S.R.Smith TURBOTWISTER Gebrauchsanweisung

06-693 June16

TURBOTWISTER®

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

SRS AUSTRALIA, PTY LTD

12 Enterprise St

Richlands QLD 4077

Australia

Phone 07 3812 2283 • Fax 07 3812 1187

www.srsmith.com/au

S.R. SMITH, LLC

CORPORATE HEADQUARTERS

P.O. Box 400 • 1017 S.W. Berg Parkway

Canby, Oregon 97013

USA

Phone (503) 266 2231 • Fax (503) 266 4334

www.srsmith.com

S.R. SMITH TURBOTWISTER SLIDES ARE MANUFACTURED FOR

INSTALLATION AND USE ON RESIDENTIAL INGROUND SWIMMING

POOLS ONLY. THE TURBOTWISTER IS NEVER TO BE INSTALLED AND

USED ON ABOVEGROUND POOLS, ONGROUND POOLS, HOUSEBOATS,

BOAT DOCKS, FLOATING DOCKS OR PLATFORMS OR OTHER BODIES

OF WATER SUCH AS LAKES, PONDS, RIVERS, ETC.

TABLE OF CONTENTS

INTRODUCTION...........................................................................................................................................3

INSTALLED TURBOTWISTER STRUCTURAL & INSTALLATION CHECKLIST........................................4

MAINTENANCE INSTRUCTIONS................................................................................................................4

ASSEMBLED TURBOTWISTER LAYOUT...................................................................................................5

ASSEMBLY INSTRUCTIONS.......................................................................................................................6

Tools Required..........................................................................................................................................6

Gasket Installation.....................................................................................................................................6

MAIN SECTION PARTS LIST.......................................................................................................................7

MAIN SECTION ASSEMBLY........................................................................................................................8

CONCRETE WEDGE ANCHOR MOUNTING INSTRUCTIONS................................................................16

WATER SYSTEM PARTS LIST..................................................................................................................18

WATER SYSTEM ASSEMBLY..................................................................................................................19

MANUFACTURER’S PLACEMENT INSTRUCTIONS ...............................................................................22

Visit srsmith.com for information on the complete line of

S.R.Smith pool products.

SLIDE ASSEMBLY AND INSTALLATION VIDEOS AVAILABLE AT

www.youtube.com/srsmithllc

www.srsmith.com/en/customer-service/product-registration

INTRODUCTION

DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE

OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.

TURBOTWISTER IS DESIGNED AND MANUFACTURED FOR INSTALLATION AND USE ON

INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THIS SLIDE ON ABOVE GROUND

POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES

OF WATER SUCH AS LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE,

AND SUPERVISION ARE ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE RISK OF

SERIOUS INJURY OR DEATH.

ALL NATIONAL AND LOCAL BUILDING CODES MUST BE FOLLOWED. THIS INCLUDES ANY

APPLICABLE REQUIREMENTS FOR SIZE OF CONCRETE FOOTING, OVERALL HEIGHT OF SLIDE,

AND BODING OR ELECTRICAL CODES.

CHECK INSIDE ALL BOXES AND PACKAGING MATERIALS FOR PARTS. BEFORE BEGINNING

ASSEMBLY, READ ALL INSTRUCTIONS AND IDENTIFY PARTS USING THE FIGURES AND PARTS

LISTED IN THIS DOCUMENT. IT IS CRITICAL THAT ALL PARTS BE CAREFULLY INSPECTED BY

THE INSTALLER PRIOR TO INSTALLATION TO ENSURE THAT NO DAMAGE OCCURRED IN

TRANSIT AND THAT A DAMAGED PART IS NOT USED. PROPER INSTALLATION CANNOT BE

OVERSTRESSED, IMPROPER INSTALLATION VOIDS S.R. SMITH’S WARRANTY AND MAY

AFFECT THE SAFETY OF THE USER.

INSTALLER MUST GIVE TO SLIDE OWNER: TURBOTWISTER INSTALLATION AND OWNER’S

MANUAL, THE WARRANTY CARD, AND ANSWER ALL QUESTIONS REGARDING SAFE AND

PROPER USE AND SLIDE MAINTENANCE.

FOR COMPLETE SLIDE SAFETY INFORMATION REFER TO THE OWNER’S MANUAL.

INSTALLED TURBOTWISTER STRUCTURAL & INSTALLATION CHECKLIST

Installer to review with slide owner upon completion of slide installation.

1. Inspect the runway for visible cracks or tears.

2. Inspect the ladder for sharp edges, protrusions, cracks, or tears.

3. Inspect all fasteners to make sure they are fully tightened.

4. Inspect the ladder for rigidity and attachment.

5. Measure the following dimensions and compare with the manufacturer’s placement instructions on

pages 22-23.

•Pool water depth at the base of the slide should be at least 3’-0” (0.914 M) deep, and at 4’-6”

(1.372 M) out from slide exit, should be at least 4’-6” (1.372 M) deep.

•The height of the slide runway exit above the water should be 20” (0.508 M) maximum.

•The distance between the slide centerline and the edge of other pool equipment should be at

least 3’-6” (1.067 M).

6. Observe the position of the exit of the slide as shown in Figure W, Figure X, and Figure Z, on pages

22 and 23.

MAINTENANCE INSTRUCTIONS

1. When hosing down the deck, hose your TurboTwister to wash away any dust, dirt or other debris that

may have accumulated.

2. Be sure that all connections are secure. Tighten hardware if necessary.

3. All polyethylene parts require little maintenance. Hose and wipe to clean.

While cleaning slide, check and see that all nuts and bolts are tight and secure.

4. Inspect the runway for visible cracks or tears, sharp edges and protrusions.

5. Inspect all attachment points for loose or corroded fasteners.

6. Inspect all ladder tread or step-attachment points for evidence of shear, bending yield, or fatigue in

the ladder steps, rails, or attachment means. Yield is evidenced by crystallization or fine cracking of

the ladder tread and/or surface.

7. Inspect the ladder handrails for rigidity and attachment.

ASSEMBLED TURBOTWISTER LAYOUT

The left curve TurboTwister is shown for illustration.

The right curve TurboTwister is a mirror image of the left.

Figure A

ASSEMBLY INSTRUCTIONS

Tools Required

1. Ratchet handle

2. 9/16” deep socket

3. 9/16” wrench

4. 3/4" socket or wrench

5. 7/32” Allen wrench

6. Phillips head screwdriver

7. 1/2"Ø (12.7 mm) concrete drill bit

8. 1/4"Ø (6.3 mm) drill bit

9. Power drill

10. PVC pipe primer & glue

11. Anti-seize

12. Saw to cut PVC pipe

13. Knife

14. Level

Gasket Installation

•Most of the gasket material has been installed at the factory, however additional gasket has been

provided in case any gasket has fallen off during shipping. If gasket installation is required, follow

the instructions below in Figure B. The gasket on the face of the ladder is not installed in the

factory, but detailed instructions are provided on page 12, Figure K.

•Apply gasket in the required locations as shown in Figure B.

•Place gasket along the section to determine the length needed.

•Cut gasket to appropriate length.

•Remove backing and adhere gasket to slide.

•All gaskets below are applied as shown in Figure B in the Joint / Gasket Cross-Section Detail.

•See page 12, Figure K, for further details on installing the ladder gasket, PN 8-531.

Figure B

MAIN SECTION PARTS LIST

Visit srsmith.com for hardware kit and replacement part information.

ITEM NO.

PART NO.

DESCRIPTION

QTY.

KIT A

KIT A 69-209-168 TUROBOTWISTER HARDWARE CARTON 1 ea.

1 5-139 3/8” HEX NUT 14 ea. ●

2 5-151 3/8” LOCK WASHER 14 ea. ●

3 05-14-115 1/2" LOCK WASHER 8 ea. ●

4 5-145 3/8” FLAT WASHER 35 ea. ●

5 5-235 3/8” x 2-1/4” CARRIAGE BOLT 2 ea. ●

6 5-236 3/8” x 2-1/4” BUTTON HEAD CAP SCREW 2 ea. ●

7 5-249 3/8” x 3-1/4” BUTTON HEAD CAP SCREW 2 ea. ●

8 5-239 3/8” x 2-1/2” STUD 4 ea. ●

9 5-240 3/8” x 3-1/2” LAG SCREW 9 ea. ●

10 5-237 3/8” x 5” BUTTON HEAD CAP SCREW 4 ea. ●

11 5-238 3/8” x 6” HEX HEAD CAP SCREW 4 ea. ●

12 5-241 1/2" x 5” CONCRETE WEDGE ANCHOR WITH HARDWARE 8 ea. ●

13 8-532 1/2" HIGH x 1/2” WIDE x 32” LONG RUBBER GASKET (NOT SHOWN) 1 ea.

14 8-531 TOP RUNWAY GASKET KIT (NOT SHOWN) 1 ea.

MAIN SECTION ASSEMBLY

1. Place the Pedestal on the ground and set the Exit Slide Section on top as shown in Figure C.

2. Attach the Exit Slide Section to the Middle Slide Section as shown in Figure D.

If necessary lift up on the end of the exit runway in order to keep the joint tight while fastening.

Note: Ensure gasket material at the joint is intact before assembling.

The required hardware is as follows: 3/8” x 5” Socket Head Cap Screw (10), 3/8” Flat Washer (4), 3/8”

Flat Washer (4), 3/8” Lock Washer (2), 3/8” Hex Nut (1).

Note: When assembling the slide, apply a thin even coating of anti-seize to all stainless steel

fasteners. Anti-Seize aids in assembly, prevents galling, and improves corrosion resistance.

Anti-Seize can be purchased at most auto parts stores.

Figure D

Figure C

3. Once the sidewall connections have been made, remove the assembled Exit and Middle Slide

Sections from the Pedestal. Turn the assembly upside down and fasten the underside as shown in

Figure E. The required hardware is as follows: 3/8” x 6” Hex Head Cap Screw (11), 3/8” Flat Washer

(4), 3/8” Flat Washer (4), 3/8” Lock Washer (2), and 3/8” Hex Nut (1).

4. Attach the Pedestal to the Middle Runway Section and Exit Slide Sections. Install the fasteners, as

shown in Figure F. The required hardware is as follows: 3/8” x 3-1/2” Lag Screw (9), and 3/8” Flat

Washer (4).

Figure F

Figure

5. Install four 3/8” x 2-1/2” Studs (8) into the threaded inserts located at the top of the ladder as shown in

Figure G.

6. Assemble the Top and Bottom Ladder Sections as shown in Figure H, Figure I, and Figure J. Do not

fully tighten fasteners until all the hardware is in place. The hardware required for the connections

shown in Figure H are as follows: 3/8” x 2-1/4” Button Head Cap Screw (6) and 3/8” Flat Washer (4).

Figure G

Figure H

Andere Handbücher für TURBOTWISTER

Inhaltsverzeichnis

Andere S.R.Smith Beleuchtungsausrüstung Handbücher

S.R.Smith

S.R.Smith PAL Series Bedienungsanleitung

S.R.Smith

S.R.Smith SWIM CLUB II FUNSLIDE Bedienungsanleitung

S.R.Smith

S.R.Smith EDGE 6 Programmierhandbuch

S.R.Smith

S.R.Smith PT-6001 Power Tower Bedienungsanleitung

S.R.Smith

S.R.Smith LM10 Bedienungsanleitung

S.R.Smith

S.R.Smith TYPHOON Gebrauchsanweisung

S.R.Smith

S.R.Smith AQUABLAST Bedienungsanleitung

S.R.Smith

S.R.Smith Power Tower PT-6002 Bedienungsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith R Series Bedienungsanleitung

S.R.Smith

S.R.Smith heliX2 Gebrauchsanweisung

S.R.Smith

S.R.Smith VORTEX Gebrauchsanweisung

S.R.Smith

S.R.Smith ROGUE GRAND RAPIDS Bedienungsanleitung

S.R.Smith

S.R.Smith FRONTIER II Bedienungsanleitung

S.R.Smith

S.R.Smith Star Series Bedienungsanleitung

S.R.Smith

S.R.Smith 6004 Series Bedienungsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith SlideAway Installationsanleitung

S.R.Smith

S.R.Smith CYCLONE Gebrauchsanweisung

S.R.Smith

S.R.Smith SRS-TX-30 Bedienungsanleitung

S.R.Smith

S.R.Smith pLX-PL60 Kurzanleitung

S.R.Smith

S.R.Smith multiLift 2 Leitfaden

S.R.Smith

S.R.Smith BYOS 2 Programmierhandbuch

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung