Radio Shack TAD-733 Bedienungsanleitung

Cat. No. 43-733

OWNER’S MANUAL

Please read before using this equipment.

TAD-733

900 MHz Digital Spread Spectrum

Cordless Telephone and

Answering System

with Headset Jack

43-733.fm Page 1 Friday, September 17, 1999 8:57 AM

RadioShack is a registered trademark used by Tandy Corporation.

FEATURES

Your RadioShack TAD-733 900 MHz

Digital Spread Spectrum Cordless Tele-

phone and Answering System uses ad-

vanced cordless telephone technology

to give you superior audio quality. Its

cordless operation lets you move freely

around your home or office.

The TAD-733 stores 12-minutes of mes-

sages on a computer chip. This gives

you better performance than tape-based

answering machines. For example, you

can delete an individual message while

saving the rest. Because your TAD is

fully digital, there are no tapes to bother

with and no tape mechanisms to wear

out.

You can operate the TAD-733 remotely

from a touch-tone phone, even if it is not

turned on.

TAD FEATURES

Date/Time Stamp — records the day

and time each message was recorded.

Two User Mailboxes and a Message

Center — stores messages, each up to

60 seconds long (for a total of up to 12

minutes or 62 messages) in one of the

user mailboxes or in the general mes-

sage center.

Pre-Recorded Message — gives you

the option of using the TAD-733’s exist-

ing outgoing message or recording your

own (up to 60 seconds long).

Announce-Only — lets you play an an-

nouncement for callers to hear, without

recording their messages.

Remote Operation — lets you use a

touch-tone phone (or rotary phone and

pocket tone dialer) to operate the TAD

while you are away from your home or

office.

Remote Answer-On — lets you turn on

the TAD from a remote location even

when it is not set to answer calls.

Programmable Remote Operation Se-

curity Code — you can set a two-digit

security code for remote operation.

Call Screening — lets you listen as a

caller leaves a message so you can de-

cide whether or not to answer the call.

Memo Recording — lets you leave

messages for yourself or others in your

home or office.

Adjustable Ring Number — lets you

set the TAD to answer after four or sev-

en rings.

Toll-Saver — lets you avoid unneces-

sary long-distance charges when you

call by long distance to check your mes-

sages.

Phone Pick-Up Detection — stops re-

cording when you pick up any phone on

the same line as the TAD.

43-733.fm Page 2 Friday, September 17, 1999 8:57 AM

TELEPHONE FEATURES

900 MHz Operation — provides better

sound and less interference than many

other cordless phones.

Digital Spread Spectrum — provides

the longest range and the utmost in se-

curity. Frequencies are constantly

changing across the entire 900 MHz

band, making it difficult for anyone to

monitor your calls on scanners.

20 Channels — scans the frequency

pairs used between the base and the

handset and automatically selects a

clear channel each time you make or re-

ceive a call.

20-Number Memory Dialing — lets

you store up to 20 phone numbers in

memory for easy dialing.

Any-Key Answer — lets you press any

key on the handset to answer an incom-

ing call.

Security Access-Protection Code —

helps prevent other cordless phones

from using your phone line while the

handset is off the base.

Page —lets you send a paging signal

from the base to the handset to page

someone or locate the handset when it

is away from the base.

Headset Jack — lets you connect an

optional headset (available at your local

RadioShack store) for hands-free con-

venience.

Hearing Aid Compatible — lets you

use this telephone with hearing aids that

have a T (telephone) switch.

This telephone device has been tested

and found to comply with all applicable

UL and FCC standards.

WARNING: To reduce the risk of fire or

shock hazard, do not expose this product to rain

or moisture.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT OPEN.

CAUTION: TO REDUCE THE RISK OF

ELECTRIC SHOCK, DO NOT REMOVE

COVER OR BACK. NO USER-SERVICE-

ABLE PARTS INSIDE. REFER SERVICING

TO QUALIFIED PERSONNEL.

This symbol is intended to alert

you to the presence of uninsu-

lated dangerous voltage within

the product’s enclosure that might

be of sufficient magnitude to con-

stitute a risk of electric shock. Do

not open the product’s case.

This symbol is intended to inform

you that important operating and

maintenance instructions are

included in the literature accom-

panying this product.

43-733.fm Page 3 Friday, September 17, 1999 8:57 AM

Important: Cordless phones such as

this one require AC power to operate.

When AC power is off, you cannot dial

out or receive incoming calls using your

TAD-733. For this reason, the TAD-733

should not be your only telephone. To

be safe, you should also have a phone

that does not require AC power to oper-

ate (not a cordless phone) so you can

still make and receive calls if there is an

AC power failure.

READ THIS BEFORE

INSTALLATION

Your TAD-733 conforms to federal regu-

lations, and you can connect it to most

telephone lines. However, each device

you connect to the telephone line draws

power from the telephone line. We refer

to this power draw as the device’s

ringer

equivalence number

, or REN. The REN

is on the label on the back of the base.

If you are using more than one phone or

other device on the line, add up all the

RENs. If the total is more than five (three

in rural areas), your phone might not

ring and your answering system might

not answer. If ringer operation is im-

paired, remove a device from the line.

FCC STATEMENT

Your TAD-733 complies with Part 68 of

FCC Rules

. You must, upon request,

provide the FCC Registration Number

and the REN to your phone company.

These numbers are on the label on the

back of the base.

You must not connect your phone to any

of the following:

• coin-operated systems

• party-line systems

• most electronic key phone systems

Note: Your telephone operates on stan-

dard radio frequencies, as allocated by

the FCC. Even though the security

access-protection code prevents unau-

thorized use of your phone line, it is pos-

sible for other radio units operating on

similar frequencies within a certain area

to unintentionally intercept your conver-

sations and/or cause interference. This

lack of privacy can occur with any cord-

less phone.

43-733.fm Page 4 Friday, September 17, 1999 8:57 AM

CONTENTS

Preparation .............................................................................................................. 7

Selecting a Location ........................................................................................... 7

Installing the Handset’s Antenna ........................................................................ 7

Installing the Phone ............................................................................................ 7

On a Desk Top ............................................................................................. 7

On a Wall Plate ............................................................................................ 8

Connecting and Charging the Handset Battery Pack ......................................... 9

Setting the Dialing Mode and Ringers .............................................................. 11

Dialing Mode .............................................................................................. 11

Ringers ...................................................................................................... 11

Number of Rings ........................................................................................ 12

Setting The Ringer’s Volume ..................................................................... 12

Checking/Setting the Ringer Tone ............................................................. 12

Setting the Day and Time ................................................................................. 12

With the Handset ....................................................................................... 12

With the Base ............................................................................................ 13

Telephone Operation ............................................................................................ 14

Making and Receiving a Call ............................................................................ 14

Setting the Handset’s Volume .......................................................................... 14

Using Redial ..................................................................................................... 14

Using Flash ...................................................................................................... 15

Using Mute ....................................................................................................... 15

Using Tone Services on a Pulse Line ............................................................... 15

Using Page ....................................................................................................... 16

Memory Dialing ................................................................................................ 16

Storing a Number in Memory ..................................................................... 16

Entering a Pause ....................................................................................... 17

Dialing a Stored Number ........................................................................... 17

Chain-Dialing Service Numbers ................................................................. 17

Testing Stored Emergency Numbers ......................................................... 17

Using an Optional Headset .............................................................................. 17

Removing the Belt Clip ..................................................................................... 18

TAD Operation ....................................................................................................... 19

Setting the TAD to Answer Calls ...................................................................... 19

Using the Mailboxes ......................................................................................... 19

Recording an Outgoing Message ..................................................................... 19

Deleting an Outgoing Message ........................................................................ 20

Screening Calls ................................................................................................ 20

Adjusting the TAD’s Volume ............................................................................. 21

Recording Incoming Messages ........................................................................ 21

43-733.fm Page 5 Friday, September 17, 1999 8:57 AM

Recording a Memo ........................................................................................... 21

Playing Messages ............................................................................................ 22

Deleting Messages ........................................................................................... 22

Changing the Remote Operation Security Code .............................................. 23

Remote Operation ................................................................................................. 24

Using Toll-Saver ............................................................................................... 24

Using Remote

Answer-On .............................................................................................................. 24

Using Remote Commands ............................................................................... 24

Remote Commands ................................................................................... 25

Troubleshooting .................................................................................................... 26

Care and Maintenance .......................................................................................... 27

Replacing the Battery Pack .............................................................................. 28

The FCC Wants You to Know ........................................................................... 29

Lightning ........................................................................................................... 29

43-733.fm Page 6 Friday, September 17, 1999 8:57 AM

PREPARATION

SELECTING A LOCATION

You can place the phone on a desk top

or table, or mount it on a standard wall

plate. Select a location that is:

• near an accessible AC outlet

• near a telephone line jack

• out of the way of normal activities

• away from electrical machinery,

electrical appliances, metal walls or

filing cabinets, wireless intercoms,

alarms, and room monitors

The base’s location affects the phone’s

range. If you have a choice of several lo-

cations, try each to see which provides

the best performance.

Cautions:

You must use a Class 2

power source that supplies

9V DC and delivers at least

800 mA. Its center tip must be set to

positive and its plug must fit the

TAD-733's

DC 9V jack. The supplied

adapter meets these specifications.

Using an adapter that does not meet

these specifications could damage

the TAD-733 or the adapter.

• Always connect the AC adapter to

the TAD-733 before you connect it

to AC power. When you finish, dis-

connect the adapter from AC power

before you disconnect it from the

TAD-733.

INSTALLING

THE

HANDSET’S

ANTENNA

Screw the antenna into

the hole at the top of the

handset.

INSTALLING THE PHONE

On a Desk Top

1. Remove the mounting bracket by

holding in both tabs and gently pull-

ing out the wide end of the bracket.

2. Plug one end of the supplied long

modular cord into the telephone jack

on the back of the base.

3. Plug the modular cord’s other end

into a modular phone line jack.

43-733.fm Page 7 Friday, September 17, 1999 8:57 AM

4. Insert the supplied AC adapter’s

barrel plug into the DC 9V jack on

the back of the base.

5. Route the adapter’s cord through

the strain relief slot on the back of

the base.

6. Insert the tabs on the narrow end of

the bracket into the inner pair of

slots near the bottom of the base

and snap the tabs at the wide end of

the bracket into place.

Strain

Relief

Slot

7. Plug the adapter into a standard AC

outlet. The TAD-733 beeps and 00

appears.

8. Raise the base’s antenna to a verti-

cal position.

On a Wall Plate

1. Follow Steps 1–4 under “On a Desk

Top” on Page 7.

2. Route the modular cord through the

left groove on the bottom of the

base and the adapter cord through

the groove below the strain relief

slot.

3. Route the end of the modular cord

through the hole in the bracket, and

insert the tabs on the narrow end of

the bracket into the inner pair of

slots near the top of the base.

Strain

Relief

Slot

43-733.fm Page 8 Friday, September 17, 1999 8:57 AM

4. Snap the tabs at the wide end of the

bracket into place.

5. Plug the modular cord into the wall

plate jack. Align the base’s keyhole

slots with the wall plate studs and

slide the base downward to secure

it.

6. Plug the AC adapter into a standard

AC outlet. The TAD-733 beeps and

00 appears.

7. Raise the base’s antenna to a verti-

cal position.

CONNECTING AND

CHARGING THE

HANDSET BATTERY

PACK

The TAD-733 comes with a recharge-

able nickel-cadmium battery pack in the

handset but not connected. Before using

your phone, you must connect the bat-

tery pack and then charge it for about 15

hours.

1. Press down and slide off the battery

compartment cover.

2. Lift the battery pack out of the com-

partment, and plug its connector into

the socket inside the compartment.

The connector fits only one way.

3. Put the battery pack in the compart-

ment and replace the cover.

43-733.fm Page 9 Friday, September 17, 1999 8:57 AM

4. To charge the battery pack, place

the handset on the base. The IN

USE indicator flashes for 1 second

and the CHARGE indicator auto-

matically lights after 4 seconds.

Recharge the battery pack when the

LOW BATT indicator on the handset

flashes.

Notes:

• You can place the handset on the

base facedown or faceup without re-

moving the belt clip. If you want to

use the hanging hole on the back of

the handset to place the handset on

the wall-mounted base faceup, re-

move the belt clip (see “Removing

the Belt Clip” on Page 18).

• If the CHARGE indicator does not

light when you place the handset on

the base, be sure the battery pack

and AC adapter are correctly and

securely connected.

Also, check the charging contacts

on the handset and base. If the con-

tacts are dirty or tarnished, clean

them with a pencil eraser.

• When you first use the phone after

charging or recharging the battery

pack, the phone might not work and

you might hear 3 short beeps when

you press TALK. If this happens, re-

turn the handset to the base for about

5 seconds. This resets the security

access-protection code.

• About once a month, fully discharge

the battery pack by keeping the hand-

set off the base until the LOW BATT

indicator lights. Otherwise, the bat-

tery pack loses its ability to fully re-

charge.

• If the LOW BATT indicator does not

light, but the phone does not work, re-

charge the battery pack. (The battery

pack charge might be too low to light

the indicator.)

• If the battery pack becomes weak

during a call, you hear 3 beeps and

the LOW BATT indicator flashes. End

the call as soon as conveniently pos-

sible, and recharge the battery pack

before using the phone again.

CHARGE

Indicator

IN USE

Indicator

LOW BATT

Indicator

43-733.fm Page 10 Friday, September 17, 1999 8:57 AM

Inhaltsverzeichnis

Andere Radio Shack Schnurloses Telefon Handbücher

Radio Shack

Radio Shack 43-3814 Bedienungsanleitung

Radio Shack

Radio Shack ET-1119 Bedienungsanleitung

Radio Shack

Radio Shack Cordless Phone Bedienungsanleitung

Radio Shack

Radio Shack TAD-734 Bedienungsanleitung

Radio Shack

Radio Shack ET-553 Bedienungsanleitung

Radio Shack

Radio Shack ET-1112 Bedienungsanleitung

Radio Shack

Radio Shack ET-518 Bedienungsanleitung

Radio Shack

Radio Shack ET-598 Bedienungsanleitung

Radio Shack

Radio Shack ET-1124 Bedienungsanleitung

Radio Shack

Radio Shack 43-3571 Bedienungsanleitung

Radio Shack

Radio Shack 43-141 Bedienungsanleitung

Radio Shack

Radio Shack ET-1111 Bedienungsanleitung

Radio Shack

Radio Shack TAD-1010 Bedienungsanleitung

Radio Shack

Radio Shack 900 MHz Digital Spread Spectrum Cordless Phone with Digital Answerer and Caller ID/Call Waiting... Bedienungsanleitung

Radio Shack

Radio Shack ET-910 Bedienungsanleitung

Radio Shack

Radio Shack 43-3856 Bedienungsanleitung

Radio Shack

Radio Shack 43-3821 Bedienungsanleitung

Radio Shack

Radio Shack ET-927 Bedienungsanleitung

Radio Shack

Radio Shack ET-1118 Bedienungsanleitung

Radio Shack

Radio Shack ET-539 Bedienungsanleitung

Radio Shack

Radio Shack ET-685 Bedienungsanleitung

Radio Shack

Radio Shack 43-3704 Bedienungsanleitung

Radio Shack

Radio Shack ET-689 Bedienungsanleitung

Radio Shack

Radio Shack 43-143 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch

AT&T

AT&T 7625 Bedienungsanleitung