S.R.Smith HeliX2 Gebrauchsanweisung

06-755 SEPT19

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

SRS AUSTRALIA, PTY LTD

12 Enterprise St

Richlands QLD 4077

Australia

Phone 07 3812 2283 • Fax 07 3812 1187

www.srsmith.com/au

S.R. SMITH, LLC

CORPORATE HEADQUARTERS

P.O. Box 400 • 1017 S.W. Berg Parkway

Canby, Oregon 97013

USA

Phone (503) 266 2231 • Fax (503) 266 4334

www.srsmith.com

S.R. SMITH HELIX2 SLIDES ARE MANUFACTURED FOR INSTALLATION

AND USE ON RESIDENTIAL INGROUND SWIMMING POOLS ONLY. THE

HELIX2 IS NEVER TO BE INSTALLED AND USED ON ABOVEGROUND

POOLS, ONGROUND POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING

DOCKS OR PLATFORMS OR OTHER BODIES OF WATER SUCH AS

LAKES, PONDS, RIVERS, ETC.

TABLE OF CONTENTS

INTRODUCTION...........................................................................................................................................3

INSTALLED HELIX2 STRUCTURAL & INSTALLATION CHECKLIST ........................................................4

MAINTENANCE INSTRUCTIONS................................................................................................................4

ASSEMBLED HELIX2 LAYOUT ...................................................................................................................5

PARTS LIST..................................................................................................................................................6

ASSEMBLY INSTRUCTIONS.......................................................................................................................7

Tools Required..........................................................................................................................................7

Gasket Installation.....................................................................................................................................7

HELIX2 Assembly .....................................................................................................................................8

ON-DECK MOUNTING INSTRUCTIONS...................................................................................................15

SLIDE PLUMBING INSTRUCTIONS..........................................................................................................16

MANUFACTURER’S PLACEMENT INSTRUCTIONS ...............................................................................17

APPENDIX A.................................................................................................................................................A

APPENDIX B.................................................................................................................................................B

Visit srsmith.com for information on the complete line of

S.R.Smith pool products.

SLIDE ASSEMBLY AND INSTALLATION VIDEOS AVAILABLE AT

www.youtube.com/srsmithllc

www.srsmith.com/en/customer-service/product-registration

INTRODUCTION

DANGER –FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE

OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.

THE HELIX2 SLIDE IS DESIGNED AND MANUFACTURED FOR INSTALLATION AND USE ON

INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THIS SLIDE ON ABOVE GROUND

POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES

OF WATER SUCH AS LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE,

AND SUPERVISION ARE ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE RISK OF

SERIOUS INJURY OR DEATH.

ALL NATIONAL AND LOCAL BUILDING CODES MUST BE FOLLOWED. THIS INCLUDES ANY

APPLIABLE REQUIREMENTS FOR SIZE OF CONCRETE FOOTING, OVERALL HEIGHT OF SLIDE,

AND BODING OR ELECTRICAL CODES.

CHECK INSIDE ALL BOXES AND PACKAGING MATERIALS FOR PARTS. BEFORE BEGINNING

ASSEMBLY, READ ALL INSTRUCTIONS AND IDENTIFY PARTS USING THE FIGURES AND PARTS

LISTED IN THIS DOCUMENT. IT IS CRITICAL THAT ALL PARTS BE CAREFULLY INSPECTED BY

THE INSTALLER PRIOR TO INSTALLATION TO ENSURE THAT NO DAMAGE OCCURRED IN

TRANSIT AND THAT A DAMAGED PART IS NOT USED. PROPER INSTALLATION CANNOT BE

OVERSTRESSED, IMPROPER INSTALLATION VOIDS S.R. SMITH’S WARRANTY AND MAY

AFFECT THE SAFETY OF THE USER.

INSTALLER MUST GIVE TO SLIDE OWNER: HELIX2 INSTALLATION AND OWNER’S MANUAL, THE

WARRANTY CARD, AND ANSWER ALL QUESTIONS REGARDING SAFE AND PROPER USE AND

SLIDE MAINTENANCE.

FOR COMPLETE SLIDE SAFETY INFORMATION REFER TO THE OWNER’S MANUAL.

INSTALLED HELIX2 STRUCTURAL & INSTALLATION CHECKLIST

Installer to review with slide owner upon completion of slide installation.

1. Inspect the runway for visible cracks or tears.

2. Inspect the ladder for sharp edges, protrusions, cracks, or tears.

3. Inspect all fasteners to make sure they are fully tightened.

4. Inspect the ladder for rigidity and attachment.

5. Measure the following dimensions and compare with the manufacturer’s placement instructions on

page 17.

•Pool water depth at the base of the slide should be at least 3’ (0.914 M) deep, and at 4’6”

(1.372 M) out from slide exit, should be at least 4’6” (1.372 M) deep.

•The height of the slide runway exit above the water should be 20” (0.508 M) maximum.

•The distance between the slide centerline and the edge of other pool equipment should be at

least 3’6” (1.067 M).

6. Observe the position of the exit of the slide as shown in FIGURE N, FIGURE O, and FIGURE Q on

pages 17 and 18.

MAINTENANCE INSTRUCTIONS

1. When hosing down the deck, hose your HELIX2 to wash away any dust, dirt or other debris, which

may have accumulated.

2. Be sure that all connections are secure. Tighten hardware if necessary.

3. All polyethylene parts require little maintenance. Hose and wipe to clean.

While cleaning slide, check and see that all nuts and bolts are tight and secure.

4. Inspect the runway for visible cracks or tears, sharp edges and protrusions.

5. Inspect all attachment points for loose or corroded fasteners.

6. Inspect all ladder tread or step-attachment points for evidence of shear, bending yield, or fatigue in

the ladder steps, rails, or attachments means. Yield is evidenced by crystallization or fine cracking of

the ladder tread and/or surface.

7. Inspect the ladder handrails for rigidity and attachment.

ASSEMBLED HELIX2 LAYOUT

FIGURE A

See Appendices A and B for additional slide layout details.

NOT A

PROJECTED

VIEW

(5)

(6)

(7)

(8)

(1)

PARTS LIST

Visit srsmith.com for hardware kit and replacement part information.

Item No.

Part No.

Description

Qty.

5-139

3/8” Hex Nut

9 ea.

5-151

3/8” Lock Washer

11 ea.

05-14-115

1/2" Lock Washer

8 ea.

5-145

3/8” Flat Washer

25 ea.

5-246

3/8” x 2-3/4” Carriage Bolt

2 ea.

5-247

3/8” x 3” Button Head Cap Screw

4 ea.

5-239

3/8” x 2-1/2” Stud

4 ea.

5-259

3/8” x 5” Lag Screw

6 ea.

5-237

3/8” x 5” Button Head Cap Screw

2 ea.

5-248

3/8” x 3.5” Hex Head Cap Screw

2 ea.

5-242

#14" x 1” Pan Head Tapping Screw

6 ea.

5-241

1/2" x 5” Anchor Stud

8 ea.

5-643

3/8”-16 x 2 Hex Head Tap Bolt

1 ea.

05-782

1.5” PVC Pipe Strap

2 ea.

05-767

1” Pipe Clamp

2 ea.

05-770

1” Ball Valve Gray

1 ea.

05-784

1” Coupling

1 ea.

05-773

Garden Hose Adapter

1 ea.

8-532

.5" HIGH X .5” WIDE X 32” LONG RUBBER GASKET

1 ea.

05-643

Dark Gray PVC, 1” Slip Pipe Fitting, Female Tee ,SCH80

1 ea.

05-660

D.G. 1” PVC Slip Reducer to ½” Threaded Female, SCH 80

1 ea.

05-667

3/8” to1/2” barbed 90° elbow fitting

1 ea.

05-786-1

1” PVC Flex Hose, 16” long (Not Shown)

1 ea.

05-786-2

1” PVC Flex Hose, 68” long (Not Shown)

1 ea.

05-661

1” PVC Pipe x 2” Long (Not Shown)

1 ea.

5-156

3/8” Acorn Nut

1 ea.

05-040-2

1/2" OD X 3/8" ID Polypropylene Tubing (23") (Not Shown)

1 ea.

05-642

Valve for .5” OD Tube, Push Fit (Not Shown)

1 ea.

8-545A

Kit, Top Runway Gasket (Not Shown)

1 ea.

(9)

(10)

(16)

(12)

(14)

(11)

(18)

(17)

(2)

(3)

(4)

(13)

(19)

(20)

(21)

(22)

(26)

(15)

ASSEMBLY INSTRUCTIONS

Tools Required

1. Ratchet handle

2. 9/16” deep socket

3. 9/16” wrench

4. 5/8” wrench

5. 3/4" socket or wrench

6. 7/32” allen wrench

7. Phillips head screwdriver

8. 1/2" (13 mm) concrete drill bit

9. 1/4" (6 mm) drill bit

10. Power drill

11. PVC pipe primer & glue

12. Anti-seize

13. Saw to cut PVC pipe

14. Knife

15. Level

16. Teflon tape (plumbers tape)

17. Silicone sealant

18. Pistol-grip clamp (optional)

Gasket Installation

•Most of the gasket material has been installed at the factory, however additional gasket has been

provided in case any gasket has fallen off during shipping. If gasket installation is required, follow

the instructions below. The gasket on the face of the ladder is not installed in the factory, but

detailed instructions are provided in step 8 on page 10.

•Apply gasket (PN 8-532) in the required locations as shown in the figures below.

•Place gasket along the section to determine the length needed.

•Cut gasket to appropriate length, within the width of the runway only, do not include the shoulder.

•Remove backing and adhere gasket to slide.

•All gaskets below are applied as shown in the gasket section detail (see step 8 for further details

on installing the ladder gasket, PN 8-531)

FIGURE B

NOTE:

BE SURE TO APPLY ANTI-SEIZE TO ALL

FASTENERS TO PREVENT GALLING.

NOTE: Use pistol-grip clamps as

necessary to align the molded parts.

HELIX2 Assembly

Before getting started:

•To prevent damage to the parts during assembly, it is recommended that cardboard or some

other protective barrier is laid down on the ground where the slide is to be assembled.

•Verify that the gasket material is affixed to the slide parts as shown on page 7

•During assembly, be sure to apply a thin coat of anti-seize compound to the threads of all

fasteners. Anti-seize helps aid in assembly, prevents galling, and improves corrosion resistance.

1. Attach the pedestal part to the runway exit section as shown in FIGURE C by inserting the two lag

screws into the holes located in the bottom of the pedestal.

2. Before inserting the lag bolts into the side of the runway exit part, 1/4” (6 mm) pilot holes must be

drilled into the center of each of the recesses, each location is marked with a dimple showing where

to drill. The pilot holes should be drilled through both the runway exit section and into the pedestal.

FIGURE C

3. Place the assembled runway exit section and pedestal upright so that the pedestal is resting on the

ground. Notes: It may take more than one person to perform this step. Verify that the gasket

material is properly attached before assembling the parts.

4. Insert the threaded studs into each of the threaded inserts as shown in FIGURE D. The studs should

be screwed in by hand until they reach the bottom of the insert. If the studs cannot be threaded in by

hand, pliers may be used. Before using pliers, a piece of cloth should be placed over the stud to

protect the threads from damage. Note: Be sure to apply anti-seize to all fasteners to prevent

galling.

(8)

5. Assemble the top ladder section and lower ladder section as shown in FIGURE E. Insert the two

button head cap screws into the threaded inserts as shown in FIGURE E. Do not fully tighten the

screws at this point; start the screws into the threaded inserts. Note: Be sure to apply anti-

seize to all fasteners to prevent galling.

6. Insert the button head cap screws into the back side of the ladder as shown in FIGURE F. Tighten

the screws until snug. Go back and fully tighten the screws from Step 5. Note: Be sure to apply

anti-seize to all fasteners to prevent galling.

7. Insert the two carriage bolts into the steps as shown in FIGURE E. Tighten the nuts onto the

carriage bolt until the lock washer is fully compressed. Note: Be sure to apply anti-seize to all

fasteners to prevent galling

FIGURE D

FIGURE E

(2)

(1)

(4)

(6)

(4)

(5)

8. Before applying the gasket to the top of the ladder, be sure that the joint surfaces of the top runway

and ladder sections are clean and dry. Unroll the gasket material and hold so that length of the gasket

is centered on the center of the ladder joint. With the exposed adhesive side of the gasket facing the

ladder joint surface, apply the gasket starting at the center of the part, working outward to the sides.

Be sure that the bottom edge of the gasket material is held against the shelf on the ladder part during

installation, see reference images below. Do not make too tight of a bend radius with the gasket when

transitioning the gasket up the vertical edges of the joint. The transition radius should be as large as

possible. Making too tight of a bend radius will cause the gasket to kink and possibly leak. The

gasket should be centered on the available space in the vertical area of the joint, see reference

images below. Once the gasket is in place, firmly press down on the gasket in all locations to ensure

that the gasket has completely adhered to the ladder joint surface. Remove the paper backing on the

outward face of the gasket to expose the adhesive. Use caution not to remove the adhesive strip

from the gasket when removing the paper backing.

GASKET

FIGURE F

Inhaltsverzeichnis

Andere S.R.Smith Beleuchtungsausrüstung Handbücher

S.R.Smith

S.R.Smith Power Tower PT-6002 Bedienungsanleitung

S.R.Smith

S.R.Smith ROGUE GRAND RAPIDS Bedienungsanleitung

S.R.Smith

S.R.Smith 6004 Series Bedienungsanleitung

S.R.Smith

S.R.Smith CYCLONE Gebrauchsanweisung

S.R.Smith

S.R.Smith pLX-PL60 Kurzanleitung

S.R.Smith

S.R.Smith R Series Bedienungsanleitung

S.R.Smith

S.R.Smith PT-6001 Power Tower Bedienungsanleitung

S.R.Smith

S.R.Smith SRS-TX-30 Bedienungsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith LM10 Bedienungsanleitung

S.R.Smith

S.R.Smith SWIM CLUB II FUNSLIDE Bedienungsanleitung

S.R.Smith

S.R.Smith TYPHOON Gebrauchsanweisung

S.R.Smith

S.R.Smith FRONTIER II Bedienungsanleitung

S.R.Smith

S.R.Smith AQUABLAST Bedienungsanleitung

S.R.Smith

S.R.Smith Star Series Bedienungsanleitung

S.R.Smith

S.R.Smith SlideAway Installationsanleitung

S.R.Smith

S.R.Smith BYOS 2 Programmierhandbuch

S.R.Smith

S.R.Smith multiLift 2 Leitfaden

S.R.Smith

S.R.Smith TURBOTWISTER Gebrauchsanweisung

S.R.Smith

S.R.Smith PAL Series Bedienungsanleitung

S.R.Smith

S.R.Smith VORTEX Gebrauchsanweisung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith EDGE 6 Programmierhandbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung

S.R.Smith heliX2 Gebrauchsanweisung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken