S.R.Smith TYPHOON Gebrauchsanweisung

06-714 DEC18

TYPHOON®

ASSEMBLY AND INSTALLATION

INSTRUCTIONS

SRS AUSTRALIA, PTY LTD

12 Enterprise St

Richlands QLD 4077

Australia

Phone 07 3812 2283 • Fax 07 3812 1187

www.srsmith.com/au

S.R. SMITH, LLC

CORPORATE HEADQUARTERS

P.O. Box 400 • 1017 S.W. Berg Parkway

Canby, Oregon 97013

USA

Phone (503) 266 2231 • Fax (503) 266 4334

www.srsmith.com

S.R. SMITH TYPHOON SLIDES ARE MANUFACTURED FOR

INSTALLATION AND USE ON RESIDENTIAL INGROUND SWIMMING

POOLS ONLY. THE TYPHOON IS NEVER TO BE INSTALLED AND USED

ON ABOVEGROUND POOLS, ONGROUND POOLS, HOUSEBOATS, BOAT

DOCKS, FLOATING DOCKS OR PLATFORMS OR OTHER BODIES OF

WATER SUCH AS LAKES, PONDS, RIVERS, ETC.

TABLE OF CONTENTS

INTRODUCTION...........................................................................................................................................3

INSTALLED TYPHOON STRUCTURAL & INSTALLATION CHECKLIST...................................................4

MAINTENANCE INSTRUCTIONS................................................................................................................4

ASSEMBLED TYPHOON LAYOUT..............................................................................................................5

PARTS LIST..................................................................................................................................................6

ASSEMBLY INSTRUCTIONS.......................................................................................................................7

Tools Required..........................................................................................................................................7

Gasket Installation.....................................................................................................................................7

Typhoon Assembly....................................................................................................................................9

ON-DECK MOUNTING INSTRUCTIONS...................................................................................................14

SLIDE PLUMBING INSTRUCTIONS..........................................................................................................15

MANUFACTURER’S PLACEMENT INSTRUCTIONS ...............................................................................16

Visit srsmith.com for information on the complete line of

S.R.Smith pool products.

SLIDE ASSEMBLY AND INSTALLATION VIDEOS AVAILABLE AT

www.youtube.com/srsmithllc

www.srsmith.com/en/customer-service/product-registration

INTRODUCTION

DANGER –FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE

OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.

THE TYPHOON IS DESIGNED AND MANUFACTURED FOR INSTALLATION AND USE ON

INGROUND SWIMMING POOLS ONLY. DO NOT INSTALL THIS SLIDE ON ABOVE GROUND

POOLS, HOUSEBOATS, BOAT DOCKS, FLOATING DOCKS OR PLATFORMS, OR OTHER BODIES

OF WATER SUCH AS LAKES, PONDS, RIVERS, ETC. PROPER ASSEMBLY, INSTALLATION, USE,

AND SUPERVISION ARE ESSENTIAL FOR PROPER OPERATION AND TO REDUCE THE RISK OF

SERIOUS INJURY OR DEATH.

ALL NATIONAL AND LOCAL BUILDING CODES MUST BE FOLLOWED. THIS INCLUDES ANY

APPLIABLE REQUIREMENTS FOR SIZE OF CONCRETE FOOTING, OVERALL HEIGHT OF SLIDE,

AND BODING OR ELECTRICAL CODES.

CHECK INSIDE ALL BOXES AND PACKAGING MATERIALS FOR PARTS. BEFORE BEGINNING

ASSEMBLY, READ ALL INSTRUCTIONS AND IDENTIFY PARTS USING THE FIGURES AND PARTS

LISTED IN THIS DOCUMENT. IT IS CRITICAL THAT ALL PARTS BE CAREFULLY INSPECTED BY

THE INSTALLER PRIOR TO INSTALLATION TO ENSURE THAT NO DAMAGE OCCURRED IN

TRANSIT AND THAT A DAMAGED PART IS NOT USED. PROPER INSTALLATION CANNOT BE

OVERSTRESSED, IMPROPER INSTALLATION VOIDS S.R. SMITH’S WARRANTY AND MAY

AFFECT THE SAFETY OF THE USER.

INSTALLER MUST GIVE TO SLIDE OWNER: TYPHOON SLIDE INSTALLATION AND OWNER’S

MANUAL, THE WARRANTY CARD, AND ANSWER ALL QUESTIONS REGARDING SAFE AND

PROPER USE AND SLIDE MAINTENANCE.

FOR COMPLETE SLIDE SAFETY INFORMATION REFER TO THE OWNER’S MANUAL.

INSTALLED TYPHOON STRUCTURAL & INSTALLATION CHECKLIST

Installer to review with slide owner upon completion of slide installation.

1. Inspect the runway for visible cracks or tears.

2. Inspect the ladder for sharp edges, protrusions, cracks, or tears.

3. Inspect all fasteners to make sure they are fully tightened.

4. Inspect the ladder for rigidity and attachment.

5. Measure the following dimensions and compare with the manufacturer’s placement instructions on

page 16.

•Pool water depth at the base of the slide should be at least 3’ (914 mm) deep, and at 4’6”

(1372 mm) out from slide exit, should be at least 4’6” (1372 mm) deep.

•The height of the slide runway exit above the water should be 20” (508 mm) maximum.

•The distance between the slide centerline and the edge of other pool equipment should be at

least 3’6” (1067 mm).

6. Observe the position of the exit of the slide as shown in FIGURE M, FIGURE N, and FIGURE P on

pages 16 and 17.

MAINTENANCE INSTRUCTIONS

1. When hosing down the deck, hose your Typhoon to wash away any dust, dirt or other debris, which

may have accumulated.

2. Be sure that all connections are secure. Tighten hardware if necessary.

3. All polyethylene parts require little maintenance. Hose and wipe to clean.

While cleaning slide, check and see that all nuts and bolts are tight and secure.

4. Inspect the runway for visible cracks or tears, sharp edges and protrusions.

5. Inspect all attachment points for loose or corroded fasteners.

6. Inspect all ladder tread or step-attachment points for evidence of shear, bending yield, or fatigue in

the ladder steps, rails, or attachments means. Yield is evidenced by crystallization or fine cracking of

the ladder tread and/or surface.

7. Inspect the ladder handrails for rigidity and attachment.

ASSEMBLED TYPHOON LAYOUT

FIGURE A

PARTS LIST

Visit srsmith.com for hardware kit and replacement part information.

ITEM NO.

PART NO.

DESCRIPTION

QTY.

KIT A

69-209-123

TYPHOON HARDWARE CARTON

1 ea.

5-139

3/8” HEX NUT

10 ea.

●

5-151

3/8” LOCK WASHER

10 ea.

●

05-14-115

1/2" LOCK WASHER

8 ea.

●

5-145

3/8” FLAT WASHER

24 ea.

●

5-246

3/8” x 2-3/4” CARRIAGE BOLT

2 ea.

●

5-247

3/8” x 3” BUTTON HEAD CAP SCREW

4 ea.

●

5-239

3/8” x 2-1/2” STUD

4 ea.

●

5-240

3/8” x 3-1/2” LAG SCREW

6 ea.

●

5-237

3/8” x 5” BUTTON HEAD CAP SCREW

2 ea.

●

5-248

3/8” x 3.5” HEX HEAD CAP SCREW

2 ea.

●

5-242

#14" x 1” PAN HEAD TAPPING SCREW

6 ea.

●

5-241

1/2" x 5” ANCHOR STUD

8 ea.

●

05-782

1-1/2” PVC PIPE STRAP

2 ea.

●

05-767

1” PIPE CLAMP

2 ea.

●

05-770

1” BALL VALVE GRAY

1 ea.

●

05-784

1” COUPLING

1 ea.

●

05-773

GARDEN HOSE ADAPTER

1 ea.

●

8-532

1/2" HIGH x 1/2” WIDE x 32” LONG RUBBER GASKET

1 ea.

●

8-545A

KIT, TOP RUNWAY GASKET

1 ea.

●

05-786-1

1” PVC FLEX HOSE, 16” LONG (NOT SHOWN)

1 ea.

05-786-2

1” PVC FLEX HOSE, 68” LONG (NOT SHOWN)

1 ea.

(1)

(2)

(3)

(5)

(6)

(7)

(8)

(9)

(10)

(12)

(15)

(13)

(4)

(11)

(17)

(16)

(18)

(19)

(14)

ASSEMBLY INSTRUCTIONS

Tools Required

1. Ratchet handle

2. 9/16” deep socket

3. 9/16” wrench

4. 3/4" socket or wrench

5. 7/32” allen wrench

6. Phillips head screwdriver

7. 1/2" (13 mm) concrete drill bit

8. 1/4" (6 mm) drill bit

9. Power drill

10. PVC pipe primer & glue

11. Anti-seize

12. Saw to cut PVC pipe

13. Knife

14. Level

15. Pistol-grip clamp (optional)

Gasket Installation

•Most of the gasket material has been installed at the factory, however additional gasket has been

provided in case any gasket has fallen off during shipping. If gasket installation is required, follow

the instructions below. The gasket on the face of the ladder is not installed in the factory, but

detailed instructions are provided in step 8 on page 11.

•Apply gasket (PN 8-532) in the required locations as shown in the figures below.

•Place gasket along the section to determine the length needed.

•Cut gasket to appropriate length.

•Remove backing and adhere gasket to slide.

•All gaskets below are applied as shown in the gasket section detail (see step 8 for further details

on installing the ladder gasket, PN 8-531)

FIGURE B

NOTE:

BE SURE TO APPLY ANTI-SEIZE TO ALL

FASTENERS TO PREVENT GALLING.

NOTE: Use pistol-grip clamps as

necessary to align the molded parts.

Typhoon Assembly

Before getting started:

•To prevent damage to the parts during assembly, it is recommended that cardboard or

some other protective barrier is laid down on the ground where the slide is to be

assembled.

•Verify that the gasket material is affixed to the slide parts as shown on page 6

•During assembly, be sure to apply a thin coat of anti-seize compound to the threads of all

fasteners. Anti-seize helps aid in assembly, prevents galling, and improves corrosion

resistance.

1. Assemble the pedestal part to the runway exit section as shown in FIGURE C. Attach the

pedestal part to the runway exit section by inserting the two lag screws into the holes located in

the bottom of the pedestal.

2. Before inserting the lag bolts into the side of the runway exit part, 1/4” (6 mm) pilot holes must be

drilled into the center of each of the recesses. The pilot holes should be drilled through both the

runway exit section and into the pedestal.

3. Place the assembled runway exit section and pedestal upright so that the pedestal is resting on

the ground.

(8)

(4)

FIGURE C

Notes: It may take more than one person to perform this step. Verify that the gasket material

is properly attached before assembling the parts.

4. Insert the threaded studs into each of the threaded inserts as shown in FIGURE D. The studs

should be screwed in by hand until they reach the bottom of the insert. If the studs cannot be

threaded in by hand, pliers may be used. Before using pliers, a piece of cloth should be placed

over the stud to protect the threads from damage. .

5. Assemble the top ladder section to the lower ladder section as shown in FIGURE E. Insert the

two button head cap screws into the threaded inserts as shown in FIGURE E. Do not fully

tighten the screws at this point; just get the screws started into the threaded inserts.

6. Insert the button head cap screws into the back side of the ladder as shown in FIGURE F.

Tighten the screws until snug. Go back and fully tighten the screws from Step 7.

7. Insert the two carriage bolts into the steps as shown in FIGURE E. Tighten the nuts onto the

carriage bolt until the lock washer is fully compressed.

(7)

FIGURE D

(1)

(2)

(4)

(6)

(4)

(5)

FIGURE E

Andere Handbücher für TYPHOON

Inhaltsverzeichnis

Andere S.R.Smith Beleuchtungsausrüstung Handbücher

S.R.Smith

S.R.Smith Power Tower PT-6002 Bedienungsanleitung

S.R.Smith

S.R.Smith PAL Series Bedienungsanleitung

S.R.Smith

S.R.Smith R Series Bedienungsanleitung

S.R.Smith

S.R.Smith LM10 Bedienungsanleitung

S.R.Smith

S.R.Smith SlideAway Installationsanleitung

S.R.Smith

S.R.Smith AQUABLAST Bedienungsanleitung

S.R.Smith

S.R.Smith Star Series Bedienungsanleitung

S.R.Smith

S.R.Smith PT-6001 Power Tower Bedienungsanleitung

S.R.Smith

S.R.Smith heliX2 Gebrauchsanweisung

S.R.Smith

S.R.Smith multiLift 2 Leitfaden

S.R.Smith

S.R.Smith FRONTIER II Bedienungsanleitung

S.R.Smith

S.R.Smith SRS-TX-30 Bedienungsanleitung

S.R.Smith

S.R.Smith CYCLONE Gebrauchsanweisung

S.R.Smith

S.R.Smith SWIM CLUB II FUNSLIDE Bedienungsanleitung

S.R.Smith

S.R.Smith EDGE 6 Programmierhandbuch

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith rogue2 Bedienungsanleitung

S.R.Smith

S.R.Smith BYOS 2 Programmierhandbuch

S.R.Smith

S.R.Smith TURBOTWISTER Gebrauchsanweisung

S.R.Smith

S.R.Smith VORTEX Gebrauchsanweisung

S.R.Smith

S.R.Smith ROGUE GRAND RAPIDS Bedienungsanleitung

S.R.Smith

S.R.Smith pLX-PL60 Kurzanleitung

S.R.Smith

S.R.Smith 6004 Series Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung