Tennsco 1870 Bedienungsanleitung

GENERAL SAFETY INFORMATION

Some parts may have sharp edges. CARE must be taken when handling various pieces to avoid injury.

For safety, wear a pair of work gloves when assembling or performing any maintenance on products.

LIMITED WARRANTY

Tennsco warrants goods purchased hereunder to be free of defects in materials and workmanship for a period of one (1) year from the date of shipment, hereunder. This warranty shall not apply

in the event goods are damaged as a result of misuse, abuse, neglect, accident, improper application, modication or repair by persons not authorized by Seller, where goods are damaged during

shipment, or where the date stamps on the goods have been defaced, modied or removed. UNLESS CONSIDERED UNENFORCEABLE OR UNLAWFUL UNDER APPLICABLE LAW:

a. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO WARRANTIES OR MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY EXCLUDED:

b. BUYERS REMEDY, IF ANY, FOR ANY DEFECTIVE GOODS SHALL BE LIMITED TO A REFUND BY SELLER OR REPLACEMENT OF THE GOODS AT SELLER’S OPTION, AND SHALL IN NO

EVENT INCLUDE DAMAGES OF ANY KIND, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.

NO GOODS ACCEPTED FOR RETURN WITHOUT PRIOR APPROVAL. Seller shall have the right to inspect any goods claimed to be defective at Buyers place of business or require Buyer to return the

goods to Seller for inspection on Seller’s premises. Transportation charges covering returned goods will be borne by Seller only if such goods are proven to be defective, are covered by this warranty

and are returned within the warranty period stated above.

PK-1810918

ASSEMBLY INSTRUCTIONS & PARTS MANUAL

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE

Deluxe Storage Cabinet

Unassembled Models 1870 & 2470

Tennsco LLC., Dickson, TN 37056-1888 • (866) 446-8686

LOAD CAPACITIES PER SHELF LEVEL

36w x 18d

36w x 24d

200 lbs.

UNIT SIZE WEIGHT CAPACITY

EVENLY DISTRIBUTED

ASSEMBLY OF 1870 OR 2470 CABINET

Tools Needed: A free 11/32” nut driver is included with each Tennsco cabinet.

Two people are recommended for assembly. Approximate assembly time: 20-30 minutes.

2. Place the cabinet back (Ref. No. 1) on a protected surface

to prevent scratching the paint. The ange on the bottom of

the back should be facing upward.

1. The reference numbers used throughout this sheet refer to

the illustration on the back cover. This is to help you to

identify the various parts as they are mentioned.

3. Attach the left side (Ref. No. 2) to the back by placing

ange (A) around the back and bolting it together

with seven bolts and nuts Ref. Nos. 15 & 16). Be sure that

the lances on all shelf adjustment strips (B) point in the

same direction.

5. Insert one shelf (Ref. No. 4) into the approximate center

of the unit, inserting the shelf edges into the lances on

all four shelf adjustment strips. Be sure that the channeled

edge of the shelf is toward the cabinet front.

6. Place the top (Ref. No. 5) onto the unit. Be sure that the

anges tuck inside the cabinet sides and back. Secure

with eleven nuts and bolts. The front part of the top will

bolt into place in step 8.

4. Attach the right side (Ref. No. 3) to the back in the same

manner as in step 3, again making sure that the ange

is around the back and that the lances on the shelf

adjustment strips are pointed in the same direction as those

on the back and left side.

7. With both doors in the closed position, lift the door

and frame assembly (Ref. No. 6) and place it over the

cabinet body. Be aware that the door latches have not

yet been attached,

All lances point UP on

the back and side.

Flanges

face upward

⁭

so the doors could

potentially swing

open if the door

frame is held in

an upsidedown

position. The

door frame should

cover the outside

edges of the

entire storage

cabinet front.

⁭

NOTE: When bolting the unit together, leave

the bolts slightly loose until Step 10, unless

otherwise speciﬁed.

Flange faces upward.

⁭

Flange goes

under back.

⁭

1. Place the locking handle

(Ref. No. 9) on the right

hand door and fasten with

two #8-32 X 1/4 hex-head

bolts and lock washers,

provided with the handle.

2. Turn the handle to the

open position and

place the locking cam

(Ref. No. 10) over the

square shank of the

door handle. The latch

must be facing downward

as shown. Then place the

locking cotter pin (Ref. No.

12) through the hole of the

square shank.

3. With the handle still in the open position, hook the

locking bars (Ref. No. 8) to the locking cam (see

“A” at left). Once in position, slowly rotate the door

handle to the closed position so the lock bars

prot rude from the holes at the top and bottom

of the door (shown at right, below).

4. Slide the nylon lock bar

guide inserts (Ref. No.

11) over the lock bar

ends and through the

door slots (see “B” at

right). Push down rmly

until the guides snap

into place.

5. Attach the “dummy” handle

(Ref. No. 13) using two

#8-32 X 1/4 hex-head bolts

and lock washers.

Handle/Locking System Installation

8. With the door and frame assembly in place, attach it

securely to the unit by opening each

door, one at a time, and securing

the frame assembly using

two bolts and twenty

nuts. This will

require attaching

nuts to the

nine pre-welded

studs along

each side, plus

two bolts and

nuts along the top.

Using two people, set the unit upright and tighten all nuts

around the entire unit. Insert the remaining shelves at your

desired levels. The shelf you inserted earlier may also be moved

to a different level if desired.

10.

Two holes

must be in front.

Insert shelf

into bottom lances.

⁭

Levelers

Access Holes

11. The cabinet must be

level in order for the

doors to close properly.

Levelers may be adjusted

by placing the nut driver

through the hole in each

end of the sill and adjusting

the leveling screw.

NOTE: In order to place

the shelves, you must

ﬁrst tilt the shelf slightly

to the left or right before

inserting it into the unit.

⁭⁭⁭⁭

9. Place the the bottom (Ref. No. 7) in the lowest notch of the

shelf adjusting strips on the back. Make sure the ange with

two holes faces the front, and that it is over the ange of the

frame sill. If necessary, you may

push out on the side

walls to

enable

the bottom

to more

easily slide

into position. Attach

the shelf securely by bolting

the bottom to the frame sill

with two bolts and nuts.

⁭⁭

⁭

REPLACEMENT PARTS

⁭

Tennsco Nut Driver

(Ref No. 14)

Bottom

(Ref No. 7)

Dummy Handle

(Ref No. 13)

Left Side

(Ref No. 2) Top

(Ref No. 5)

Shelf

(Ref No. 4)

Right Side

(Ref No. 3)

Cotter Pin

(Ref No. 12)

Locking Bar Guide

Nylon Insert

(Ref No. 11)

Locking Bar Set

(Ref No. 8)

Locking Cam

(Ref No. 10)

Locking Handle

with Keys

(Ref No. 9)

Back Panel

(Ref No. 1)

REF. NO. DESCRIPTION

1 Back Panel 1 043BA 1 043BA

2 Left Side 1 043LS 1 044LS

3 Right Side 1 043RS 1 044RS

4 Shelf 4 301 4 302

5 Top 1 043TO 1 044TO

6 Door & Frame Assembly 1 043DA 1 043DF

7 Bottom 1 043BO 1 044BO

8 Locking Bar Set 1 043LB 1 043LB

9 Locking Handle w/keys & hardware 1 043LH 1 043LH

10 Locking Cam* 1 944LC 1 944LC

11 Locking Bar Guide Insert (Nylon)* 2 944GI 2 944GI

12 Cotter Pin* 1 CTRPN 1 CTRPN

13 Dummy Handle* 1 043DH 1 043DH

14 Tennsco Nut Driver 1 TOOL-2 1 TOOL-2

15 #8-32 x 3/8” bolts (not shown above) 31 ** 31 **

16 #8-32 nuts (not shown above) 47 ** 47 **

*Included in Ref. No. 9, locking handle with keys and hardware (Part No. 043LH). **Available Locally

QTY. PART NO.

⁭

Door & Frame

Assembly

(Ref No. 6)

NOTE: Additional hardware may be included for replacement purposes.

QTY. PART NO.

1870 (18”D Cabinet) 2470 (24”D Cabinet)

⁭

Tennsco makes every effort to ensure that all units ship complete with all parts and arrive undamaged.

However, should your unit contain missing or damaged parts, please contact your purchase location.

49B181

Dieses Handbuch passt für folgende Modelle

Andere Tennsco Inneneinrichtung Handbücher

Tennsco

Tennsco J1878A-N Bedienungsanleitung

Tennsco

Tennsco J1878A-N-W Bedienungsanleitung

Tennsco

Tennsco 1842 Bedienungsanleitung

Tennsco

Tennsco CC-30 Bedienungsanleitung

Tennsco

Tennsco L&T Hinged Door Kit Bedienungsanleitung

Tennsco

Tennsco Enclosed Foreman’s Desk Bedienungsanleitung

Tennsco

Tennsco JUMBO Gebrauchsanweisung

Tennsco

Tennsco FS350 Bedienungsanleitung

Tennsco

Tennsco 1276 Series Bedienungsanleitung

Tennsco

Tennsco BK6-121512-3 Bedienungsanleitung

Tennsco

Tennsco 7218 Bedienungsanleitung

Tennsco

Tennsco APT-3672S Bedienungsanleitung

Tennsco

Tennsco WBHC-1516-MGY Bedienungsanleitung

Tennsco

Tennsco 1472 Bedienungsanleitung

Tennsco

Tennsco 2476 Series Bedienungsanleitung

Tennsco

Tennsco 1470 Bedienungsanleitung

Tennsco

Tennsco 7818 Bedienungsanleitung

Tennsco

Tennsco CINCO NIVELES Bedienungsanleitung

Tennsco

Tennsco 1442 Bedienungsanleitung

Tennsco

Tennsco zt7 Series Bedienungsanleitung

Tennsco

Tennsco ESPC-1236 Bedienungsanleitung

Tennsco

Tennsco Capstone Shelving Units Bedienungsanleitung

Tennsco

Tennsco 1436 Bedienungsanleitung

Tennsco

Tennsco Sliding Door Jumbo Storage Cabinet JSD2478SU Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung