Tennsco 1470 Bedienungsanleitung

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on products.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply

in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

PK-1730918

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Standard Storage Cabinet

Unassembled Model 1470 or CVD1470

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

LOAD CAPACITIES PER SHELF LEVEL

36w x 18d 200 lbs.

UNIT SIZE WEIGHT CAPACITY

EVENLY DISTRIBUTED

ASSEMBLY OF 1470 or CVD1470 CABINET

Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.

Two people are recommended for assembly. Approximate assembly time: 30-40 minutes.

2. Place the cabinet back (Ref. No. 1) on a

protected surface to prevent

scratching the paint.

The ange on the

bottom of the back

should be facing upward.

1. The reference numbers used throughout this sheet refer

to the illustration on the back cover. This is to help you

to identify the various parts as they are mentioned.

3. Attach the left side (Ref. No. 2) to the back by placing

ange (A) around the back and bolting together with

seven bolts and nuts (Ref. Nos. 17 & 18). Be sure that the

lances on all shelf adjustment strips (B) are pointing in the

same direction.

5. Attach the right side (Ref. No. 3) to the back in the same manner

as you did in step 3, again, making sure that the ange is

around the back and that the lances on the shelf adjustment

strips are pointed in the same direction as those on the back and

left side. Push the side panel up so the studs in the top go

through the holes in the top

ange of the side and

fasten with three

nuts as in

step 4).

6. Attach the sill (Ref. No. 6) to the sides. Place nuts loosely on each

of the studs and slide the ends of the sill into the slots on both

sides of the unit. Then, securely tighten the nuts.

4. Attach the top (Ref. No. 5) to the unit by sliding the outer

ange over the back of the unit and the side ange on

the top over the side panel. The threaded studs should go

through the holes in the top

ange of the

side and

fasten with

three nuts.

Attach the

back to the

top using four

bolts and nuts.

7. Place the rear ange of the bottom (Ref. No. 7) into the

bottom lances of the back. The ange with two holes should

face the front, hanging over the sill. Insert the bolts through

the bottom and still with the head

facing the front of the unit.

Secure with

two nuts.

⁭

All lances point UP on

both backs and side.

Flange goes

under back.

Flange faces upward.

Flanges

face upward

Threaded studs go

through the holes

in the ﬂange at the

top of the side.

Slide ends in to the slots

on the bottom of the sides.

Nuts placed loosely

on studs of the sill.

Insert bottom into

bottom lances.

⁭

NOTE: When bolting the unit together, leave

the bolts slightly loose until Step 8, unless

otherwise speciﬁed.

NOTE: All illustrations show a solid door. Assembly

for C-Thru doors (CVD1470) is identical.

Two holes must

be in front

⁭

8. Set the unit upright and tighten

all nuts around the entire unit.

10. Attach the left door

(Ref. No. 8) to the

unit by placing the

door on the hinges,

aligning the hinge

holes, and dropping

the hinge pins (Ref.

No. 15) into the slots.

Then, tap the top of

each hinge pin until

fully seated.

Leveler

Access Holes

9. Insert the four shelves (Ref. No. 4)

at your desired levels.

NOTE: In order to place the

shelves, you must ﬁrst tilt

the shelf slightly to the left

or right before inserting

into the unit.

12. The cabinet must be

level in order for the

doors to close

properly. Levelers

may be adjusted by

placing the nut driver

through the hole in

each end of the sill

and adjusting the

leveling screw.

11. Attach the right door

(Ref. No. 9) to the unit

in the same way you

attached the left door.

⁭

1. Place the locking handle

(Ref. No. 11) on the right

hand door and fasten with

two #8-32 X 1/4hex-head

bolts and lock washers,

provided with the handle.

2. Turn the handle to the

open position and

place the locking cam

(Ref. No. 12) over the

square shank of the

door handle. The latch

must be facing downward

as shown. Then place the

locking cotter pin (Ref. No.

13) through the hole of the

square shank.

3. With the handle still in the open position, hook the

locking bars (Ref. No. 10) to the locking cam (see

“A” at left). Once in position, slowly rotate the door

handle to the closed position so the lock bars

prot rude from the holes at the top and bottom

of the door (shown at right, below).

4. Slide the nylon lock bar

guide inserts (Ref. No.

14) over the lock bar

ends and through the

door slots (see “B” at

right). Push down rmly

until the guides snap

into place.

Handle/Locking System Installation

⁭

⁭⁭

⁭

REPLACEMENT PARTS

⁭

Tennsco Nut Driver

(Ref No. 16)

Bottom

(Ref No. 7)

Sill

(Ref No. 6) Hinge Pins

(Ref No. 15)

Left Side

(Ref No. 2) Top

(Ref No. 5)

Shelf

(Ref No. 4)

Right Side

(Ref No. 3)

Cotter Pin

(Ref No. 13)

Locking Bar Guide

Nylon Insert

(Ref No. 14)

Locking Bar Set

(Ref No. 10)

Locking Cam

(Ref No. 12)

Locking Handle

with Keys

(Ref No. 11)

Back Panel

(Ref No. 1)

REF. NO. DESCRIPTION

1 Back Panel 1 944BA

2 Left Side 1 944LS

3 Right Side 1 944RS

4 Shelf 4 301

5 Top 1 944TON

6 Sill 1 944SIN

7 Bottom 1 944BO

8 Left Door: Solid for 1470 1 944LD

Left Door: C-Thru for CVD1470 (not shown above) 1 CVD-72LD

9 Right Door: Solid for 1470 1 944RD

Right Door: C-Thru for CVD1470 (not shown above) 1 CVD-72RD

10 Locking Bar Set 1 944LB

11 Locking Handle w/keys & hardware 1 944LH

12 Locking Cam* 1 944LC

13 Cotter Pin* 1 CTRPN

14 Locking Bar Guide Insert (Nylon)* 2 944GI

15 Hinge Pins* 6 944HP

16 Tennsco Nut Driver 1 TOOL-2

17 #8-32 x 3/8” bolts (not shown above) 20 **

18 #8-32 nuts (not shown above) 30 **

*Included in Ref. No. 11, locking handle with keys and hardware (Part No. 944LH). **Available Locally

QTY. PART NO.

⁭

Left Door

(Ref No. 8)

Right Door

(Ref No. 9)

NOTE: Additional hardware may be included for replacement purposes.

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

49B173

Dieses Handbuch passt für folgende Modelle

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco Standard Combination Cabinet CVD7214 Bedienungsanleitung

Tennsco

Tennsco 1470RH Bedienungsanleitung

Tennsco

Tennsco 1480 Bedienungsanleitung

Tennsco

Tennsco 1842 Bedienungsanleitung

Tennsco

Tennsco DWR-4218 Bedienungsanleitung

Tennsco

Tennsco 7218 Bedienungsanleitung

Tennsco

Tennsco STK-151872-1 Bedienungsanleitung

Tennsco

Tennsco RGL-1236S Bedienungsanleitung

Tennsco

Tennsco J2478C Bedienungsanleitung

Tennsco

Tennsco Z-Line Steel Shelf Unit Bedienungsanleitung

Tennsco

Tennsco J1878A-N Bedienungsanleitung

Tennsco

Tennsco APT-3672S Bedienungsanleitung

Tennsco

Tennsco RGL-1236S Bedienungsanleitung

Tennsco

Tennsco B-8400 Bedienungsanleitung

Tennsco

Tennsco 7224 Bedienungsanleitung

Tennsco

Tennsco Imperial Shelving 3630 Bedienungsanleitung

Tennsco

Tennsco EB-12 Bedienungsanleitung

Tennsco

Tennsco BK6-121812-1 Bedienungsanleitung

Tennsco

Tennsco J1878A-N-W Bedienungsanleitung

Tennsco

Tennsco ESPC-1236 Bedienungsanleitung

Tennsco

Tennsco B-3000 Bedienungsanleitung

Tennsco

Tennsco WELDED 3-PERSON LOCKER Bedienungsanleitung

Tennsco

Tennsco Open Foreman's Desk Bedienungsanleitung

Tennsco

Tennsco L&T Hinged Door Kit Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung