 Bedienungsanleitung

Radio Shack

Radio Shack TAD-733 Bedienungsanleitung

Radio Shack

Radio Shack 43-3815 Bedienungsanleitung

Radio Shack

Radio Shack ET-545 Bedienungsanleitung

Radio Shack

Radio Shack ET-550 Bedienungsanleitung

Radio Shack

Radio Shack 43-3576 Bedienungsanleitung

Radio Shack

Radio Shack 43-3575 Bedienungsanleitung

Radio Shack

Radio Shack 43-3585 Bedienungsanleitung

Radio Shack

Radio Shack 43-3570 Bedienungsanleitung

Radio Shack

Radio Shack 43-325 Bedienungsanleitung

Radio Shack

Radio Shack ET-1118 Bedienungsanleitung

Radio Shack

Radio Shack 43-683 Bedienungsanleitung

Radio Shack

Radio Shack 43-3857 Bedienungsanleitung

Radio Shack

Radio Shack 4301122D Bedienungsanleitung

Radio Shack

Radio Shack 43-3887 Bedienungsanleitung

Radio Shack

Radio Shack 43-141 Bedienungsanleitung

Radio Shack

Radio Shack Digital Answering System with Caller ID Deluxe and 2.4 GHz Digital Spread Spectrum Cordless... Bedienungsanleitung

Radio Shack

Radio Shack 43-143 Bedienungsanleitung

Radio Shack

Radio Shack ET-916 Bedienungsanleitung

Radio Shack

Radio Shack ET-536 Bedienungsanleitung

Radio Shack

Radio Shack 43-3526 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Dual Keypad Cordless Telephone with Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack ET-1123 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung