S.R.Smith CYCLONE Gebrauchsanweisung

06-510 OCT19

CYCLONE

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

SRS AUSTRALIA, PTY LTD

12 Enterprise St

Richlands QLD 4077

Australia

Phone 07 3812 2283 • Fax 07 3812 1187

www.srsmith.com/au

S.R. SMITH, LLC

CORPORATE HEADQUARTERS

P.O. Box 400 • 1017 S.W. Berg Parkway

Canby, Oregon 97013

USA

Phone (503) 266 2231 • Fax (503) 266 4334

www.srsmith.com

S.R. SMITH CYCLONE SLIDES ARE MANUFACTURED FOR

INSTALLATION AND USE ON RESIDENTIAL INGROUND SWIMMING

POOLS ONLY. THE CYCLONE IS NEVER TO BE INSTALLED AND USED

ON ABOVEGROUND POOLS, ONGROUND POOLS, HOUSEBOATS, BOAT

DOCKS, FLOATING DOCKS OR PLATFORMS OR OTHER BODIES OF

WATER SUCH AS LAKES, PONDS, RIVERS, ETC.

TABLE OF CONTENTS

INTRODUCTION...........................................................................................................................................3

INSTALLED CYCLONE STRUCTURAL & INSTALLATION CHECKLIST...................................................4

MAINTENANCE INSTRUCTIONS................................................................................................................4

ASSEMBLED CYCLONE LAYOUT..............................................................................................................5

PARTS LIST..................................................................................................................................................6

ASSEMBLY INSTRUCTIONS.......................................................................................................................7

Tools Required..........................................................................................................................................7

Gasket Installation.....................................................................................................................................7

Cyclone Assembly.....................................................................................................................................8

ON-DECK MOUNTING INSTRUCTIONS.....................................................................................................9

SLIDE PLUMBING INSTRUCTIONS..........................................................................................................10

MANUFACTURER’S PLACEMENT INSTRUCTIONS ...............................................................................11

Visit srsmith.com for information on the complete line of

S.R.Smith pool products.

SLIDE ASSEMBLY AND INSTALLATION VIDEOS AVAILABLE AT

www.youtube.com/srsmithllc

www.srsmith.com/en/customer-service/product-registration

INTRODUCTION

DANGER –FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE

OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.

CYCLONE IS DESIGNED AND MANUFACTURED FOR INSTALLATION AND USE ON INGROUND

SWIMMING POOLS ONLY. DO NOT INSTALL THIS SLIDE ON ABOVE GROUND POOLS,

HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES OF

WATER SUCH AS LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE,

AND SUPERVISION ARE ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE RISK OF

SERIOUS INJURY OR DEATH.

ALL NATIONAL AND LOCAL BUILDING CODES MUST BE FOLLOWED. THIS INCLUDES ANY

APPLIABLE REQUIREMENTS FOR SIZE OF CONCRETE FOOTING, OVERALL HEIGHT OF SLIDE,

AND BODING OR ELECTRICAL CODES.

CHECK INSIDE ALL BOXES AND PACKAGING MATERIALS FOR PARTS. BEFORE BEGINNING

ASSEMBLY, READ ALL INSTRUCTIONS AND IDENTIFY PARTS USING THE FIGURES AND PARTS

LISTED IN THIS DOCUMENT. IT IS CRITICAL THAT ALL PARTS BE CAREFULLY INSPECTED BY

THE INSTALLER PRIOR TO INSTALLATION TO ENSURE THAT NO DAMAGE OCCURRED IN

TRANSIT AND THAT A DAMAGED PART IS NOT USED. PROPER INSTALLATION CANNOT BE

OVERSTRESSED, IMPROPER INSTALLATION VOIDS S.R. SMITH’S WARRANTY AND MAY

AFFECT THE SAFETY OF THE USER.

INSTALLER MUST GIVE TO SLIDE OWNER: CYCLONE INSTALLATION AND OWNER’S MANUAL,

THE WARRANTY CARD, AND ANSWER ALL QUESTIONS REGARDING SAFE AND PROPER USE

AND SLIDE MAINTENANCE.

FOR COMPLETE SLIDE SAFETY INFORMATION REFER TO THE OWNER’S MANUAL.

INSTALLED CYCLONE STRUCTURAL & INSTALLATION CHECKLIST

Installer to review with slide owner upon completion of slide installation.

1. Inspect the runway for visible cracks or tears.

2. Inspect the ladder for sharp edges, protrusions, cracks, or tears.

3. Inspect all fasteners to make sure they are fully tightened.

4. Inspect the ladder for rigidity and attachment.

5. Measure the following dimensions and compare with the manufacturer’s placement instructions on

page 11.

•Measure the depth of water in front of the slide exit. (3’-6” min. depth at a distance of 4’-6”

from exit end of slide.)

•Measure the height of the slide runway exit above the water. (20” max.)

•Measure the distance between the slide centerline and the edge of other pool equipment

6. Observe the position of the exit of the slide as shown in FIGURE F, FIGURE G, and FIGURE I on

pages 11 and 12.

MAINTENANCE INSTRUCTIONS

1. When hosing down the deck, hose your Cyclone to wash away any dust, dirt or other debris, which

may have accumulated.

2. Be sure that all connections are secure. Tighten hardware if necessary.

3. All polyethylene parts require little maintenance. Hose and wipe to clean.

While cleaning slide, check and see that all nuts and bolts are tight and secure.

4. Inspect the runway for visible cracks or tears, sharp edges and protrusions.

5. Inspect all attachment points for loose or corroded fasteners.

6. Inspect all ladder tread or step-attachment points for evidence of shear, bending yield, or fatigue in

the ladder steps, rails, or attachments means. Yield is evidenced by crystallization or fine cracking of

the ladder tread and/or surface.

7. Inspect the ladder handrails for rigidity and attachment.

ASSEMBLED CYCLONE LAYOUT

FIGURE A

PARTS LIST

Visit srsmith.com for hardware kit and replacement part information.

ITEM NO.

PART NO.

DESCRIPTION

QTY.

KIT A

KIT B

KIT A

69-209-113

CYCLONE HARDWARE KIT

1 ea.

KIT B

69-209-710

CYCLONE WATER KIT

1 ea.

5-139

3/8” HEX NUT

2 ea.

●

5-151

3/8” LOCK WASHER

2 ea.

●

05-14-115

1/2" LOCK WASHER

7 ea.

●

5-145

3/8” FLAT WASHER

16 ea.

●

5-245

3/8” x 2-1/2” LAG SCREW

10 ea.

●

5-240

3/8” x 3-1/2” LAG SCREW

2 ea.

●

5-260

3/8” x 6.5” HEX HEAD CAP SCREW

2 ea.

●

5-241

1/2"-13 ANCHOR 5" LONG W/NUT & WASHER

7 ea.

●

05-711

PVC NIPPLE SCH 80-3/4” x 2”

1 ea.

●

05-712

3/4” FHT x 3/4”FIPT SWIVEL 90

1 ea.

●

8-531

GASKET

2 ft.

5-371

HOSE CLIP SCREW

1 ea.

●

05-713

3/4” HOSE CLIP

1 ea.

●

(1)

(5)

(7)

(8)

(3)

(2)

(4)

(10)

(9)

(12)

))

(11)

(6)

(13)

))

ASSEMBLY INSTRUCTIONS

Tools Required

1. Ratchet handle

2. 9/16” deep socket

3. 9/16” wrench

4. 1/2" socket or wrench

5. 1/2" concrete drill bit

6. 1/4" drill bit

7. Phillips screw driver

8. Power drill

9. Lint free rag

10. Pistol-grip clamp (optional)

Gasket Installation

•Clean the groove of the top runway section, shown below, with a damp clean rag and dry

•Take the 2 feet of gasket provided with your kit and begin to peel back the paper. Make sure you

are not removing the adhesive itself from the gasket.

•Take the exposed gasket & adhesive and begin at a top edge of the runway section groove.

•While firmly pressing the gasket into the groove, intermittently press and remove more paper,

exposing adhesive, until you have used the entire gasket.

•Properly installed, the gasket will extend from one side of the slide to the other and be centered in

the groove, front to back.

•Continue to assemble your Cyclone as described on page 8, and ensure the gasket remains in

place as you handle the sections.

FIGURE B

NOTE:

BE SURE TO APPLY ANTI-SEIZE TO ALL

FASTENERS TO PREVENT GALLING.

NOTE:

Use pistol-grip clamps as necessary to align the molded parts.

Top Runway Section

(11)

1. Clean the groove

2. Place Gasket into

Groove

Cyclone Assembly

1. Place the upper & lower slide runway sections on the ground. Assemble and fasten as shown in

FIGURE C.

2. a. Attach the pedestal to the upper & lower slide sections as shown in FIGURE D in 2

locations.

b. Attach the pedestal as shown in FIGURE D in 4 locations. Mark and drill a 1/4" pilot hole

in the center of each recess before fasting with the lag screws.

3. Attach the assembled slide runway to the ladder using the hardware shown in FIGURE E.

(5)

(4)

(5)

(4)

(6)

2.a.

2.b.

(7)

(4)

(1)

(2)

(4)

(5)

(4)

FIGURE D

FIGURE E

FIGURE C

ON-DECK MOUNTING INSTRUCTIONS

1. Place the assembled slide on the deck relative to the pool wall. Ensure that the

exit flume clears any coping. Slide may be angled slightly providing all

dimensions are maintained as noted in the Manufacturer’s Placement

Instructions noted in the following section.

2. With the slide in its proper location, center punch or otherwise mark through the

(7) mounting holes at the bottom of the ladder and base so that a visible mark

is apparent on the concrete.

3. Move the assembled slide aside to facilitate drilling of the anchoring holes.

4. Using a power drill and a 1/2” concrete drill bit, drill the holes to a depth of 4”.

Use tape or a marking on the drill bit to ensure that the hole for the anchor is

drilled to the required depth. Maintain drill hole straight and perpendicular for

proper holding strength of anchor stud.

5. Clear the holes of all debris. Assemble anchor with nut and washer so that the

top of the nut is flush with the top of the anchor. Move the slide over the holes

and insert the anchors. Drive anchor through the slide mounting holes so that

nut and washer are flush with the surface material.

6. Expand anchor by tightening nut 3 to 5 turns. Once anchor is set remove nut

and install a lock washer, item # (3), and retighten nut to a torque of 55 ft.-lbs.

SLIDE PLUMBING INSTRUCTIONS

1. Thread the nipple (9) into swivel (10).

2. Note the angle of the threaded hole in the top

runway section.

3. Align the nipple with the hole-angle from the

outside of the slide as shown in the top

illustration.

4. Insert the nipple into the slides hole and firmly

thread the nipple using the swivel (10) to turn.

**This action is self-sealing and no Teflon or

Plumbing glue is required**

5. Note the pressure required as you turn the fitting

assembly, this is letting you know a tight fit is

being formed.

**The fitting material is harder than the slide material

and makes its own threading; that is why it is good to

get this right the first time, but not imperative**

6. Turn the fitting assembly (9 & 10) until the swivel

(10) comes in contact with the wall of the Cyclone

7. Gently tilt the swivel (10) away from the slide and

complete one more turn to ensure a good

insertion.

8. Finish turning the swivel (10) with the fitting

assembly pointed back toward the bottom of the

stairs as shown in the bottom illustration.

**Threads still showing between the nipple

(9) and slide wall after step 8 (above) are

better left exposed than over tightening

and stripping the hole or scraping the slide

wall with the swivel (10)**

9. Place the hose clip in a location where

it will support the hose without putting

a “kink” into its shape; screw it directly

into the slide stairs making sure not to

over tighten the screw.

**The purpose of the clip is to take shock

transferred through the hose from sudden

jerks**

10. Turn on the water so that it lands in the

center of the slide runway and ENJOY

Nipple (9)

Swivel (10)

Outside Runway

Inside Runway

Outside Runway

Inside Runway

Contact?

Stop!

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere S.R.Smith Beleuchtungsausrüstung Handbücher

S.R.Smith

S.R.Smith TURBOTWISTER Gebrauchsanweisung

S.R.Smith

S.R.Smith SlideAway Installationsanleitung

S.R.Smith

S.R.Smith EDGE 6 Programmierhandbuch

S.R.Smith

S.R.Smith LM10 Bedienungsanleitung

S.R.Smith

S.R.Smith R Series Bedienungsanleitung

S.R.Smith

S.R.Smith pLX-PL60 Kurzanleitung

S.R.Smith

S.R.Smith SWIM CLUB II FUNSLIDE Bedienungsanleitung

S.R.Smith

S.R.Smith VORTEX Gebrauchsanweisung

S.R.Smith

S.R.Smith SRS-TX-30 Bedienungsanleitung

S.R.Smith

S.R.Smith Star Series Bedienungsanleitung

S.R.Smith

S.R.Smith multiLift 2 Leitfaden

S.R.Smith

S.R.Smith ROGUE GRAND RAPIDS Bedienungsanleitung

S.R.Smith

S.R.Smith 6004 Series Bedienungsanleitung

S.R.Smith

S.R.Smith FRONTIER II Bedienungsanleitung

S.R.Smith

S.R.Smith heliX2 Gebrauchsanweisung

S.R.Smith

S.R.Smith PT-6001 Power Tower Bedienungsanleitung

S.R.Smith

S.R.Smith TYPHOON Gebrauchsanweisung

S.R.Smith

S.R.Smith PAL Series Bedienungsanleitung

S.R.Smith

S.R.Smith Power Tower PT-6002 Bedienungsanleitung

S.R.Smith

S.R.Smith BYOS 2 Programmierhandbuch

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith AQUABLAST Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung