ResMed AirSense 10 Bedienungsanleitung

User guide

English

User guide

www.TheCPAPShop.com

866-414-9700

English 1

ENGLISH

Welcome

The AirSense™10 AutoSet™and AirSense 10 AutoSet for Her are ResMed's premium auto-adjusting

pressure devices. The AirSense 10 Elite and AirSense 10 CPAP are ResMed's Continuous Positive

Airway Pressure (CPAP) devices.

WARNING

Read this entire guide before using the device.

CAUTION

In the US, Federal law restricts this device to sale by or on the order of a physician.

Indications for use

AirSense 10 AutoSet

The AirSense 10 AutoSet self-adjusting device is indicated for the treatment of obstructive sleep

apnea (OSA) in patients weighing more than 66 lb (30 kg). It is intended for home and hospital use.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

AirSense 10 AutoSet for Her

The AirSense 10 AutoSet for Her self-adjusting device is indicated for the treatment of obstructive

sleep apnea (OSA) in patients (female patients with mild to moderate OSA when using AutoSet for

Her treatment mode) weighing more than 66 lb (30 kg). It is intended for home and hospital use.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

AirSense 10 Elite

The AirSense 10 Elite device is indicated for the treatment of obstructive sleep apnea (OSA) in

patients weighing more than 66 lb (30 kg). It is intended for home and hospital use.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

AirSense 10 CPAP

The AirSense 10 CPAP device is indicated for the treatment of obstructive sleep apnea (OSA) in

patients weighing more than 66 lb (30 kg). It is intended for home and hospital use.

The humidifier is intended for single patient use in the home environment and re-use in a

hospital/institutional environment.

Contraindications

Positive airway pressure therapy may be contraindicated in some patients with the following pre-

existing conditions:

severe bullous lung disease

pneumothorax

pathologically low blood pressure

dehydration

cerebrospinal fluid leak, recent cranial surgery, or trauma.

Adverse effects

You should report unusual chest pain, severe headache, or increased breathlessness to your

prescribing physician. An acute upper respiratory tract infection may require temporary

discontinuation of treatment.

The following side effects may arise during the course of therapy with the device:

drying of the nose, mouth, or throat

nosebleed

bloating

ear or sinus discomfort

eye irritation

skin rashes.

At a glance

The AirSense 10 includes the following:

Device with HumidAir integrated humidifier

Water tub

Air tubing

Power supply unit

Travel bag

SD card (already inserted).

Contact your care provider for a range of accessories available for use with the device including:

Air tubing (heated and non-heated): ClimateLineAir™, SlimLine™, Standard

Water tub: Standard water tub, cleanable water tub (can be disinfected)

Filter: Hypoallergenic filter, standard filter

Air10™DC/DC converter

SD card reader

Air10 oximeter adapter

Air10 USB adapter.

English 3

About your device

1 Air outlet 5 Water tub

2 Air filter cover 6 Screen

3 Power inlet 7 Adapter cover

4 Serial number and device number 8 SD card cover

About the control panel

Start/Stop button

Press to start/stop therapy.

Press and hold for three seconds to enter power save

mode.

Dial

Turn to navigate the menu and press to select an option.

Turn to adjust a selected option and press to save your

change.

Home button Press to return to the Home screen.

Different icons may be displayed on the screen at different times including:

Ramp Time

Wireless signal strength (green)

Ramp Time Auto

Wireless transfer not enabled (gray)

Humidity No wireless connection

Humidifier warming

Airplane Mode

Humidifier cooling

Setup

CAUTION

Do not overfill the water tub as water may enter the device and air tubing.

1. Place the device on a stable level surface.

2. Plug the power connector into the rear of the device. Connect one end of the power cord into

the power supply unit and the other end into the power outlet.

3. Connect the air tubing firmly to the air outlet located on the rear of the device.

4. Open the water tub and fill it with distilled water up to the maximum water level mark.

Do not fill the water tub with hot water.

5. Close the water tub and insert it into the side of the device.

6. Connect the free end of the air tubing firmly onto the assembled mask.

See the mask user guide for detailed information.

Recommended masks are available on www.resmed.com.

English 5

Starting therapy

1. Fit your mask.

2. Press Start/Stop or breathe normally if SmartStart is enabled.

You will know that therapy is on when the Sleep Report screen is displayed.

The current treatment pressure is shown in green.

During ramp time the pressure is gradually increasing and you will see a

spinning circle. Once the prescribed treatment pressure is reached, the entire

circle will be green.

The screen will go black automatically after a short period of time. You can press Home or the dial to

turn it back on. If power is interrupted during therapy, the device will automatically restart therapy

when power is restored.

The AirSense 10 device has a light sensor that adjusts the screen brightness based on the light in

the room.

Stopping therapy

1. Remove your mask.

2. Press Start/Stop or if SmartStart is enabled, therapy will stop automatically after a few seconds.

The Sleep Report now gives you a summary of your therapy session.

Usage hours

–

Indicates the number of hours of therapy you received last

session.

Mask Seal–Indicates how well your mask sealed:

Good mask seal.

Needs adjusting, see Mask Fit.

Humidifier–Indicates if your humidifier is working properly:

Humidifier working.

Humidifier might be faulty, contact your care provider.

If set by your care provider, you will also see:

Events (AHI) per hour–Indicates the number of apneas and hypopneas experienced per hour.

More Info–Turn the dial to scroll down to view more detailed usage data.

Power save mode

Your AirSense 10 device records your therapy data. In order to allow it to transmit the data to your

care provider, you should not unplug the device. However, you can put it into power save mode to

save electricity.

To enter power save mode:

Press and hold Start/Stop for three seconds.

The screen goes black.

To exit power save mode:

Press Start/Stop once.

The Home screen is displayed.

My Options

Your AirSense 10 device has been set up for your needs by your care provider, but you may find you

want to make small adjustments to make your therapy more comfortable.

Highlight My Options and press the dial to see your

current settings. From here, you can personalize your

options.

Ramp Time

Designed to make the beginning of therapy more comfortable, Ramp Time is the period during

which the pressure increases from a low start pressure to the prescribed treatment pressure.

You can set your Ramp Time to Off, 5 to 45 minutes or Auto. When Ramp Time is set to Auto, the

device will detect when you have fallen asleep and then automatically rise to the prescribed

treatment pressure.

To adjust Ramp Time:

1. In My Options, turn the dial to highlight Ramp

Time and then press the dial.

2. Turn the dial to adjust the ramp time to your

preferred setting and press the dial to save the

change.

Humidity Level

The humidifier moistens the air and is designed to make therapy more comfortable. If you are

getting a dry nose or mouth, turn up the humidity. If you are getting any moisture in your mask, turn

down the humidity.

You can set the Humidity Level to Off or between 1 and 8, where 1 is the lowest humidity setting

and 8 is the highest humidity setting.

English 7

To adjust the Humidity Level:

1. In My Options, turn the dial to highlight Humidity

Level and then press the dial.

2. Turn the dial to adjust the humidity level and press

the dial to save the change.

If you continue to get a dry nose or mouth, or moisture in your mask, consider using ClimateLineAir

heated air tubing. ClimateLineAir together with Climate Control delivers more comfortable therapy.

Mask Fit

Mask Fit is designed to help you assess and identify possible air leaks around your mask.

To check Mask Fit:

1. Fit the mask as described in the mask user guide.

2. In My Options, turn the dial to highlight Run Mask Fit and then press the

dial.

The device starts blowing air.

3. Adjust the mask, mask cushion and headgear until you get a Good result.

To stop Mask Fit, press the dial or Start/Stop. If you are unable to get a good mask seal, talk to your

care provider.

More options

Your care provider may have given you access to personalize a few more options.

Pressure Relief When Pressure Relief is enabled, you may find it easier to breathe out. This

can help you get used to therapy.

SmartStart When SmartStart is enabled, therapy starts automatically when you breathe

into your mask. When you remove your mask, it stops automatically after few

seconds.

Mask This option shows your mask type setting. If you use more than one type of

mask, adjust this setting when switching between masks.

Run Warmup This option allows you to pre-heat the water before starting therapy, so that

the air is not cold or dry at the beginning of therapy.

Caring for your device

It is important that you regularly clean your AirSense 10 device to make sure you receive optimal

therapy. The following sections will help you with disassembling, cleaning, checking and

reassembling your device.

Disassembling

1. Hold the water tub at the top and bottom, press it gently and pull it away from the device.

2. Open the water tub and discard any remaining water.

3. Hold the cuff of the air tubing and gently pull it away from the device.

4. Hold both the cuff of the air tubing and the swivel of the mask, then gently pull apart.

Cleaning

You should clean the device weekly as described. Refer to the mask user guide for detailed

instructions on cleaning your mask.

1. Wash the water tub and air tubing in warm water using mild detergent.

Do not wash in a dishwasher or washing machine.

2. Rinse the water tub and air tubing thoroughly and allow to dry out of direct sunlight and/or heat.

3. Wipe the exterior of the device with a dry cloth.

Checking

You should regularly check the water tub, air tubing and the air filter for any damage.

1. Check the water tub:

Replace it if it is leaking or has become cracked, cloudy or pitted.

Replace it if the seal is cracked or torn.

Remove any white powder deposits using a solution of one part household vinegar to

10 parts water.

2. Check the air tubing and replace it if there are any holes, tears or cracks.

3. Check the air filter and replace it at least every six months. Replace it more often if there are any

holes or blockages by dirt or dust.

English 9

To replace the air filter:

1. Open the air filter cover and remove the old air filter.

The air filter is not washable or reusable.

2. Place a new air filter onto the air filter cover and then close it.

Make sure the air filter is fitted at all times to prevent water and dust from entering the device.

Reassembling

When the water tub and air tubing are dry, you can reassemble the parts.

1. Connect the air tubing firmly to the air outlet located on the rear of the device.

2. Open the water tub and fill it with distilled room temperature water up to the maximum water

level mark.

3. Close the water tub and insert it into the side of the device.

4. Connect the free end of the air tubing firmly onto the assembled mask.

Therapy data

Your AirSense 10 device records your therapy data for you and your care provider so they can view

and make changes to your therapy if required. The data is recorded and then transferred to your care

provider wirelessly or via an SD card.

Wireless

Your AirSense 10 device is equipped with cellular communication. This allows your therapy data to

be wirelessly transmitted to your care provider to enhance the quality of your treatment. The

Wireless signal strength icon displayed at the top right of your screen indicates the signal

strength.

The data is usually transmitted after therapy has stopped. In order to make sure that your data is

transferred, leave your device connected to the mains power at all times and make sure that it is not

in Airplane Mode.

Notes:

Therapy data might not be transmitted if you use it outside of the country or region of purchase.

Devices with cellular communication might not be available in all regions.

SD card

An alternative way for your therapy data to be transferred to your care provider is via the SD card.

Your care provider may ask you to send the SD card by mail or to bring it in. When instructed by

your care provider, remove the SD card.

Do not remove the SD card from the device when the SD light is flashing.

Andere Handbücher für AirSense 10

Inhaltsverzeichnis

Andere ResMed Medizinische Geräte Handbücher

ResMed

ResMed ApneaLink Bedienungsanleitung

ResMed

ResMed Flow Generator AutoSet CS 2 Bedienungsanleitung

ResMed

ResMed AirFit N30i Bedienungsanleitung

ResMed

ResMed Astral 100 Series Bedienungsanleitung

ResMed

ResMed Astral Series Bedienungsanleitung

ResMed

ResMed Mirage FX Bedienungsanleitung

ResMed

ResMed Lumis 100 VPAP S Bedienungsanleitung

ResMed

ResMed AirFit N30 Bedienungsanleitung

ResMed

ResMed AIRMINI Bedienungsanleitung

ResMed

ResMed S9 Series Bedienungsanleitung

ResMed

ResMed S8 ESCAPE System Bedienungsanleitung

ResMed

ResMed AcuCare F1-0 Bedienungsanleitung

ResMed

ResMed airsense 10 autoset Montageanleitung

ResMed

ResMed Astral 150 Bedienungsanleitung

ResMed

ResMed ELITE S8 Bedienungsanleitung

ResMed

ResMed AirSense 11 Bedienungsanleitung

ResMed

ResMed Mirage Swift II Bedienungsanleitung

ResMed

ResMed Ultra Mirage Bedienungsanleitung

ResMed

ResMed ApneaLink Bedienungsanleitung

ResMed

ResMed S8 ESCAPE System Bedienungsanleitung

ResMed

ResMed AirFit F20 Bedienungsanleitung

ResMed

ResMed Swift FX Nano Montageanleitung

ResMed

ResMed VS III Bedienungsanleitung

ResMed

ResMed Quattro FX Bedienungsanleitung

Beliebte Medizinische Geräte Handbücher anderer Marken

TekTone

TekTone Tek-CARE160 Bedienungsanleitung

NeuroMetrix

NeuroMetrix Quell 2.0 Bedienungsanleitung

AMT

AMT XLR8 Bedienungsanleitung

EDAN

EDAN SONOTRAX Pro Bedienungsanleitung

Restorative Therapies

Restorative Therapies RT300 Bedienungsanleitung

Gendex

Gendex Expert DC Bedienungsanleitung

Dexcowin

Dexcowin ADX4000W Bedienungsanleitung

Libelium

Libelium MySignals Bedienungsanleitung

Acelity

Acelity V.A.C.ULTA 4 Bedienungsanleitung

Caputron

Caputron ActivaDose II tDCS Bedienungsanleitung

Plinth 2000

Plinth 2000 93CDT Bedienungsanleitung

GE SENOGRAPHE 800T Bedienungsanleitung

GE Definium 5000 Bedienungsanleitung

Kanmed

Kanmed GE-1380 Bedienungsanleitung

Huntleigh

Huntleigh FD1 Bedienungsanleitung

Stryker

Stryker SPR Plus Bedienungsanleitung

Tobii Dynavox

Tobii Dynavox I-Series Bedienungsanleitung

S-Capepod

S-Capepod Evac Cocoon Bedienungsanleitung