S.R.Smith ROGUE GRAND RAPIDS Bedienungsanleitung

THE ROGUE

GRAND RAPIDS

SLIDE OWNER’S MANUAL

CORPORATE HEADQUARTERS

WESTERN SALES AND MANUFACTURING PLANT

P.O. Box 400 •

••

•1017 SW Berg Parkway

Canby, Oregon 97013

(503) 266-2231 •

••

•(503) 266-4334

www.srsmith.com

06-677 

S.R. SMITH, LLC 2005

JUN11

* * C A U T I O N * *

S.R. SMITH ROGUE

GRAND RAPIDS

ARE MANUFACTURED FOR

INSTALLATION AND USE ON RESIDENTIAL INGROUND POOLS

ONLY. ROGUE

GRAND RAPIDS

ARE NEVER TO BE INSTALLED

AND USED ON PUBLIC INGROUND POOLS, ABOVEGROUND POOLS,

ONGROUND POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING

DOCKS OR PLATFORMS

Table of Contents

Topic Page #

Introduction………………………………………………………….. 2

Applicable Standards and Codes…………………………………. 2

Installation……………………………………………………….…… 2

Drawings……………………………………………………………… 2

Subsequent Owners………………………………………………… 2

Manufacturer’s Placement Instructions…………………………… 3

Installed Slide’s Structural & Installation Checklist………………. 5

Intended Use Instructions………………………………………….. 5

Sitting Slide Position………………………………………………… 6

Do Not Slide Head First…………………………………………….. 7

Daily/Weekly Maintenance Of Slide………………………………... 7

Cleaning Instructions………………………………………………… 8

INTRODUCTION

S.R. Smith Rogue

Grand Rapids

is manufactured for installation and use on

residential inground swimming pools only. S.R. Smith Rogue

Grand Rapids

NEVER to be installed and used on public inground pools, aboveground pools, on

ground pools, houseboats, boat docks, floating docks or platforms.

APPLICABLE STANDARDS AND CODES

1. All S.R. Smith Rogue

Grand Rapids

are manufactured in accordance with

Consumer Products Safety Commission

STANDARD FOR SWIMMING POOL SLIDES

, 16

CFR Ch. 11 Part 1207 (latest edition).

2. Installer must comply with all applicable governmental and building codes.

ASSEMBLY AND INSTALLATION

All S.R. Smith Rogue

Grand Rapids

are inspected prior to shipment from the

factory. Proper assembly and installation is mandatory. Improper assembly and

installation voids S.R. Smith’s warranty and may affect the safety of the user. S.R.

Smith cannot and does not guarantee customer’s concrete deck.

DRAWINGS

All drawings in this Slide Owner’s Manual (FIGURES I through O) are for illustration

purposes only and are

NOT TO SCALE

MANUFACTURER’S PLACEMENT INSTRUCTIONS

The Rogue

Grand Rapids

owner must confirm that the Installer has followed

the Manufacturer’s Placement Instructions.

1. The critical dimensions for placement of the slide are as shown in FIGURES I and J.

A. The slide exit runway surface shall not exceed twenty inches (20”) above the

water surface and not less than eight inches (8”) above the deck/coping surface

(see Figure I).

B. The slide shall be positioned so that all water flowing off the runway exit drops

into the pool.

C. The minimum depth of water below the exit lip of the slide shall be three feet (3’)

and increases to four feet six inches (4’-6”) at Pt.A, which is a distance of four

feet six inches (4’-6”) from the exit lip of the slide. (see Figure I).

D. A minimum depth of four feet six inches (4’-6”) shall be maintained at a distance

of nine feet (9’) along the extended centerline of the slide from Pt.A. (see

FIGURE I).

2. A minimum clearance area in front of the slide shall be

maintained away from the coping, another slide, a diving

board or a rope and float line. (see FIGURE L)

A. The minimum clearance distance on either side of the

extended centerline of the slide runway shall not be

less than three feet six inches (3’-6”) at a point no

less than two feet six inches (2’-6”) from the exit of

the slide and extending a distance of thirteen feet six

inches (13’-6”) in front of the slide. (see FIGURE J)

B. The minimum clearance area in front of a diving

board is a minimum distance of three feet six inches

(3’-6”) on either side of the board’s centerline. Pt.C

extends a minimum distance of “C” from the tip end of

the board. The width distance “W” on either side of

Pt.C is given in CHART 1 and shown in FIGURE K.

FIGURE I

FIGURE J

“C”

DIMENSION FOR BOARD

= AB + BC

“W”

DIMENSION FOR BOARD

= WIDTH AT PT.C

C. The minimum clearance area of a slide or diving board shall not intersect any

coping or rope and float line. (see FIGURE L) The minimum clearance area of

a slide or diving board may intersect each other provided that they are not used

simultaneously.

CHART 1

BOARD MINIMUM CLEARANCE AREA

POOL TYPE

“C” DIMENSION “W” DIMENSION

I 14’-6” 5’-0”

II 14’-6” 6’-0”

III 16’-6” 6’-0”

IV 18’-6” 7’-6”

V 21’-0” 7’-6”

See Article 5 contained in ANSI/APSP/ICC-5 2011

STANDARD FOR RESIDENTIAL INGROUND SWIMMING

POOLS and refer to Figure 3 and Table 1 for Minimum Water

Envelope Dimensions AB, BC and Width at Point C.

FIGURE L

FIGURE K

INSTALLED SLIDES’ STRUCTURAL & INSTALLATION CHECKLIST

After installation and prior to the first use of the Rogue

Grand Rapids

and

periodically (see DAILY/WEEKLY MAINTENANCE OF THE ROGUE

GRAND

RAPIDS

) thereafter the owner must:

1. Inspect the runway for visible cracks or tears.

2. Inspect the slide for sharp edges, protrusions, cracks or tears.

3. Inspect all attachment flanges for loose or corroded fasteners.

4. Inspect all ladder tread or step-attachment points for evidence of shear, bending

yield, or fatigue in the ladder steps, rails, or attachments means. Yield is

evidenced by crystallization or fine cracking of the ladder tread and/or surface.

5. Inspect the ladder handrails for rigidity and attachment. (Can they be pulled out

of their sockets?)

6. Measure the following dimensions and compare with the Manufacturer’s

Placement Instructions on pages 3 and 4.

•Measure the depth of water in front of the slide exit. (4-1/2’ min. depth 4-

1/2’ from exit end of slide.)

•Measure the height of the slide runway exit above the water. (20” max.)

•Measure the distance between the slide centerline and the edge of other

pool equipment.

7. Observe the position of the exit of the slide as shown in FIGURES J, K and L on

pages 3 and 4.

INTENDED USE INSTRUCTIONS

* * IMPORTANT * *

READ AND FOLLOW THE SIMPLE SAFETY RULES BELOW.

MAKE SURE THAT EVERYONE WHO USES THE ROGUE

GRAND RAPIDS

KNOWS AND FOLLOWS THESE RULES.

ENFORCE THESE RULES WITH ADULT SUPERVISION

Installed and used properly, the Rogue

Grand Rapids

will give you, your family,

friends and guests many hours of enjoyment. Like any other piece of equipment

however, the Rogue

Grand Rapids

can be misused in such a way as to cause the

user injury, even serious and crippling injury. As the owner of a Rogue

Grand

Rapids

it is your responsibility to do the following:

1. Only one person allowed on the slide at any given time.

2. Roughhousing or horseplay on the slide is strictly forbidden.

3. Do not use the slide as a diving platform. The slide is made for sliding only, not

diving.

4. Before sliding, always be sure that the water lubrication is turned on.

5. Familiarize yourself with the shape of the pool bottom and the water depth before

you slide. Use the correct slide configuration shown on the ladder when sliding.

6. Avoid sliding until all submerged obstacles, surface objects or other swimmers

are clear of the slider’s pathway.

7. Don’t slide at or through objects such as inner tubes, as they force the slider

deeper increasing the potential of a crippling injury.

8. Don’t drink alcoholic beverages and slide.

9. Don’t slide alone; use the buddy system.

10.The slide is a deep-water slide and should be installed only according to the

instructions on pages 3 and 4 of this manual. Don’t allow children to use the

slide without adequate supervision. Users must be swimmers.

11.Take your time in preparing to slide. Move forward slowly and get yourself

positioned properly before starting the slide.

12.Handicapped persons should use caution and may require supervision.

13.Do not use the slide if any part of it becomes damaged, weakened, or broken.

Don’t take chances. Have the slide inspected and, if necessary, repaired by a

competent professional, who is familiar with acrylic water slides before using the

RogueGrand Rapids water slide again. See

INSTALLED SLIDES’ STRUCTURAL &

INSTALLATION CHECKLIST

on page 5.

14.Individuals who exhibit frailty due to age should not use the slide.

15.People with history of back problems, heart conditions or fear of heights should

not use the slide.

16.People who weigh over 250 pounds should not use the slide.

17.Women who are pregnant should not use the slide.

18.Don’t use any other sliding technique, other than the following:

SITTING SLIDE POSITION

In sitting slides, face forward on the slide holding the legs and arms straight out with the

palms of your hands tilted upward. (see FIGURE M).

* * IMPORTANT * *

In order for a person to minimize the possibility of injury, HEAD FIRST SLIDES ARE

STRICTLY PROHIBITED. (see FIGURE N below). It is necessary that the user know

that the chief danger of this type of slide is serious spinal injury. Injuries to the spine

may result in temporary or permanent paralysis or even death. Research studies have

shown that you cannot rely on the water to slow you down sufficiently to avoid injury.

FIGURE M

CARELESS MISUSE CAN CAUSE SERIOUS

MINIMUM WATER DEPTH 4 1/2 FEET

SWIMMERS ONLY

NO STANDING OR DIVING FROM THIS SLIDE

DO NOT USE IF PREGNANT

DO NOT USE IF PHYSICALLY IMPAIRED

RESIDENTIAL USE ONLY

SITTING SLIDE

CORRECT

ONLY ONE PERSON AT A TIME

LOOKOUT FOR PEOPLE AND OBJECTS BELOW

WARNING

CAUTION

WARNING

INJURY

IN SEATED POSITION

SLIDE FEET & ARMS FIRST

250 LBS WEIGHT LIMIT

As a Rogue

Grand Rapids

owner, it is your responsibility to explain the nature of

this danger to all persons who may use your Rogue

Grand Rapids

, since they may

not otherwise appreciate the dangers of performing headfirst slides.

DAILY/WEEKLY MAINTENANCE OF THE ROGUE

GRAND RAPIDS

1. When hosing down the deck, hose your Rogue

Grand Rapids

to wash away

any dust, dirt or other debris, which may have accumulated.

2. Be sure that water fittings are not leaking, and clean spray nozzles to permit

water to be sprayed on the slide runway.

3. All anodized aluminum parts require little maintenance. Hose and wipe to clean.

4. While cleaning aluminum parts, check and see that all nuts and bolts are tight

and secure.

5. The

INTENDED USE LABELS

shall be maintained on the ladder and the transom of

the slide entrance as indicated to the right. If they become faded or unreadable

they should be replaced. Additional labels are available from S.R. Smith upon

request. (see FIGURE O).

6. Inspect the runway for visible cracks or tears, sharp edges or protrusions.

7. Inspect all attachment flanges for loose or corroded fasteners.

8. Inspect all ladder tread or step-attachment points for evidence of shear, bending

yield, or fatigue in the ladder steps, rails, or attachments means. Yield is

evidenced by crystallization or fine cracking of the ladder tread and/or surface.

9. Inspect the

ladder handrails

for rigidity and

attachment.

DO NOT SLIDE HEAD FIRST

FIGURE N

FIGURE O

CLEANING INSTRUCTIONS

Use Nonabrasive soap and water when possible. In addition, you may safely use:

Windex

® With Ammonia Formula 409 ® Fantastik ®

Spiffits Bath Scrubfree Tackle ®

Spic and Span ® Powder Calgon ® Bath Topjob ®

Clorox ® Bleach Glass Plus ® Tilex ®

Always read the label instructions on any cleaner carefully before applying it to a

Plexiglas ® DR ® acrylic surface.

AVOID HARSH CHEMICALS AND DISINFECTANTS. DO NOT USE:

Dow with Scrubbing Bubbles ® Lysol ® Disinfectant Ajax ® Cleanser

Windex ® With Vinegar White Cap ® Ajax ® Liquid

White Cap ® Soft Scrub ®

Andere Handbücher für ROGUE GRAND RAPIDS

Inhaltsverzeichnis

Andere S.R.Smith Beleuchtungsausrüstung Handbücher

S.R.Smith

S.R.Smith SlideAway Installationsanleitung

S.R.Smith

S.R.Smith LM10 Bedienungsanleitung

S.R.Smith

S.R.Smith CYCLONE Gebrauchsanweisung

S.R.Smith

S.R.Smith EDGE 6 Programmierhandbuch

S.R.Smith

S.R.Smith PAL Series Bedienungsanleitung

S.R.Smith

S.R.Smith BYOS 2 Programmierhandbuch

S.R.Smith

S.R.Smith heliX2 Gebrauchsanweisung

S.R.Smith

S.R.Smith AQUABLAST Bedienungsanleitung

S.R.Smith

S.R.Smith R Series Bedienungsanleitung

S.R.Smith

S.R.Smith FRONTIER II Bedienungsanleitung

S.R.Smith

S.R.Smith TURBOTWISTER Gebrauchsanweisung

S.R.Smith

S.R.Smith Power Tower PT-6002 Bedienungsanleitung

S.R.Smith

S.R.Smith Star Series Bedienungsanleitung

S.R.Smith

S.R.Smith multiLift 2 Leitfaden

S.R.Smith

S.R.Smith pLX-PL60 Kurzanleitung

S.R.Smith

S.R.Smith PT-6001 Power Tower Bedienungsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith VORTEX Gebrauchsanweisung

S.R.Smith

S.R.Smith 6004 Series Bedienungsanleitung

S.R.Smith

S.R.Smith SWIM CLUB II FUNSLIDE Bedienungsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith TYPHOON Gebrauchsanweisung

S.R.Smith

S.R.Smith SRS-TX-30 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung