ResMed Nasal Pillows System Swift LT Bedienungsanleitung

Swift™ LT

nasal PIllOWs sYsTEM

User Guide

English

Swift™ LT

nasal PIllOWs sYsTEM

Thank you for choosing the Swift LT.

Intended Use

The Swift LT channels airﬂow noninvasively to a patient from a positive airway

pressure device such as a continuous positive airway pressure (CPAP) or

bilevel system.

The Swift LT is:

to be used by adult patients (> 66 lb/30 kg) for whom positive airway•

pressure has been prescribed

intended for single-patient re-use in the home environment and•

multipatient re-use in the hospital/institutional environment.

Using the Swift LT

When using the Swift LT with ResMed ﬂow generators that have mask setting

options, if available select ‘SWIFT’; otherwise select ‘MIRAGE’ as the mask

option.

Notes:

The Swift LT is not compatible for use with ResMed AutoSet CS™ 2 and•

VPAP™ Adapt SV devices.

SmartStop may not operate effectively when using Swift LT with some•

ﬂow generators that have this feature.

If you experience nasal dryness or irritation, use of a humidiﬁer is•

recommended.

Rx Only

Parts of the Swift LT & Ordering Information

Complete system

60560

(includes small, medium and large pillows)

Frame system

(pillows, frame, short tube assembly)

S* 60582; M* 60583; L* 60584.

Frame assembly

(frame, short tube assembly)

60581

S* Small; M* Medium; L* Large.

Elbow

Short tube assembly

60577

Frame

60575

Swivel

Pillows

60571 (S*)

60572 (M*)

60573 (L*)

Plastic tube retainer

60586

Top buckle

60579 (1)

60580 (10)

Headgear

assembly

60578

Back buckle

60558 (1)

60559 (10)

Velcro™ tube retainer

(sold separately)

60557

English

Fitting your Swift LT

123

(A) Hold the pillows at

your nose; (B) pull the

headgear over your head.

Adjust top straps (over-

tightening may cause

excess pressure on your

nose).

Adjust each end of the

backstrap (overtightening

may cause excess

pressure on upper lip).

456

Rotate frame to adjust

pillow angle to ensure it

sits comfortably.

Connect the short tube

to the ﬂow generator’s air

tubing.

The Swift LT is now ﬁtted

and ready for use. Head-

gear should sit midway

between ear and eye.

Using the PlasticTube Retainer (Optional)

Swift LT

Push tube retainer into

buckle. Clip either short

tube or air tubing to tube

retainer.

When using the tube

retainer, the tubing can be

positioned to either side of

your face or centered.

If the mask pulls on your

nose, increase length of

tube between mask and

tube retainer.

Back buckle

60558 (1)

60559 (10)

Disassembling your Swift LT

Swift LT

Detach air tubing from

short tube. Remove headgear from

frame.

Remove pillows from

frame. Remove elbow from frame.

Cleaning your Swift LT in the home

Notes:

The nasal pillows system and headgear should be cleaned by•

handwashing.

The headgear may be washed without being disassembled.•

WARNING

Do not use aromatic-based solutions or scented oils (eg, eucalyptus or

essential oils), bleach, alcohol or products that smell strongly (eg, citrus)

to clean any of the system’s components. Residual vapours from these

solutions can be inhaled if not rinsed thoroughly. They may also damage

the system, causing cracks.

English

CAUTION

If any visible deterioration of a system component is apparent (cracking,

crazing, tears etc.), the component should be discarded and replaced.

Daily/After Each Use

Handwash the separated mask components (excluding headgear) by gently

rubbing in warm (approx. 86°F/30°C) water using mild soap for one minute.

Rinse all components well with drinking quality water and allow them to air

dry out of direct sunlight.

Weekly

Handwash the headgear and tube retainer in warm (approx. 86°F/30°C)

water using mild soap. Rinse well and allow them to air dry out of direct

sunlight.

Reprocessing your Swift LT between Patients

The Nasal Pillows System should be reprocessed when used between

patients. Cleaning, disinfection and sterilization instructions are available from

the ResMed website, www.resmed.com/masks/sterilization/americas.

If you do not have Internet access, please contact your ResMed

representative.

Storage

Ensure that your Swift LT is thoroughly clean and dry before storing it for any

length of time. Store the mask in a cool dry place out of direct sunlight.

Disposal

The Swift LT does not contain any hazardous substances and may be disposed

of with your normal household refuse.

Limited Warranty

ResMed warrants that your ResMed system, including its components: frame,

pillow sleeve, headgear, tubing and other accessories (“Product”) shall be free

from defects in material and workmanship for a period of ninety (90) days from

the date of purchase by the initial consumer.

For further details refer to the Warranty.

Reassembling your Swift LT

Insert elbow into frame. Align pillows with frame. Push pillows ﬁrmly into

frame. Ensure top and

bottom retention tabs slot

into place.

Check positioning markers

on pillows and headgear

are on the same side.

Slide left and right headgear stability arms onto frame.

Ensure inner wall of pillows is in correct position.

If not, squeeze pillow sides to release inner walls.

Reassembling the headgear

Swift LT

Lay out the headgear as

shown, writing facing

upwards.

(A) Thread the top straps

through the top buckle,

then (B) back over to

secure.

(A) Thread both backstraps

through the back buckle

(Velcro™ facing outwards),

then (B) fold back over to

secure.

English

Troubleshooting

Possible reason Solution

Pillows won’t seal properly, are uncomfortable or cause red marks

Pillows may have

been ﬁtted incorrectly,

incorrectly adjusted, or

the headgear is too tight.

Carefully follow instructions in “Fitting your Swift LT”.

Check headgear is not over-tightened.

Check ResMed logo on top of pillows is facing

outwards.

Inner wall position of one/

both pillows is incorrect. Squeeze pillow sides to release inner wall.The

correct position in shown in “Reassembling your

Swift LT”.

Pillows are wrong size. Talk to your clinician.

Pillows may be dirty. Clean pillows according to instructions in “Cleaning

your Swift LT in the Home”.

Nasal pillows system is too noisy

System is assembled

incorrectly. Reassemble the Swift LT. Make sure the pillows are

fully inserted into the frame.

Before using your Swift LT

WARNINGS

The vent holes must be kept clear.•

The mask should not be used unless the CPAP system is turned on and•

operating properly.

Follow all precautions when using supplemental oxygen.•

Oxygen ﬂow must be turned off when the ﬂow generator is not operating,•

so that unused oxygen does not accumulate within the ﬂow generator

enclosure and create a risk of ﬁre.

At a ﬁxed ﬂow rate of supplemental oxygen ﬂow, the inhaled oxygen•

concentration varies, depending on the pressure settings, patient breathing

pattern, mask, point of application and leak rate.

The technical speciﬁcations of the mask are provided for your clinician to•

check that they are compatible with the ﬂow generator. If used outside

speciﬁcation or if used with incompatible devices, the seal and comfort of

the mask may not be effective, optimum therapy may not be achieved, and

leak, or variation in the rate of leak, may affect the ﬂow generator function.

Discontinue using the Swift LT if you have ANY adverse reaction to the use•

of the mask, and consult your physician or sleep therapist.

As with all masks, some rebreathing may occur at low CPAP pressures.•

Refer to your ﬂow generator manual for details on settings and operational•

information.

Remove all packaging before using the mask.•

Technical speciﬁcations

Note: The mask system does not contain latex, PVC or DEHP materials.

Pressure–Flow

Curve Note: The mask contains passive venting that meets the

requirements for protection against rebreathing as speciﬁed in

ISO 17510-2. As a result of manufacturing variations, the vent

ﬂow rate may vary.

Pressure

(cm H2O)

Flow

(L/min)

4 21

8 28

12 33

16 38

20 42

Vent Flow Rate (L/min)

Mask Pressure (cm H2O)

Dead Space

Information Physical dead space is the empty volume of the mask to the

end of the swivel. Using the large cushions this is 94 mL.

Standards CE designation in accordance with EC directive 93/42/EEC,

class IIa. ISO 14971, ISO 13485, ISO 10993-1 and ISO 17510-2.

Therapy

Pressure 4 to 20 cm H2O.

Resistance Drop in pressure measured (nominal)

at 50 L/min: 0.54 cm H2O and at 100 L/min: 1.95 cm H2O.

Sound DECLARED DUAL-NUMBER NOISE EMISSION VALUES in

accordance with ISO 4871. The A-weighted sound power

level of the mask is 25 dBA, with uncertainty 3 dBA. The

A-weighted sound pressure level of the mask at a distance of

1 m is 17 dBA, with uncertainty 3 dBA.

Environmental

Conditions Operating temperature: +41°F to 104°F (+5°C to +40°C)

Operating humidity: 15%–95% non-condensing

Storage and transport temperature: -4°F to 140°F (-20°C to

+60°C)

Storage and transport humidity: 15%–95% non-condensing.

Gross

Dimensions 380 mm (H) x 57 mm (W) x 62 mm (D). Mask fully assembled

with short tube assembly – no headgear.

Note: The manufacturer reserves the right to change these speciﬁcations

without notice.

Symbols

Caution, consult accompanying documents;

L O T

Lot number;

REF

Part

number; Temperature limitation; Humidity limitation; Does not

contain latex; Indicates a Warning or Caution and alerts you to a possible

injury or explains special measures for the safe and effective use of the device.

46810 12 14 16 18 20

ResMed Ltd (Manufacturer) 1 Elizabeth Macarthur Drive Bella Vista NSW 2153 Australia

ResMed Corp (US Designated Agent) 14040 Danielson Street Poway CA 92064-6857 USA

ResMed (UK) Ltd (EU Authorized Representative) 96 Milton Park Abingdon Oxfordshire OX14

4RY UK

ResMed Ofﬁces Australia, Austria, Belgium, Brazil, China, Finland, France, Germany, Greece,

Hong Kong, India, Ireland, Italy, Japan, Malaysia, Mexico, Netherlands, New Zealand, Norway,

Portugal, Singapore, South Africa, Spain, Sweden, Switzerland, UK, USA (see www.resmed.com

for contact details).

Swift LT Nasal Pillows System

Protected by patents: AU 785376, DE 20321468.4, DE 20321469.2, DE 20321470.6,

DE 20321471.4, DE 20321472.2, EP 1314445, NZ 562417, NZ 562418, NZ 562419, NZ 553756,

NZ 553757, NZ 553822, NZ 553824, NZ 553825, US 6581594, US 6823865, US 7159587,

US 7318437. Other patents pending.

Protected by design registrations: AU 301943, CN 200430102469.3, JP 1243026, NZ 407161,

US D552731. Others designs pending.

Swift, AutoSet CS and VPAP are trademarks of ResMed Ltd and are registered in U.S. Patent and

Trademark Ofﬁce.

Velcro is a registered trademark of Velcro Industries B.V.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere ResMed Atemwegsprodukt Handbücher

ResMed

ResMed Ultra Mirage Bedienungsanleitung

ResMed

ResMed Pixi Bedienungsanleitung

ResMed

ResMed Quattro FX NV Bedienungsanleitung

ResMed

ResMed VPAP VPAP Adapt SV System Bedienungsanleitung

ResMed

ResMed Quattro FX Bedienungsanleitung

ResMed

ResMed Quattro Air Bedienungsanleitung

ResMed

ResMed Nasal Mask Mirage Micro Bedienungsanleitung

ResMed

ResMed VPAP Adapt Bedienungsanleitung

ResMed

ResMed Silent Papillon MAP Series Bedienungsanleitung

ResMed

ResMed Swift FX Nano Bedienungsanleitung

ResMed

ResMed S7 Lightweight Bedienungsanleitung

ResMed

ResMed Ultra Mirage Bedienungsanleitung

ResMed

ResMed AirTouch N20 Montageanleitung

ResMed

ResMed Mirage Activa LT Bedienungsanleitung

ResMed

ResMed Chin Restraint Bedienungsanleitung

ResMed

ResMed S8 AutoSet Spirit Bedienungsanleitung

ResMed

ResMed Ultra Mirage II Bedienungsanleitung

ResMed

ResMed Quattro FX Bedienungsanleitung

ResMed

ResMed AirFit N30i Bedienungsanleitung

ResMed

ResMed AirFit N20 Bedienungsanleitung

ResMed

ResMed Lumis HFT Bedienungsanleitung

ResMed

ResMed Non-Vented Full Face Mask Hospital Mask Bedienungsanleitung

ResMed

ResMed Mirage Activa Bedienungsanleitung

ResMed

ResMed AirFit N20 Bedienungsanleitung

Beliebte Atemwegsprodukt Handbücher anderer Marken

Omron

Omron COMP A-I-R NE-C801 Bedienungsanleitung

CERES

CERES nosko nebulizer kit Bedienungsanleitung

Dr.Frei

Dr.Frei NE-SM1 Bedienungsanleitung

North

North 5400 series Bedienungsanleitung

John Bunn

John Bunn Neb-u-Lite LX2 Bedienungsanleitung

DeVilbiss

DeVilbiss UltraNeb Bedienungsanleitung

Sperian

Sperian Panther Hip-Pac P9684 Series Bedienungsanleitung

Dräger

Dräger X-plore 6570 Bedienungsanleitung

3M 8000 Series Bedienungsanleitung

Respironics

Respironics SideStream HS860 Bedienungsanleitung

Sundstrom

Sundstrom SR 500 Bedienungsanleitung

JARDIBRIC

JARDIBRIC KPBRU20 Bedienungsanleitung

Ombra

Ombra 63506 Bedienungsanleitung

Lotus

Lotus M-9520A Bedienungsanleitung

Philips

Philips Respironics EE Leak 1 AF541 Bedienungsanleitung

EVOLU

EVOLU Nano AiR MINI Bedienungsanleitung

Ambu

Ambu SPUR II Bedienungsanleitung

MSA AUER

MSA AUER 3S-PF Bedienungsanleitung