S.R.Smith Star Series Bedienungsanleitung

Star Series™

Fiber J-Box

(CLSFJB or CLSFJB2) Use only with Class 2 power units

Installation Instructions

Read all instructions before attempting to perform installation work

Suitable for Wet Locations • Suitable for Outdoor Use • Type 3R Rainproof Enclosure

FOR USE WITH POOL AND SPA PRODUCTS

4005496

ETL LISTED

Conforms to UL STD 2108;

Certied to CSA STD C22.2 #250.0

79-15278-00 REV6/18

Contents

IMPORTANT SAFETY INFORMATION ................................3

Electrical Ratings ........................................................4

Recommended Tools and Supplies ......................................4

INSTALLATION INSTRUCTIONS.......................................5

Enclosure mounting .....................................................5

Input / Low Voltage Supply Line .........................................7

Fiber Optic Cable Conduit Connection .................................7

Final Steps ...............................................................8

IMPORTANT SAFETY INFORMATION

CAUTION: POWER AND SIGNAL OUTPUT CONDUITS MUST BE NON-METALLIC

ATTENTION: CONDUITS POUR PUISSANCE DE SORTIE ET SORTIE SIGNAL DOIT ETRE NON METALLIQUE

ELECTRICAL SHOCK HAZARD – SWITCH DOES NOT TURN OFF INPUT POWER.

Failure to disconnect input power before servicing can lead to serious injury, or death.

Disconnect input power before servicing.

Replace all parts and panels before reconnecting power and operating

DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE

OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.

Basic safety precautions shall be observed when installing and operating the connected LED Water

Feature (CLSFJB / CLSFJB2) and/or other associated equipment:

1. A qualied electrician must install the CLSFJB in accordance with the requirements of NEC

ANSI/NFPA 70 and Article 680.

2. The CLSFJB must be mounted on a at vertical surface. The unit must be a minimum of 4

inches above the ground level, pool deck, or higher than 8 inches above the maximum pool

water level, whichever provides greatest elevation. The unit must be positioned a minimum of

4 feet (1.2 m) from the inside wall of the pool, unless separated from the pool by a solid fence,

wall, or other permanent barrier.

3. Do not exceed the maximum electrical ratings of the LED luminaire/s housed within this

CLSFJB / CLSFJB2, or components, wiring devices, and current carrying capacity of the

conductors.

4. This CLSFJB is intended to be used with low voltage damp rated luminaires that comply with

Article 680 of the National Electrical Code and does not require bonding due to their isolated

application design.

5. For supply connection, use only with Class 2 power units.

6. DO NOT CONNECT THIS 12V LIGHT DIRECTLY TO A 120VAC CIRCUIT - LIGHT WILL BE

DAMAGED.

7. This device should never operate equipment that could cause property damage, bodily injury,

or death should it be activated unexpectedly.

8. Use rain-tight or wet location hubs that comply with the requirements in the standard for

conduit, tubing, and cable ttings (UL514b) only.

9. The conduit hub is to be connected to the power input conduit before the hub is connected to

the enclosure.

Electrical Ratings

Do not exceed the maximum electrical output rating of each unit listed below.

Model Input

CLSFJB 12VAC, 60 Hz, 0.42A max

CLSFJB2 12VAC, 60 Hz, 0.42A max (x2)

Recommended Tools and Supplies

1. Circular hole saw for installation of 3/4” and or 1” non-metallic conduit depending on installation

requirements. Do not use spade bits for opening the conduit knockouts.

2. Application appropriate and approved ‘rain-tight’ or ‘wet location’ conduit hubs.

* Note: Every installation will have at least two (multi) conduits – one or more for low voltage

input power and one or more for ber optic cable.

3. Slotted screw driver, size #2

4. Phillips screw driver, size #2

5. Drill

6. #10 Screws appropriate for installing the product onto a wall (Installer supplied)

* Note: It is recommended to hand tighten all screws and screw fasteners inside the enclosure

and front cover until snug and secure. Be sure not to overtighten as permanent damage may

occur.

INSTALLATION INSTRUCTIONS

WARNING

• TURN OFF INCOMING POWER BEFORE SERVICING EQUIPMENT.

• ALL INSTALLATION AND MAINTENANCE WORK MUST BE PERFORMED BY A

QUALIFIED ELECTRICIAN.

• VERIFY ALL ELECTRICAL RATINGS BEFORE INSTALLATION IS COMPLETE.

• FOLLOW PROPER WIRING PRACTICES IN ACCORDANCE WITH ALL NATIONAL AND

LOCAL REGULATORY REQUIREMENTS.

Enclosure mounting

1. Locate the CLSFJB / CLSFJB2 in an appropriate area that meets the following requirements:

a. Must be mounted on a at vertical surface.

b. Must be a minimum of 4 inches above the ground level, pool deck, or higher than 8 inches

above the maximum pool water level, whichever provides greatest elevation.

c. Must be positioned a minimum of 4 feet (1.2 m) from the inside wall of the pool unless

separated from the pool by a solid fence, wall, or other permanent barrier.

For the unit to be adequately air cooled, allow a minimum gap of 9/32” (7.2mm) between the wall

and the back surface of the unit. The stand-off mounting tabs will make contact with the wall.

WALL

Minimum Gap of 9/32" or 7.2mm

2. By hand open the enclosure by pulling the front cover off evenly by the top and bottom tabs.

Do not angle or ‘hinge’ the cover when removing or damage may occur. If you cannot open

the enclosure by hand, use a at blade screwdriver to twist open the nger tabs of the cover

at the top and bottom of the unit.

3. Securely install a wall material appropriate #10 screw, supplied by the installer, into the

location where the unit will be installed. The screw head must be 1 1/8” away from the wall to

allow the unit to be mounted correctly.

4. Place the mounting tab of the CLSFJB over the #10 screw and let it hang in place. Level the

unit and mark the remaining 2 mounting screw locations on the wall. Use 2 more material

appropriate #10 screws, supplied by the installer, to secure the unit to the wall through the

mounting holes on the back of the unit. Once the lower two screws are secure, tighten the top

screw to securely hold the upper portion of the enclosure in place.

Top View

Enclosure

Front View

Enclosure

Bottom View

Enclosure

Top Tab

Bottom Tab

Input / Low Voltage Supply Line

1. Bring the low voltage supply power conduit to one of the two, lower right or left side input

power conduit knockout locations. On CLSFJB2 models, one or two conduits may be used for

the low voltage luminaire input power depending on power source locations and if separated

lighting controls are required. DO NOT use any of the bottom conduit connection locations for

input power – these are reserved for the ber conduit (output) locations.

*Note: The wiring of the 12VAC input and ber cable/s are required to use separate conduits

and must not share an individual conduit. No conduit should contain both 12VAC input power

and ber optic cables.

2. Using a hole saw, open the knockouts for the size of the conduit (¾” or 1”) being installed.

3. Attach an approved ‘rain-tight’ or ‘wet location’ hub to the conduit. After the hub is attach

to the conduit, attached the hub to the enclosure.

Locations of Input

Power Knockouts

Locations of Output

Power Knockouts

Fiber Optic Cable Conduit Connection

1. The enclosure provides four (4) possible Fiber Optic cable conduit locations, two (2) on the

bottom left and two (2) on the bottom right portion of the enclosure.

2. Using a hole saw, open the knockout for the size of the conduit (¾” or 1”) being installed.

3. Bring the Fiber Optic cable conduits to the open conduit locations.

4. Attach an approved ‘Rain-tight’ or ‘wet location’ hub to the conduit rst, and then attach hub to

the enclosure.

Fiber Optic cable conduit locations

Final Steps

1. Pull 12VAC cable into input power conduit and connect to

the appropriate power supply.

2. Pull in ber optic cable from the water feature and insert port

tip into the black compression tting - tighten until rmly

held in place. Do not overtighten as damage to the ber optic

cable may result.

S.R.Smith, LLC

P.O. Box 400 | Canby, OR 97013

P 503.266.2231 TF 800.824.4387

srsmith.com

79-15278-00 REV6/18

Questions?

Contact One of Our Dedicated Lighting Specialists. 1-800-824-4387 x4012 or x2282

3. In some cases there may

be excess ber optic

cable. DO NOT CUT

the cable, instead coil

the excess in as large of

a loop as possible and

place in the open area of

the enclosure. DO NOT

KINK. If more space is

required due to lots of

excess ber, it may be

helpful to add a larger

pull box in between the

conduit and CLSFJB or

CLSFJB2 to house the

excess ber.

4. Snap the ber optic light source (CLS-2xx) into

the metal bracket and adjust the position until

both of the locating tabs on the ends of bracket

capture the top and bottom of the CLS-2xx

housing. Use cable tie (zip-tie) to close and

tighten the open ends of the mounting bracket.

WARRANTY INFORMATION

For Lighting product warranty information and details, please visit our website:

www.srsmith.com/warranty

FJB FJB2

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere S.R.Smith Beleuchtungsausrüstung Handbücher

S.R.Smith

S.R.Smith TYPHOON Gebrauchsanweisung

S.R.Smith

S.R.Smith EDGE 6 Programmierhandbuch

S.R.Smith

S.R.Smith PT-6001 Power Tower Bedienungsanleitung

S.R.Smith

S.R.Smith LM10 Bedienungsanleitung

S.R.Smith

S.R.Smith Power Tower PT-6002 Bedienungsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith FRONTIER II Bedienungsanleitung

S.R.Smith

S.R.Smith SWIM CLUB II FUNSLIDE Bedienungsanleitung

S.R.Smith

S.R.Smith SRS-TX-30 Bedienungsanleitung

S.R.Smith

S.R.Smith BYOS 2 Programmierhandbuch

S.R.Smith

S.R.Smith R Series Bedienungsanleitung

S.R.Smith

S.R.Smith pLX-PL60 Kurzanleitung

S.R.Smith

S.R.Smith AQUABLAST Bedienungsanleitung

S.R.Smith

S.R.Smith CYCLONE Gebrauchsanweisung

S.R.Smith

S.R.Smith VORTEX Gebrauchsanweisung

S.R.Smith

S.R.Smith heliX2 Gebrauchsanweisung

S.R.Smith

S.R.Smith SlideAway Installationsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith TURBOTWISTER Gebrauchsanweisung

S.R.Smith

S.R.Smith ROGUE GRAND RAPIDS Bedienungsanleitung

S.R.Smith

S.R.Smith multiLift 2 Leitfaden

S.R.Smith

S.R.Smith PAL Series Bedienungsanleitung

S.R.Smith

S.R.Smith 6004 Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung