Rockwell Automation Allen-Bradley 513 Bedienungsanleitung

Four holes for 3/8" (9.5mm)

dia. mounting screws

Disconnecting device

operating handle in

“OFF” position

Coupling latch

Locking attachment

(Shown in the locked position)

Hole for lock

Nut and lock washer

(Locking attachment removed for clarity)

T-Bolt

Installation Instructions

Bulletin 513 Combination Starter, Size 0-2

Bulletin 598 Empty Enclosure, Size 0-2

When it is desired to remove or replace the enclosure cover, the following recommended procedures should be observed.

Removing the enclosure cover:

Swing back locking attachment on the V-Band. Loosen nut on the T-Bolt of the V-Band to permit the coupling latch to be disengaged from the head of

the T-Bolt. Pull out coupling latch from the head of the T-Bolt. Spread V-Band and place over the enclosure base, thereby freeing the cover for removal.

Remove enclosure cover and place on a at stable surface with the opening up.

CAUTION: Avoid any damage to ange surfaces as this could aect enclosure’s suitability for use in hazardous atmospheres.

Replace the enclosure cover:

Before replacing enclosure cover, clean base and cover anges with a soft cloth. Looking at the cover front in the upright position (nameplate in

readable position), place operating handle in the downward or “OFF” position. Leave in “OFF” position for maximum safety. Align ribs inside the cover

with positioning channels on the mounting plates.

CAUTION: The upright position of the cover and base plus proper positioning channel alignment are very important. Failure to observe these directions may cause

over jamming and equipment damage.

Slide cover toward base until the positioning pins in the base nearly enter the holes in the cover. At this point, when a disconnecting means is provided,

the external operating handle should be lifted slightly so that the circuit breaker operating slide mechanism becomes engaged with the roller. Continue

sliding cover toward base until the base and cover anges meet. Install V-Band over the anged joint and slide the T-Bolt into the coupling latch with

the tightening nut to the right.

CAUTION: Tighten the 3/8" (9.5) x 16 T-Bolt nut securely to provide proper enclosure sealing. NOTE: As a minimum, the helical spring lock washer beneath the nut

must be fully compressed (65 lb-in/7.3 N•m). The maximum torque applied to the nut should not exceed 125 lb-in/14.1 N•m.

Press locking attachment over the bolt and nut, and insert lock (when used) into the hole in the locking attachment.

WARNING: To prevent electrical shock, disconnect from power source before installing or servicing. Keep free from contaminants.

Installation, adjustments, putting into service, use, assembly, disassembly, and maintenance shall be carried out by suitably trained personnel in accordance with applicable code of practice. In case of malfunction or

damage, no attempts at repair should be made. The product should be returned to the manufacturer for repair. Do not dismantle the product.

4 6

1-1/2" (38 mm)

-11-1/2 N.P.T.

1-1/2" (38 mm)

-11-1/2 N.P.T.

1-1/2" (38 mm)

-11-1/2 N.P.T.

1-1/2" (38 mm)

-11-1/2 N.P.T.

3/4" (19 mm) - 14 N.P.T.

(Drain location)

3/4" (19 mm) - 14 N.P.T.

(Breather location)

Bulletin 513 Combination Starter, Size 0-2

Bulletin 598 Empty Enclosure, Size 0-2

Publication 513-IN006F-EN-P - October 2017 40050-226-01 DIR 40050-226 (Version 06)

Wiring:

A number of openings are provided in the base for power and control wiring as well as for accessories. See illustrations above. Location and quantity

of the various accessories will determine the openings available for wiring.

Openings 1 and 4 are supplied with 1-1/2" (38 mm) pipe plugs while openings 2 and 5 are supplied with 3/4" (19 mm) pipe plugs.

Openings 3 and 6 are shipped with red plastic cap plugs. These openings are generally used for power and control wiring. If not used they must be

closed with 1-1/2" (38 mm) pipe plugs.

Wiring of electrical equipment or any other accessory is to be done in accordance with instructions furnished with the equipment and applicable

codes and laws.

To comply with the NEC, CEC, IEC and ATEX Directives and to prevent the passage of gasses, vapors or ames from one portion of the electrical

installation to another, conduit openings must be sealed with an appropriate sealing tting. For use with metallic conduit only.

Mounting of a Unilock enclosure:

Mounting straps are provided on the rear of the enclosure for ease of mounting. The Unilock enclosure may be mounted to any solid surface capable

of supporting it’s weight by using 3/8" (9.5 mm) diameter screws or bolts.

Exterior dimensions of the Unilock enclosure are shown on sheet 3.

Front View Back View

Dimensions:

15-3/8"

(390.5 mm)

2-7/16"

(61.9 mm)

3/8"

(9.5 mm)

2-5/8"

(66.7 mm)

5-1/4"

(133.4 mm)

13-1/4"

(336.6 mm)

7-1/4"

(184.2 mm)

Mounting

5-7/8"

(149.2 mm)

11-3/4"

(298.4 mm)

Mounting

Four 3/8" (9.5 mm)

Mounting screws

6-7/16"

(163.5 mm)

8-1/16"

(204.8 mm)

3-5/8"

(92.1 mm)

Publication 513-IN006F-EN-P - October 2017 40050-226-01 DIR 40050-226 (Version 06)

Bulletin 513 Combination Starter, Size 0-2

Bulletin 598 Empty Enclosure, Size 0-2

40050-226-01

DIR 40050-226 (Version 06)

Allen-Bradley, Rockwell Software, and Rockwell Automation are trademarks of Rockwell Automation, Inc.

Trademarks not belonging to Rockwell Automation are property of their respective companies.

Publication 513-IN006F-EN-P - October 2017

Rockwell Automation maintains current product environmental information on its website at http://www.rockwellautomation.com/rockwellautomation/about-us/sustainability-ethics/product-environmental-compliance.page.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Rockwell Automation Controller Handbücher

Rockwell Automation

Rockwell Automation SLC 500 Thermocouple Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix 1400 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Guardmaster 440G-MZ Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley OneGear Bedienungsanleitung

Rockwell Automation

Rockwell Automation MPMA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley MicroLogix Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 45MLA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley DriveLogix 5730 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1763-L16AWA Bedienungsanleitung

Rockwell Automation

Rockwell Automation Reliance SP500 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 750-Series Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SMC-Flex 150 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley ARMORSTART Bedienungsanleitung

Rockwell Automation

Rockwell Automation GV3000/SE 230 Installations- und Betriebshandbuch

Rockwell Automation

Rockwell Automation Allen-Bradley PowerFlex 23PFC Betriebsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley Micro800 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 150-E Bedienungsanleitung

Rockwell Automation

Rockwell Automation ARMORSTART Betriebsanleitung

Rockwell Automation

Rockwell Automation MicroLogix 1000 Bedienungsanleitung

Rockwell Automation

Rockwell Automation PowerFlex 700S Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley SMC-3 Bedienungsanleitung

Rockwell Automation

Rockwell Automation Allen-Bradley 1769-OA16 Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L23E-QB1B Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch