Tenmars TM-201L Bedienungsanleitung

LUX/FC LED Light Meter

TM-201L / TM-209

User’s manual

HB2TM2090000

CONTENTS

1.Description.................................................... 1

2.Safety Precaution ......................................... 1

3.Preface ......................................................... 2

4.features......................................................... 3

5.Specifications................................................ 4

6.Operation ...................................................... 5

7.Luminous intensity measurement (TM-209)........... 8

8.Instrument Description of TM-201L............... 9

9.Instrument Description of TM-209............... 10

10.Attention...................................................... 12

11.Recommended Levels of Illumination ......... 13

12.Battery Replacement .................................. 15

13.End of life.................................................... 15

TM-201L/TM-209

EN-1

1. Description

Measures light from visible luminaries equipped with

white light LED, fluorescent, metal halide, high-pressure

sodium and incandescent sources.

2. Safety Precaution

CAUTION

Take extreme care for the following

conditions while measuring

zDo not operate the meter under the environment

with explosive gas (material), combustible gas

(material) steam or filled with dust.

zIn order to avoid reading incorrect data, please

replace the battery immediately when the symbol

“” appears on the LCD.

zIn order to avoid the damage caused by

contamination or static electricity, do not touch the

circuit board before you take any adequate action.

zOperating Environment: Indoors use. This

instrument has been designed for being used in an

environment of pollution degree 2.

zOperation Altitude: Up to 2000M.

zOperating Temperature & Humidity: 5 ~℃40 ,℃

0%~ 80%RH.

zStorage Temperature & Humidity: -10 ~℃60 ,℃

0%~ 70%RH.

zEMC: EN61326-1(2006), IEC 61000-4-2(2008, IEC

61000-4-3(2006) + (2007).

TM-201L/TM-209

EN-2

3. Preface

The flux of light received in a unit area of a certain side

being show is popularly known as illumination. In both

United Kingdom and America its unit is known as

footcandles light, but in Europe it is known as meter

candlelight.

One foot-candles light is the illumination of light that

falls on one side that lies in a distance one foot away

from a one foot-candlelight and exactly intersecting the

light. Its abbreviated form is written as 1 Fc=1 Lm/ft,

similarly, one-meter candlelight is the illumination of

light that falls on a side that lies in a distance one meter

away from a one meter candlelight and exactly

intersects the light. It is also called Lux i,e. the flux of

light being received in each sq. meter is called the

illumination of one lumen.

1 FC=10.764 LUX, 1 LUX=0.09290 FC,

therefore,Nbr. of foot (meter) candlelight =

Nbr. of Lumen

──────────────

Area(sq. foot or sq. meter)

Nbr. of Lumen=Nbr. of foot (or meter)x area

TM-201L/TM-209

EN-3

4. Features

zOverload Indication: LCD will show “OL” in the left

highest position.

zLow battery Indication” .

zSampling Rate: 2.5 times per second for digital

display.

zSpectral response close to CIE luminous spectral

efficiency.

zCosine Angular corrected.

zAccording to JIS C 1609:1993 and CNS 5119

general A class Specifications.

zMeasuring lights source: LED white light and all

visible light.

zMeasuring intensities of illumination in Lux or

footcandles.

zMany applications include: Warehouses, factories,

office buildings, restaurants, schools, library,

hospitals, photographic, many video, parking

garages, museums, art galleries, stadiums, building

security.

zData hold.

zMaximum hold.(TM-201L)

zMaximum/Average/Minimum Hold.(TM-209)

zZero adjustment.

zAuto power off and disable function.(TM-209)

zAuto ranging.(TM-209)

TM-201L/TM-209

EN-4

5. Specifications

Display of

TM-201L

2000 count, maximum display 1999

Display of

TM-209

4000 count, maximum display 3999

Sensor Silicon photodiode and filter

Measuring

Range of

TM-201L

200,2000, 20000,200000 Lux

20,200,2000,20000 Footcandles

Measuring

Range of

TM-209

40,400,4000, 40000,400000 Lux

40,400,4000,40000 Footcandles

Accuracy ±3% (Calibrated to standard

incandescent lamp 2856 K∘and

corrected LED day while light

spectrum)

8% other visible light source(TM-201L)

6% other visible light source(TM-209)

Angle deviation

from cosine

characteristics

30 ○±2%

60 ○±6%

80 ○±25%

Power Supply 9V NEDA 1604, IEC 6F22, JIS 006P

battery x 1pc

Battery life About 200 hours

Dimensions Meter: 38 (H) x 55(W) x 130(L) mm

1.5(H)x 2.2(W) x 5.1(L) inch

Sensor: 25(H) x 55(W) x 80(L) mm

9.8H)x 2.2(W) x 3.1(L) inch

Weight 250 g (include battery)

Accessories User’s manual, carrying case, 9V

battery

Length of wring for light sensor: Approx. 1.5M

TM-201L/TM-209

EN-5

6. Operation

1. Press the “ ” button to turn power on or off.

2. Remove sensor cap and place the sensor

perpendicular to the light.

3. Select LUX or FC.

4. When “OL” is shown at LCD, press the

button for useable reading. (TM-201L).

5. If you want to keep the reading value on the LCD

permanently after testing, press the “ ” button.

6. When done testing, replace the sensor cover to

protect the filter and sensor.

zData Hold

Freezes the reading present on the LCD at the

moment the button is pressed.

zR(TM-201L)

Press the manual ranging button for usable

reading.

zZERO (TM-201L)

Adjust 0 ADJ to enable LCD to indicate 000.

zZERO(TM-209)

Press the “ ” button for the zero adjustment if

any digits are appearing, when the light sensor

cap is not attached “CAP” is indicated. Make sure

that it is attached.

TM-201L/TM-209

EN-6

zM-H (TM-201L)

Press button to Lockup data maximal value

of measure data.

zMAX/AVG/MIN(TM-209)

Press button simultaneously Lockup data

maximum and average and minimum value of

measure data. Press the “ ”button more 1

seconds to disable this feature.

zLX/FC(TM-201L)

Illuminance Lux or Foot candle measuring select.

zLX/FC/CD(TM-209)

Illuminance Lux or Foot candle and luminous

intensity measuring select.

zL.S.(TM-209)

Light source select 1 ~ 9 features, each light

source can set correction parameters, default as

1.000. Calibration parameters can be set to 0.001

to 1.999, when the pressure L.S. KEY more than

1 second, LCD L.S. below the LN flashing,

pressure or change L1 to L9, pressure

LS KEY under 1 second right corner flashing

1.000, pressure or , you can change the

calibration parameters as to 0.995, the display

changes immediately, set 350.0x0.996 = 348.6,

Setup complete press “ ”> 1 second.

TM-201L/TM-209

EN-7

zL.S. (light source) factor:

L1ÎLEDwhitedaylight:0.99.

L2~L9ÎDefaultStandardlightsourceA:1.00.

zDisable Auto Power Off (TM-209)

When the power on, press the button more

than 1 second, to cancel or recovery automatically

shutdown." "This symbol representing

automatic shutdown feature is enabled.

zMEM(MOMORY) (TM-209)

Operate and press button <one second, store

one data, LCD displayed M and NO. 01~NO.99.

When display AVG in LCD right, operate

button at this moment, LCD display AVG M and

NO.01 ~ NO.99, present moment stores AVG value.

zREAD (READ MEMORY)(TM-209)

Pressure button > second display stored

value, LCD display M and NO. 01 ~ NO.99,

pressure or ,NO. 1 ÎNO. 2 until NO. 99,

as at that time, store data for AVG, will display in

the lower-left corner of the AVG. Press the 

button more 1 second to disable this feature.

zClear memory (TM-209)

When power off, press and button, then

LCD display “CLr” which means the memorized

data is erased.

Andere Handbücher für TM-201L

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Tenmars Messgerät Handbücher

Tenmars

Tenmars TM-731 Bedienungsanleitung

Tenmars

Tenmars TM-508A Bedienungsanleitung

Tenmars

Tenmars TM-93 Bedienungsanleitung

Tenmars

Tenmars TM-183 Bedienungsanleitung

Tenmars

Tenmars TM-4001 Bedienungsanleitung

Tenmars

Tenmars TM-188 Bedienungsanleitung

Tenmars

Tenmars TM-740 Bedienungsanleitung

Tenmars

Tenmars TM-101 Bedienungsanleitung

Tenmars

Tenmars ST-140 Bedienungsanleitung

Tenmars

Tenmars TM-741 Bedienungsanleitung

Tenmars

Tenmars TRIAXIAL ELF Bedienungsanleitung

Tenmars

Tenmars TM-1016 Bedienungsanleitung

Tenmars

Tenmars TM-411 Bedienungsanleitung

Tenmars

Tenmars SM206 Bedienungsanleitung

Tenmars

Tenmars TM-218 Bedienungsanleitung

Tenmars

Tenmars TM-190 Bedienungsanleitung

Tenmars

Tenmars TM-191 Bedienungsanleitung

Tenmars

Tenmars TM-215 Bedienungsanleitung

Tenmars

Tenmars TM-190 Bedienungsanleitung

Tenmars

Tenmars TM-186 Bedienungsanleitung

Tenmars

Tenmars TM-213 Bedienungsanleitung

Tenmars

Tenmars TM-206 Bedienungsanleitung

Tenmars

Tenmars TM-223 Bedienungsanleitung

Tenmars

Tenmars ST-130 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung

Konica Minolta

Konica Minolta BC-10 Plus Bedienungsanleitung