Town & Country Fireplaces TCWS.54OD Bedienungsanleitung

MODEL:

TCWS.54OD SERIES C w/ screen

TCWS54 OUTDOOR GAS

FIREPLACE INSTALLATION AND

OPERATING INSTRUCTIONS

220421-20 TCWS.54 OD W SCREEN 100005095

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Visit www.townandcountryﬁreplaces.net for the most recent version of this manual

WARNING: If the information in these

instructions is not followed exactly, a re

or explosion may result causing property

damage, personal injury or death.

DANGER: If you smell gas:

1. Shut off gas to the appliance

2. Extinguish any open ame.

3. If odor continues, keep away from the

appliance and immediately call your gas

supplier or re department.

WARNING:Do not store or use gasoline or other

ammable vapors and liquids in the vicinity of

this or any other appliance.

An LP-cylinder not connected for use shall

not be stored

WARNING: Improper installation, adjustment,

alteration, service or maintenance can cause

injury or property damage. Read the installa-

tion, operating and maintenance instructions

thoroughly before installing or servicing this

equipment.

CARBON MONOXIDE HAZARD

This appliance can produce carbon

monoxide which has no odor.

Using it in an enclosed space can

kill you.

Never use this appliance in an

enclosed space such as a camper,

tent, car or home.

SERIAL #

Installation and service must be performed

by a qualied installer, service agency or the

gas supplier.

WARNING:

For Outdoor Use Only

TCWS.54OD W SCREEN_220421-20

Table of Contents

HOT GLASS WILL CAUSE

BURNS.

DO NOT TOUCH GLASS UNTIL

COOLED.

NEVER ALLOW CHILDREN TO

TOUCH GLASS.

DANGER

Table of Contents ...................................................................... 2

Caution ...................................................................................... 3

Safety ........................................................................................ 3

Important Note for the Commonwealth of Massachusetts ....... 4

This Fireplace Is Intended For Outdoor Use Only! .................... 5

Propane Conversion .................................................................. 6

Fireplace Dimensions ................................................................ 7

Minimum Clearances to Combustible Material ......................... 7

Mantel Clearance Chart ..................................................... 7

Installation Requirements .......................................................... 8

Window Frame Removal ........................................................... 8

Standoffs ................................................................................... 9

Locating The Fireplace .............................................................. 9

Framing and Finishing ............................................................. 10

Steel Stud Framing Kit Dimensions ................................. 10

Minimum Combustible .................................................... 11

Framing Dimensions ........................................................ 11

Non-Combustible Board Detail........................................ 11

Non-Combustible Recessed Installation Detail ............... 11

Steel Stud Framing Kit ............................................................ 12

Frame assembly............................................................... 13

Screen Installation ................................................................... 15

Honeywell Control Valve Plumbing and Electrical ................... 16

Installation ........................................................................ 16

Gas Supply .............................................................................. 17

Gas Pressure Check ................................................................ 17

Correct gas pressure requirement.................................... 17

Venting ..................................................................................... 18

Roof Termination Venting Chart ............................................... 18

Ceiling Opening................................................................ 19

Ceiling Firestop ................................................................ 19

Vent Pipe .......................................................................... 19

Roof Support Bracket ...................................................... 19

Roof Vent Terminal ........................................................... 20

Vent Terminal Clearance .......................................................... 21

Vent Pipe Sealant .................................................................... 22

Vent Restrictor Adjustment ..................................................... 23

Firebox Panels Installation ...................................................... 24

Lighting Instructions ................................................................ 25

First Fire ................................................................................... 25

Maintenance ............................................................................ 26

Glass Panel: ..................................................................... 26

Annual Inspection:............................................................ 26

Periodically:...................................................................... 26

TCWS.54CODE Replacement Parts ........................................ 27

Honeywell Control System Replacement Parts ...................... 28

Wiring Diagram ........................................................................ 29

Roof Termination Kit ................................................................ 30

Vent Pipe Dimensions ............................................................. 31

Vent Offset Chart ..................................................................... 32

Quick Panel Removal for Valve Service .................................. 33

Rating Label Location ............................................................. 34

WARNING: This product

can expose you to chemicals

including ceramic bers,

which are known to the State

of California to cause cancer, and carbon

monoxide, which is known to the State of

California to cause birth defects or other

reproductive harm.

For more information go to

www.P65Warnings.ca.gov.

This warning is applicable to all

Paciﬁc Energy Fireplace Products

100005095 TCWS.54OD W SCREEN_220421-20

FOR YOUR SAFETY - Do not install or operate your Town & Country re-

place without rst reading and understanding this manual. Any installation or

operational deviation from the following instructions voids the Town & Country

Fireplaces Warranty and may prove hazardous.

This appliance and its individual shut off valve must be disconnected from gas

supply piping system during any pressure testing of that system at test pres-

sures in excess of 1/2 psig (3.5 kPa).

This appliance must be isolated from the gas supply piping system by closing

its individual manual shut off valve during any pressure testing of the gas sup-

ply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa).

Note: When lit for the rst time, the appliance will emit a slight odour for a

couple of hours. This is due to the curing of paints, sealants and lubricants

used in the manufacturing process. This condition is temporary. Open doors

and windows to ventilate area. Smoke and fumes caused by the curing pro-

cess may cause discomfort to some individuals.

Do not use the replace if any part has been under water. Immediately call a

qualied service technician to inspect the replace and to replace any part of

the control system and any gas control which has been under water.

Due to high temperatures, this gas appliance should be located out of trafc and away from furniture and draperies.

Children and adults should be alerted to the hazards of high surface temperatures and should stay away to avoid burns

or clothing ignition.

Young children should be carefully supervised when they are in the same room as the appliance.

Clothing or other ammable material should not be placed on or near the appliance.

Any grill, panel or door removed for servicing the unit must be replaced prior to operating. Failure to do so may create a

hazardous condition.

Installation and repair should be done by a qualied service person. The appliance should be inspected before use and

at least annually by a professional service person. More frequent cleaning may be required due to excessive lint from

carpeting, bedding material, etc. It is imperative that control compartments, burners and circulating air passageways of

the appliance be kept clean.

It is our policy that no responsibility is assumed by the Company or by any of its employees or representatives for any

damages caused by an inoperable, inadequate, or unsafe condition which is the result, either directly or indirectly, of any

improper operation or installation procedures.

This appliance must not be connected to a chimney ue serving a separate solid fuel burning appliance.

Safety

We recommend that our gas hearth

products be installed and serviced

by professionals who are certied

in the United States by the National

Fireplace Institute® (NFI) as NFI

Gas Specialists

Caution

3100005095TCWS.54OD W SCREEN_220421-20

Important Note for the Commonwealth of Massachusetts

From Massachusetts Rules and Regulations 248 CMR 5.08:

(a) For all side wall horizontally vented gas fuelled equipment installed in every dwelling, building or structure used in whole or in part for residential

purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7) feet above

nished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall be satised.

1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fuelled equipment, the

installing plumber or gas tter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is installed on the oor level

where the gas equipment is to be installed, in addition, the installing plumber or gas tter shall observe that a battery operated or hard-wired carbon

monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure served by the side wall horizontal vented gas

fuelled equipment. It shall be the responsibility of the property owner to secure the services of qualied licensed professionals for the installation of

hard-wired carbon monoxide detectors.

a. In the event that the side wall horizontally vented gas fuelled equipment is installed in a crawl space or an attic, the hard-wired carbon monoxide

detector with alarm and battery back-up may be installed on the next adjacent oor level.

b. In the event that the requirements of this subdivision cannot be met at the time of completion of installation, the owner shall have a period of thirty

(30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon monoxide detec-

tor with an alarm shall be installed.

2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions shall

comply with NFPA 720 and be ANSI/UL 2034 listed as IAS certied.

3. SIGNAGE. A metal or plastic identication plate shall be permanently mounted to the exterior of the building at a minimum height of eight (8) feet

above grade directly in line with the exhaust vent terminal for the horizontally vented gas fuelled heating appliance or equipment. The sign shall read, in

print size no less than one-half (1/2) inch in size, “GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL OBSTRUCTIONS”.

4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fuelled equipment shall not approve the installation unless,

upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR 5.089(2)(a) 1

through 4.

(b) EXEMPTIONS. The following equipment is exempt from 248 CMR 5.089(2)(a) 1 through 4.

1. The equipment listed in Chapter 10 entitled “Equipment Not Required To Be Vented” in the most current edition of NFPA 54 as adopted by the

Board; and

2. Product Approved side wall horizontal vented gas fuelled equipment installed in a room or structure separate from the dwelling, building or struc-

ture used in whole or in part for residential purposes.

wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the instructions provided by

the manufacturer for installation of the equipment and the venting system shall include:

1. Detailed instructions for the installation of the venting system design or the venting system components; and

2. A complete parts list for the venting system design or venting system.

(d) MANUFACTURER REQUIREMENTS – GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a Product Approved

side wall horizontally vented gas fuelled equipment does not provide the parts for venting the fuel gases, but identies “special venting systems”, the fol-

lowing requirements shall be satised by the manufacturer.

1. The referenced “special venting system” instructions shall be included with the appliance or equipment installation instructions; and

2. The “special venting systems” shall be Product Approved by the Board, and the instructions for that system shall include a parts list and detailed

installation instructions.

(e)) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fuelled equipment, all venting instructions, all parts

lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipment at the completion of the installation.

100005095 TCWS.54OD W SCREEN_220421-20

WARNING: Solid fuels

should not be burned in

this appliance.

Warning:

This appliance is only for use

with the type of gas indicated

on the rating plate. This ap-

pliance is not convertible for

use with other gases, unless

a certied kit is used.

• The replace must be located inside of a weatherproof enclosure.

• Flashing must be installed around the replace opening in accordance

with local building codes in order to prevent moisture from entering the

enclosure.

• A drip pan (not supplied with the unit) must be installed under the

replace and be provided with a means of draining.

• Care must be taken to select materials and building practices which will

protect the enclosure and replace from exposure to moisture.

• Not for use with a power vent.

This Fireplace Is Intended For Outdoor Use Only!

5100005095TCWS.54OD W SCREEN_220421-20

Propane Conversion

1. Remove the compression tting

from the bottom of the orice

housing and gently tap the pilot

in your hand. The natural gas

orice should fall out (Figure 1).

2. Insert the propane orice that

came in your instruction pack

as shown into the orice hous-

ing and reattach the pilot to the

compression tting and pilot tube

(Figure 2) & (Figure 3).

3. Using the valve conversion kit

that came in the instruction pack,

convert the valve to propane fol-

lowing the instructions provided

with the kit (Figure 4).

ORIFICE

COMPRESSION

FITTING

ORIFICE

HOUSING

COMPRESSION

FITTING

ORIFICE

HOUSING

Figure 1: PILOT.

Figure 2: Orice insert.

ORIFICE

Figure 3: ORIFICE.

Figure 4: Valve conversion kit.

THIS FIREPLACE IS DESIGNED

FOR USE WITH A HONEYWELL

PILOT, DO NOT USE ANY

OTHER PILOT WITH YOUR

OUTDOOR FIREPLACE.

100005095 TCWS.54OD W SCREEN_220421-20

29 3/4"

24"

4“

CEILING

ADJACENT WALL

OR MANTEL SUPPORT

6”

COMBUSTIBLE FLOOR

COMBUSTIBLE HEARTH

Figure 6: Mantel clearances.

Figure 7: Mantel.

* MANTEL CLEARANCE

A 9”

B 6”

C 3”

** MANTEL DEPTH

D 12”

E 6 3/4”

F 1 1/2”

Mantel Clearance

Chart

UNIT MAY BE RECESSED UP TO 6” WITH

NONCOMBUSTIBLE MASONRY TYPE MATERIAL

Minimum Clearances:

Side standoffs ....................................................... 0 in. (0 mm)

Back standoffs ...................................................... 0 in. (0 mm)

Top standoffs ........................................................0 in. (0 mm)

Bottom of appliance..............................................0 in. (0 mm)

Adjacent side wall.................................................4 in. (102 mm)

Ceiling to appliance ............................................24 in. (610 mm)

*Mantel to appliance .................. ..........See Figure #6

**Maximum Mantel extension .. ..........See Figure #6

Mantel support...................................................... 4 in. (102 mm)

Vertical vent pipe ..........................................1 3/4" in. (45 mm)

74 3/4”

18”

55”

74 3/4”

53 7/8”

25 3/4”

13 5/8”

29 3/4”

28 5/8”

36 7/8” 37 7/8”

Figure 5: TCWS.54 OD with Screen dimensions.

MAY USE COMBUSTIBLE

FACING MATERIAL IN THIS AREA

NON-COMBUSTIBLE

FINISH MATERIAL

SEE FIG #8 & 9

NON-COMBUSTIBLE ZONE.

DO NOT INSTALL ANY COMBUSTIBLE MATERIAL,

ELECTRICAL WIRING OR GAS PLUMBING IN THIS

AREA.

COMBUSTIBLE FRAMING AND

FINISH WALL ABOVE STANDOFFS

STANDOFFS

STEEL FRAMING

FIREPLACE FRONT

TOP OF LINTEL BAR

7100005095TCWS.54OD W SCREEN_220421-20

Fireplace Dimensions

Minimum Clearances to Combustible Material

Warning: Turn off the replace, and allow ample time for the unit to cool before proceeding.

Caution: The ceramic glass is very fragile, and should be handled with care.

The window frame is held in place by two spring-loaded latches that are operated by a one-piece latch handle.

1. Remove the TC Finishing Touch Trim Kit from the window frame. (If installed)

2. Using a screwdriver or other similar object, push against the notch in the top of the latch and grab the bottom of the

latch handle as it protrudes. Lift handle until latch hook disengages (Figure 8) & (Figure 9). Repeat for other side while

holding glass so it does not tip out.

3. Tilt the top of the window frame out to clear the top edge of the unit. Grasp the sides of the frame and lift up and out

to disengage from its bottom track.

4. Place the window frame in a safe place to avoid damage.

5. Re-assemble in reverse order. Latch handle should snap into place and be ush with window frame when engaged

correctly.

6. Reinstall Trim Kit if required.

TIP:

To ensure glass is properly latched, grasp the top left and right

sides of the glass frame, under moderate pressure it should pull

forward and return to original position evenly on both sides.

HANDLE

Figure 8: Accessing handle. Figure 9: Handle.

The Town & Country Fireplace installation and venting must conform to the current CAN/CGA-B149 installation code (in

Canada) or the current National Fuel Gas Code, ANSI Z223.1 (in the USA), and approved per local codes. Only qualied

(licensed or trained) personnel should install this product.

In the state of Massachusetts, only a licensed Plumber and Gas Fitter may install this product.

100005095 TCWS.54OD W SCREEN_220421-20

Installation Requirements

Window Frame Removal

The standoffs are shipped loose inside the replace and must be installed on the top and the side of the replace as

shown in (Figure 10). Do this once the replace is on site and in position.

In planning the installation for the replace, it is necessary to determine where the unit is to be installed, location of vent

system and where gas supply piping may be plumbed. Various installations are possible, such as, into an existing wall,

a corner, a built-in wall or a wall projection (Figure 11). Due to high temperatures, do not locate this replace in areas of

high trafc or near furniture or draperies.

The minimum clearances from the replace to combustible surfaces must be adhered to and are shown in Figure 6 & 7.

Figure 11: TCWS54CODE Possible locations.

EXAMPLES OF COMMON LOCATIONS

SEE FIG #15 FOR DIMENSIONS

TOP STANDOFFS

SIDE

STANDOFF

(THIS SIDE ONLY)

Figure 10: TCWS54CODE standoffs.

HANDLE

CONTROL

BOX

9100005095TCWS.54OD W SCREEN_220421-20

Locating The Fireplace

Standoffs

Note: The ﬁreplace should be in place

and venting installed before framing

in or building an enclosure around the

unit.

The Town & Country replace must be

framed in as described below or totally

enclosed with non-combustible material,

such as facing brick.

Determine the total thickness of facing

material to be used. The framing Kit is

adjustable, and will allow for 3/8” to 1-3/8”

nishing surface to be ush with the front

of the unit. If preferred, additional masonry

type non-combustible material can be

installed above and to the sides up to 6

inches forward of the appliance.

*The ﬁnishing material must not inter-

fere with glass frame access.*

A Steel Stud Framing Kit is supplied with

the replace and must be used unless the

replace is totally enclosed with non-com-

bustible material. Assemble the framing kit

as per the instructions on pages 11 - 13

of this manual. Attach the steel frame to

the replace once the replace is in its

nal position. Set the depth and secure

the steel frame to the framing brackets on

each side of the unit. Ensure that the studs

are set back far enough to allow for thick-

ness of nishing surface.

The sides, back and top of the replace

can be framed in up to the steel studs and

the replace standoffs using conventional

lumber. Consult local building codes for

specic requirements.

Due to high temperatures, non-combusti-

ble backer board, such as cement board

or its equivalent, must be used to sheet

in the front of the replace, extending

12" below, 12” above and 9 5/8" to the

side of the framing edge bars (Figure 13).

Standard sheetrock (dry wall) may be used

beyond this.

If the backer board is not to be nished

with other non-combustible material

such as tiles, it is recommended that the

instructions in (Figure 15) be followed

closely.

Fabricate and install appropriate ashing

to local building code.

Note: Installing unit without ﬂashing

installed will void the warranty

Note: Provide proper drainage to divert

water underneath the unit

Chase Insulation: When installing this

replace against a non-insulated exterior

wall or chase, it is recommended that

the outer walls be insulated to the same

degree as other exterior walls. Do not

place replace directly against the insu-

lation. Cover the insulation and plastic

vapour barrier with a solid surface, such

as dry wall (sheetrock). Consult local

codes. Do not insulate or use plastic

vapour barrier within the framing kit.

CAUTION: SEE (Figure 15) BEFORE

PROCEEDING.

76”

55”

Figure 12: TCWS54CODE with supplied steel frame.

ALL OTHER FRAMING CAN

BE DONE WITH

CONVENTIONAL LUMBER

NON-COMBUSTIBLE ZONE. DO NOT INSTALL ANY

COMBUSTIBLE MATERIAL, ELECTRICAL WIRING,

INSULATION, PLASTIC VAPOR BARRIER OR GAS

PLUMBING WITHIN THE STEEL STUD FRAMING

Steel Stud Framing Kit Dimensions

(Supplied with ﬁreplace)

100005095 TCWS.54OD W SCREEN_220421-20

Framing and Finishing

Andere Handbücher für TCWS.54OD

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Town & Country Fireplaces Kamin im Innenbereich Handbücher

Town & Country Fireplaces

Town & Country Fireplaces Architectural Series Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54.NG03C2 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCW120 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36D2 ARCH Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54.CE2 Series C Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54CE3 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ST.NGST04D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC54 SERIES DMODULAR Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces Model TC42SeriesC Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54ST SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS54 SERIES D Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC30 Black Diamond Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36ST Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCHF.22BODYA Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces TCWS.54NG04.C2 Technisches Handbuch

Town & Country Fireplaces

Town & Country Fireplaces D2 Series Installations- und Betriebshandbuch

Town & Country Fireplaces

Town & Country Fireplaces TC36 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch