Rosewill RNX-N150PCe Bedienungsanleitung

2.4GHz Wireless Lite-N PCI-E Adapter

RNX-N150PCe

Quick Installation Guide

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

The Quick Installation Guide will help you to install RNX-N150PCe 150M Wireless

Lite-N PCI-E Adapter, including basic hardware and software installation, as well as

configuration of wireless network availability. The Quick Installation bases on

establishing an unencrypted wireless network. For detailed instructions, please refer

to the User Guide in the Resource CD.

A. Hardware Installation

1. Turn off your desktop PC and disconnect the power.

2. Remove your PC case and locate an available PCI-E slot on the mianboard.

Remove the metal slot cover on the back of the PC. Check with your computer

manufacturer for instructions if needed.

3. Slide the PCI-E Adapter into the PCI-E slot. Make sure that all of its pins are

touching the slot's contacts. Once the adapter is firmly in place, secure its

fastening tab to your PC's chassis with a mounting screw. Then, close your PC

case.

4. Reconnect your PC’s power and turn on your desktop PC.

B. Software Installation for Windows XP

1. Insert the Resource CD into your CD-ROM drive. Find the CD/DVD drive where

the installation CD was placed. Open RNX-N150PCe folder, and double-click

Setup.exe. Then the following screen for preparing setup will appear.

Figure 1

2. Follow the step-by-step instructions to complete InstallShield Wizard steps.

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

Note:

1) If Windows XP warns about Windows Logo testing, click Continue Anyway

to continue the installation.

2) After the Installation, or will appear at the bottom of the screen in

your system tray. Otherwise, there may be some problems about the

installation, please check it seriously.

C. Configure wireless connection in Windows XP

a. Configure

using

Wireless Lite-N Client Utility

The Adapter's tray icon shows the signal strength using color and the received

signal strength indication (RSSI). If the icon is (green), a wireless connection

has been established. If the icon is (gray), there is no connection. Follow the

steps below to launch a wireless connection manually.

1. Double-click the icon , then the Wireless Lite-N Client Utility will appear, you

can also run the utility by clicking Start→All programs→Rosewill→Wireless

Lite-N Client Utility. On the prompted configuration tab page, click the Profile

Management, and you will see the next screen (Figure 2).

Figure 2

2. Click Scan on the screen above, and you will see a new screen (shown in

Figure 3), click Refresh, then the latest available Network will appear.

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

Figure 3

3. In the screen above, highlight a network name and click Activate, then you will

see the next screen (shown in Figure 4). Enter the Client Name and SSID, click

OK and you can connect to the network.

Figure 4

Note: If a well-balanced wireless network cannot be created, please refer to the User

Guide on the Resource CD or your dealer for help.

b. Configure using Windows XP Wireless Zero Configuration

1. Windows XP will display a wireless Network Connection message (shown in

Figure 5). To use Windows XP Wireless Zero Configuration, right-click on the

wireless computer icon in your system tray (lower-right corner), and then select

View Available Wireless Networks in the next screen.

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

Figure 5

2. After that, you will see the next screen (shown in Figure 6) with many available

wireless network choices. You can highlight a network and then click Connect

to add to a network.

Note: If you have not installed SP2 for Windows XP, the screens below will not be

available.

Figure 6

3. If the connection is finished, the icon will display like the next screen shown.

Figure 7

Note: If a well-balanced wireless network cannot be created, please refer to the User

Guide on the Resource CD or your dealer for help.

D. Software Installation for Windows 2000

The Software Installation for Windows 2000 is similar to Windows XP, you can refer

to the “B Software Installation for Windows XP” to complete the installation.

Note: During the installation, If Windows 2000 prompts "Digital Signature Not

Found", click Yes to continue the installation.

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

E. Configure wireless connection in Windows 2000

After installing the adapter, the adapter's tray icon will appear in your system

tray. To use the Wireless Lite-N Client Utility, double-click it. The steps for windows

2000 and windows XP are very similar. Please refer to “a Configure using Wireless

Lite-N Client Utility” in “C Configure wireless connection in Windows XP”.

F. Software Installation for Windows Vista

1. Insert the Resource CD into your CD-ROM drive. Find the CD/DVD drive where

the installation CD was placed. Open RNX-N150PCe folder, and double-click

Setup.exe. Then the following screen for preparing setup will appear.

Figure 8

2. Follow the step-by-step instructions screen to complete InstallShield Wizard

steps.

Note: If Windows Vista warns about Windows Logo testing, click Install this driver

software anyway to continue the installation.

G. Configure wireless connection in Windows Vista

After the Adapter's driver has been installed, Windows Vista will display a wireless

Network Connection message. Icon (green) means the connection has been

established. Icon (gray) means there is no connection. To use Windows WLAN

Autoconfig to establish a connection, please follow the steps below.

1. Right-click the icon in your system tray, then click “Connect to a network”.

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

Figure 9

2. The following screen (shown in Figure 10) will show you available wireless

networks. Highlight the one you want to join in, and then click Connect.

Figure 10

3. To continue, click Connect Anyway. To end the connection, click Cancel.

4. If the connection is successfully established, the following screen will appear.

Click Close to finish the connection.

Figure 11

Note: For more information about Windows Vista WLAN Autoconfig on a Windows

Vista computer, refer to Help and Support of the Operating System. If a

well-balanced wireless network cannot be created, please refer to the User

Guide on the Resource CD or your dealer for help.

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

H. Software Installation for Windows 7

1. Insert the Resource CD into your CD-ROM drive. Find the CD/DVD drive where

the installation CD was placed. Open RNX-N150PCe folder, and double-click

Setup.exe. Then the following screen for preparing setup will appear.

Figure 12

2. Follow the step-by-step instructions in the continued prompted screens to

complete InstallShield Wizard steps.

I. Configure wireless connection in Windows 7

After the Adapter's driver has been installed, please follow the steps below to use

Windows WLAN Autoconfig to establish a connection.

1. Click the icon at the bottom of your screen in your system tray and then

you will see the available wireless network list. Select the SSID of your Access

Point, take test for example. Click Connect.

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

Figure 13

2. If your wireless network is secured, you will be required to enter the security key

as shown in Figure 14. Enter the passphrase, take 1234567890 for example.

And then click OK.

Figure 14

3. If the key entered is correct, you will successfully connect to the network as

shown in Figure 15.

2.4GHz Wireless Lite-N PCI-E Adapter RNX-N150PCe Quick Installation Guide

Figure 15

Note: For more information about Windows 7 WLAN Autoconfig on a Windows 7

computer, refer to Help and Support of the Operating System.

J. WPS configuration

WPS (Wi-Fi Protected Setup) function allows the Adapter to join a wireless network

quickly.

Note: WPS function is not supported in Windows 7 OS.

If the wireless card supports Wi-Fi Protected Setup (WPS), you can establish a

wireless connection between wireless card and router using either Push Button

Configuration (PBC) method or PIN method.

First, the WPS software should be installed. Insert the Resource CD into your

CD-ROM drive. Double-click My Computer, and then double-click the CD/DVD drive

where the installation CD was placed. Open RNX-N150PCe folder, and double-click

wps.exe. Then you will see Figure 16.

Andere Handbücher für RNX-N150PCe

Inhaltsverzeichnis

Andere Rosewill PCI-Karte Handbücher

Rosewill

Rosewill RC-302 Bedienungsanleitung

Rosewill

Rosewill RC-304 Bedienungsanleitung

Rosewill

Rosewill RC205 Bedienungsanleitung

Rosewill

Rosewill RC-401 Bedienungsanleitung

Rosewill

Rosewill RC-305E Bedienungsanleitung

Rosewill

Rosewill RC-20003 Bedienungsanleitung

Rosewill

Rosewill RC-209-EX Bedienungsanleitung

Rosewill

Rosewill SATA II 4 Port PCI RAID Card RC217 Bedienungsanleitung

Rosewill

Rosewill RC-NIC412 Bedienungsanleitung

Rosewill

Rosewill RC-101 Bedienungsanleitung

Rosewill

Rosewill RC-213 Bedienungsanleitung

Rosewill

Rosewill RC503 Bedienungsanleitung

Rosewill

Rosewill RNWD-N9003 PCE Bedienungsanleitung

Rosewill

Rosewill RC-303 Bedienungsanleitung

Rosewill

Rosewill RC-302E Bedienungsanleitung

Rosewill

Rosewill RC400 Bedienungsanleitung

Rosewill

Rosewill RNWD?N9003PCE Bedienungsanleitung

Rosewill

Rosewill RC-301 Bedienungsanleitung

Rosewill

Rosewill RC-110 Bedienungsanleitung

Rosewill

Rosewill RC501 Bedienungsanleitung

Rosewill

Rosewill RNX-N300 Bedienungsanleitung

Rosewill

Rosewill RC-223 Bedienungsanleitung

Rosewill

Rosewill RNX-G100 Bedienungsanleitung

Rosewill

Rosewill RC-20002 Bedienungsanleitung

Beliebte PCI-Karte Handbücher anderer Marken

ERMA

ERMA SSI 1417 Bedienungsanleitung

SIIG

SIIG CyberSerial Dual PCI Montageanleitung

I-Bus

I-Bus IBC2602 Bedienungsanleitung

Exsys

Exsys EX-60102 Bedienungsanleitung

Chelsio Communications

Chelsio Communications T5 Series Bedienungsanleitung

Conrad Electronic

Conrad Electronic 97 46 71 Bedienungsanleitung

Micro Innovations

Micro Innovations USB650A Bedienungsanleitung

KTI Networks

KTI Networks KF-310 Bedienungsanleitung

Asus

Asus SpaceLink WL230 Bedienungsanleitung

SIIG

SIIG SC2475 Bedienungsanleitung

TRENDnet

TRENDnet TEW-703PI Bedienungsanleitung

Belkin

Belkin F5D7000F Bedienungsanleitung

Pericom

Pericom PI7C7100 Bedienungsanleitung

ADLINK Technology

ADLINK Technology cPCI-3548 Bedienungsanleitung

Digium

Digium TE200 Series Bedienungsanleitung

Allo.com

Allo.com 2nd Gen E1/T1/J1 Bedienungsanleitung

Western Digital

Western Digital FireWire PCI Adapter Bedienungsanleitung

Pyle

Pyle Gamelink PLINK1 Bedienungsanleitung