Sper scientific 860032 Bedienungsanleitung

Bench-Top Meters

860031, 860032 and 860033

Instruction Manual

TABLE OF CONTENTS

INTRODUCTION....................................................................................4

FEATURES.............................................................................................4

POWER SUPPLY ...................................................................................5

METER COMPONENTS ........................................................................5

LCD DISPLAY ........................................................................................8

KEYPAD .................................................................................................9

REAR PANEL .......................................................................................10

SETUP MODE.................................................................................11-22

Memory Transmission .......................................................................11

Clear Memory....................................................................................12

View Slope & O󰀨set (pH Probe)........................................................13

Calibration Review (Conductivity Probe)...........................................15

pH Calibration Bu󰀨er (pH Probe) ......................................................16

Select Bu󰀨er......................................................................................16

Cell Constant (Conductivity Probe) ...................................................17

Temperature Setting (Conductivity Probe) ........................................18

Ready Icon ........................................................................................20

Temperature Units.............................................................................20

Real Time Clock Setting....................................................................21

Reset.................................................................................................22

PH PROBE CALIBRATION ..................................................................23

CONDUCTIVITY PROBE CALIBRATION ............................................25

TDS CALIBRATION..............................................................................28

SALINITY CALIBRATION.....................................................................28

MEASUREMENT PROCEDURES ................................................. 29-38

Preparing for Measurement ..............................................................29

Hold Function ....................................................................................29

pH Measurement...............................................................................30

mV Measurement (± 499 mV) ..........................................................31

ORP (mV) Measurement (± 1999 mV)..............................................32

Conductivity Measurement................................................................32

Total Dissolved Solid Measurement .................................................33

Salinity Measurement........................................................................34

Automatic Temperature Compensation .............................................35

Manual Temperature Compensation .................................................35

Auto and Manual Range ...................................................................36

Record Memory.................................................................................37

Recall Memory ..................................................................................37

Recall Maximum & Minimum.............................................................38

MAINTENANCE ...................................................................................39

TROUBLESHOOTING .........................................................................42

ERROR CODES...................................................................................43

PC CONNECTION ...............................................................................44

APPENDICES ......................................................................................47

OPTIONAL ACCESSORIES.................................................................51

SPECIFICATIONS................................................................................52

WARRANTY .........................................................................................56

Bench-Top Meters 860031, 860032, 860033

The contents of this manual may not be reproduced or transmitted in any

form or by any means electronic, mechanical, or other means that do not

yet exist or may be developed, including photocopying, recording, or any

information storage and retrieval system without the express permission

from Sper Scientic.

INTRODUCTION

Sper Scientic is pleased to o󰀨er the following line of bench-top meters:

Model 860031 (pH/mV)

Model 860032 (Conductivity/TDS/Salinity)

Model 860033 (Water Quality)

Please note that the meter itself is identical in each of the above models.

Each model can be used for pH/mV, Conductivity/TDS/Salinity or Water

Quality depending on the probe used.

To utilize your meter under additional parameters, please refer to the list

of probes in OPTIONAL ACCESSORIES on page 51.

Instructions for all three models are contained within this manual. Refer

to the TABLE OF CONTENTS for the subsection within MEASUREMENT

PROCEDURES that corresponds to the particular parameter you are

measuring.

FEATURES

• Multi-display LCD screen

• N.I.S.T. bu󰀨er recognition

• Hold function

• Maximum and minimum

• Reliable, replaceable probe with temperature compensation

• Easy to view probe calibration data

• “Ready” icon on LCD display indicates stability for reading

• PC connection for online logging and uploading 99 memories for analysis

• Automatic or manual temperature compensation

• Analog output for chart recorders

POWER SUPPLY

The meter is powered by a 9 Volt DC adapter (included). The plug of the

adaptor is USA type; you will need to purchase a plug converter if using

the meter outside of the US.

Plug the adaptor into the power port labeled “DC,” located on the rear of

the meter.

METER COMPONENTS

Meter Drawer

A built-in drawer is located on the bottom of the bench-top meter. Pull the

drawer out and use to store notes and other important reference data.

METER COMPONENTS

Probe Holder

The probe holder is composed of two parts: the base and arm. Holder

assembly does not require tools. The maximum swing angle is 70° and

the maximum height of the holder is 378 mm.

Holder Assembly

Holder Disassembly

1. Turn the base upside down.

2. Use a cylindrical object with an approximate 12 mm diameter to push

the arm out of the base.

To disassemble the holder from the base:

METER COMPONENTS

Attaching Holder to the Meter

After assembling the holder, attach the holder to the meter.

1. Find the two holes on the bottom of the meter that are used to hold

the base.

2. The holder can be attached to the right or left side of the meter

Locate the two holes at the

bottom of the meter.

The cylindrical knob

on the holder base is

designed to t into the

hole on the bottom of

the meter.

The holder can hold up to 4

probes. The wire of the probe

can be xed to the arm.

Turn clockwise to lock the holder

into place. Turn counterclockwise

to adjust the holder up and down.

LCD DISPLAY

Primary Data Screen displays pH, mV, ORP, Conductivity, TDS or

Salinity value.

Icons CON, TDS, SALT, ORP, pH, mV indicate the parameter displayed.

Icons ppt, ppm, mg/l, mS, µS, kPA, or mmHg indicate the unit of

measure displayed.

READY indicates the reading is stable.

AUTO indicates auto-ranging function.

MAX, MIN indicate a maximum or minimum memory value.

HLD Holds the current reading on the display.

REC indicates the meter is in recall mode.

MEM indicates the current measured value is saved.

The digital number under MEM indicates the total number of saved records.

The are real time Y-M-D (Year-Month-Date) or H:M:S (Hour-

Minute-Second).

ATC indicates the meter is in Automatic Temperature Compensation Mode.

The temperature display is indicated at the bottom of the LCD.

Temperature unit °C or °F is selectable.

KEYPAD

POWER/SET Press to turn the meter on/o󰀨. Press and

hold for more than 1 second to enter SET

Mode. The meter will default to the last mode

used when turned o󰀨 and back on.

CAL/ESC Switch between NORMAL and

CALIBRATION Mode. Press to enter

manual temperature setting. In Calibration,

Setting or Recall Modes, press to return to

Normal Mode.

HLD/REC Press to freeze the reading. Press again to

release. Press for more than 1 second to

switch between NORMAL and

RECALL Modes.

MODE/▲ Press to switch the mode.

Press to increase the setting value.

MEMO/▼ Press to save the current reading.

Press to decrease the setting value.

MN/MX/

CONFIRM

Press to conrm calibration or parameter

setting. Press to view the min/max of the

memory in Recall Mode. Press to select

AUTO or Manual ranging when in

Cond./TDS/SALT.

REAR PANEL

The bench-top meter provides a complete set of input connectors for

various commonly-used accessories:

Connection Function

DC Connection of the AC to DC adaptor power supply

RS232 Connection of a RS232 or USB cable to a computer

to capture online or stored data

MIC Conductivity probe input

GND (I) Earth ground jack inputs (standard tip connectors)

GND (II) Earth ground jack inputs (standard tip connectors)

ANALOG Strip chart recorders input.

Use subminiature plug with positive tip.

BNC The port accepts pH, ORP with a BNC connector.

Ensure that the connector is clean and dry before

connecting.

ATC Phone jack input for the temperature probe for

automatic temperature compensation

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Sper scientific Messgerät Handbücher

Sper scientific

Sper scientific 840020 Bedienungsanleitung

Sper scientific

Sper scientific 840005 Bedienungsanleitung

Sper scientific

Sper scientific 840087 Bedienungsanleitung

Sper scientific

Sper scientific 850001 Bedienungsanleitung

Sper scientific

Sper scientific 840003 Bedienungsanleitung

Sper scientific

Sper scientific 840005 Bedienungsanleitung

Sper scientific

Sper scientific 840063 Bedienungsanleitung

Sper scientific

Sper scientific 800012 Bedienungsanleitung

Sper scientific

Sper scientific 850006 Installations- und Benutzerhandbuch

Sper scientific

Sper scientific 800046 Bedienungsanleitung

Sper scientific

Sper scientific 800047 Bedienungsanleitung

Sper scientific

Sper scientific DS-2013SD Bedienungsanleitung

Sper scientific

Sper scientific 850081 Bedienungsanleitung

Sper scientific

Sper scientific 800098 Bedienungsanleitung

Sper scientific

Sper scientific 850001E Bedienungsanleitung

Sper scientific

Sper scientific 840021 Bedienungsanleitung

Sper scientific

Sper scientific 840063 Bedienungsanleitung

Sper scientific

Sper scientific 840065 Bedienungsanleitung

Sper scientific

Sper scientific 850070 Bedienungsanleitung

Sper scientific

Sper scientific 850045 Bedienungsanleitung

Sper scientific

Sper scientific 850019 Bedienungsanleitung

Sper scientific

Sper scientific 850015 Bedienungsanleitung

Sper scientific

Sper scientific 850009 Bedienungsanleitung

Sper scientific

Sper scientific 840011 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung