Vacmaster VWM510 Bedienungsanleitung

Wet/Dry Vacuums

Operator’s Manual

Wall Mountable Wet/Dry Vacuum

Model No.VWM510

FOR YOUR SAFETY

Read and understand this manual before use

Keep this manual for future reference

VW01BZ.20.60.01

www.vacmaster.com

Cleva North America

44 Parkway Commons, Greer, SC 29650

SECTION Page

Thank you for purchasing this Vacmaster®wet/dry vacuum cleaner. Feel confident that with

Vacmaster®you are obtaining a high quality product engineered for optimal performance. This

vacuum is capable of picking up liquids and dry materials.

FOR YOUR SAFETY: CAREFULLY READ AND UNDERSTAND ALL INSTRUCTIONS

We take pride in producing a high quality, durable product. This Vacmaster®product carries a limited two (2)

year warranty against defects in workmanship and materials from date of purchase under normal household

use. If product is to be used for commercial, industrial or rental use, a 90 day limited warranty will apply.

Warranty does not apply to defects due to direct or indirect abuse, negligence, misuse, accidents, repairs or

alterations and lack of maintenance. Please keep your receipt as proof of purchase. This warranty gives

you specific legal rights, and you may have other rights, which vary form state to state. For product service

call Customer Service at (866) 384-8432

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

TABLE OF CONTENTS

WARRANT

Warranty……………………………………………………………………………………..………

Safety Instructions and Warnings………………………………………………………..……….

Double Insulation Instructions....………………………………………………………….………

Extension Cord…………………………………………………………………………….……….

Unpacking and Checking Carton Contents………….……………………..………….…….…..

General Assembly Instructions…………………………………………………………….….…..

Dry Vacuum Operation………………………………………………………………………..……

Liquid Vacuum Operation…………………………………………………………………….……

Blowing Operation……………………………………………………………………………….….

Maintenance…………………………………………………………………………………………

Installing & Cleaning Cartridge Filter……………………………...………………..….…………

Installing & Cleaning Foam Sleeve Filter………………………...………………….…..….……

Resetting the Remote Control…………………………………………………………………….

Troubleshooting……………………………………………………………………………………..

Exploded View and Parts List……………………..………………………………………………

IMPORTANT SAFETY INSTRUCTIONS

Read and understand all instructions before using this vacuum

Read and understand this owner’s manual and all labels on the Wet/Dry Vacuum cleaner before operating.

Safety is a combination of common sense, staying alert and knowing how your vacuum works. Use this

Wet/Dry Vac only as described in this manual. To reduce the risk of personal injury or damage to your

Wet/Dry Vac, use only Vacmaster®recommended accessories.

For Household Use Only.

SAVE THIS MANUAL FOR FUTURE REFERENCE.

WARNING:TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

• Do not run vac unattended.

• Do not vacuum, or use this Wet/Dry Vac near flammable liquids, gases, or explosive vapors like gasoline

or other fuels, lighter fluids, cleaners, oil-based paints, natural gas, hydrogen, or explosive dusts like coal

dust, magnesium dust, grain dust, or gun power. Sparks inside the motor can ignite flammable vapors or

dust.

• Do not vacuum anything that is burning or smoking, such as cigarettes, matches, or hot ashes.

• Keep cord away from heated surfaces.

• Do not expose to rain. Store indoors.

• Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

• Do not use with damaged cord, plug or other parts.

• If your Wet/Dry Vac is not working as it should, has missing parts, has been dropped or damaged, left

outdoors or dropped into water, return it to an independent service center.

• Do not pull or carry by cord, use cord as handle, close a door on cord, or pull cord around sharp edges or

corners.

• Do not run Wet/Dry Vac over cord.

• Do not handle plug or the Wet/Dry Vac with wet hands.

• To reduce the risk of health hazards from vapors or dusts, do not vacuum toxic materials.

• Do not use or store near hazardous materials.

• Do not use this Wet/Dry Vac with a torn filter or without the filter installed except when vacuuming liquids

as described in the operation section of this manual.

• Do not allow to be used as a toy. Close attention is necessary when used by or near children.

• To reduce the risk of injury from accidental starting, unplug power cord before changing or cleaning filter.

• Do not leave Wet/Dry Vac unattended when plugged in. Unplug from outlet when not in use and before

servicing.

•Turn off Wet/Dry Vac before unplugging.

• Do not put any object into ventilation openings. Do not vacuum with any ventilation openings blocked;

keep free of dust, lint, hair or anything that may reduce air flow.

• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.

• To reduce the risk of falls, use extra care when cleaning on stairs.

When using as blower:

• Direct air discharge only at work area.

• Do not use Wet/Dry Vac as a sprayer.

• Do not direct air at bystanders.

• Keep children away when blowing.

• Wear safety goggles.

SAFETY INSTRUCTIONS & WARNINGS

This Wet/Dry Vac is double-insulated, eliminating the need for a separate grounding system. Use only

identical replacements parts. Read the instructions for Servicing Double-Insulated Wet/Dry Vacs before

servicing. Use this Wet/Dry Vac as described in this manual.

Observe the following warnings that appear on the motor housing of your Wet/Dry Vac.

DOUBLE INSULATED - GROUNDING NOT REQUIRED - WHEN SERVICING USE ONLY

IDENTICAL REPLACEMENT PARTS.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK-DO NOT EXPOSE TO RAIN. STORE

INDOORS.

WARNING: FOR YOUR OWN SAFETY, READ AND UNDERSTAND OPERATOR’S MANUAL. DO

NOT RUN UNATTENDED. DO NOT PICK UP HOT ASHES, COALS, TOXIC, FLAMMABLE OR OTHER

HAZARDOUS MATERIALS, DO NOT USE AROUND EXPLOSIVE LIQUIDS OR VAPORS.

CAUTION:

• Do not vacuum drywall dust or fireplace soot or ash with standard Wet/Dry filter. This is very fine dust

which will not be captured by the filter and may cause damage to motor. When vacuuming fine dust use a

fine dust filter (sold separately).

WARNING: SERVICING OF DOUBLE-INSULATED WET/DRY VACUUMM

WITH A DOUBLE-INSULATED WET/DRY VACUUM, TWO SYSTEMS OF INSULATION ARE PROVIDED

INSTEAD OF GROUNDING. NO GROUNDING MEANS IS PROVIDED ON A DOUBLE-INSULATED

APPLIANCE, NOR SHOULD A MEANS FOR GROUNDING BE ADDED. SERVICING A DOUBLE

INSULATED WET/DRY VACUUM REQUIRES EXTREME CARE AND KNOWLEDGE OF THE SYSTEM,

AND SHOULD BE DONE ONLY BY QUALIFIED SERVICE PERSONNEL. REPLACEMENT PARTS FOR

A DOUBLE-INSULATED WET/DRY VACUUM MUST BE IDENTICAL TO THE PARTS THEY REPLACE.

YOUR DOUBLE-INSULATED WET/DRY VAC IS MARKED WITH THE WORDS ‘DOUBLE INSULATED’

AND THE SYMBOL (SQUARE WITHIN A SQUARE) MAY ALSO BE MARKED ON THE

APPLIANCE.

• DO NOT use without filters in place.

CAUTION: TO REDUCE THE RISK OF INJURY FROM MOVING PARTS- UNPLUG BEFORE

SERVICING.

When using an extension cord with your Wet/Dry Vac refer to the following table to determine the required

A.W.G. wire size. Before using the cleaner make sure the power cord and extension cord are in good

working conditions. Make repairs or replacements before using the vacuum cleaner. Only use extension

cords that are rated for outdoor use.

Length of Extension Cord

110V-120V

25 Feet 7.5

Meter

50 Feet 15.25

Meters

100 Feet 30.5

Meters

150 Feet 45.7

Meters

Amps A.W.G Wire Size

0-6 18 16 16 14

7-10 18 16 14 12

11-12 16 16 14 12

13-16 14 12 Not recommended

DOUBLE INSULATION INSTRUCTIONS

EXTENSION CORDS

UNPACKING AND CHECKING CARTON CONTENTS

QTY

Key Description………………...

A Vac Assembly………….......

B Hose Holding Rod ………..

C Mounting Rack …………….

D 11-Foot Hose……………….

E 10-Foot Flex Hose…………

F Floor / Squeegee Nozzle….

G Crevice Tool ……………….

H Round Dusting Brush ……..

I Extension Wands ……........

J Car Nozzle …………………

K Cartridge Filter……………..

L Filter Retainer………………

M Air/Noise Diffuser ………...

N Side Tool Caddy..…………

O Remote Control Handle.….

P Foam Filter………………..

Q Screws………………………

R Operator’s Manual…………

NOTE: The hose and accessories for this vacuum

are 1 7/8” diameter.

Remove entire contents of carton. Check

each item a

ainst the carton contents list.

Carton contents lists

WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS

DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC

UNPACKING YOUR WET/DRY VACUUM & GENERAL ASSEMBLY

1. Verify that the power cord is disconnected from the outlet. (fig. 1)

2. Undo the latches. (fig. 2)

3. Lift the power head off of the container. (fig. 3)

4. Remove the contents from inside the container, make sure you have all contents as listed on page 5.

(fig. 4)

5. Replace the power head to the container and insert the noise diffuser into the blowing port. (fig. 5)

MOUNTING RACK AND STORAGE ASSEMBLY

IMPORTANT!

•Do not mount the rack over 5 feet from the floor.

•Do not screw the rack to drywall only. Secure the screws to a stud.

GENERAL ASSEMBLY INSTRUCTIONS

•Do not hang from or sit on the mounting rack

•Do not exceed 40 pounds of maximum weight limit.

6. Insert the hose holding rod into the two holes located on the top of the mounting rack. Make sure the

bend of the rod is directed away from the wall. (fig. 6)

7. Select a location on a wall stud that is not more than 20 feet away from an electrical outlet.

8. Align the three screw holes so that they are over a stud. Make sure the rack is level and mark the whole

locations. Make a 1/8-inch diameter pilot hole in each marked location. Secure the mounting rack to the

wall stud with the three screws provided. (fig. 7)

MOUNTING THE VACUUM ON TO THE RACK

1. Measure the distance from the top screw hole of the mounting rack to the closest electrical outlet and

add 12 inches. This is the amount of cord needed; wind the excess power cord around the cord wrap

area located on the rear of the vacuum. (fig. 8)

2. Make sure the code is not winded to A. (fig.9)

3. Mount the vacuum onto the mounting rack by aligning the vac hanging hook (A) with slot (B) on the

mounting rack and slide downward until it locks. When trying to mount vac onto the rack , please hold the

plug and make sure the cable is not hanging between rack and the back of the vac to be clamped . (fig.

10)

4. Attach the tool caddy on either side of the vac onto the hooks provided. (fig.11)

5. Your vacuum comes ready for dry vacuum cleaning. If the cartridge filter is not installed refer to page

11 for filter installation.（fig. 12 & 13）

6. For wet vacuum cleaning, install the supplied foam filter. (fig. 14) See page 11 for filter installation.

7. Place the power head back on the container, and secure into place using the 2 side latches. (fig. 15 & 16)

8. Insert the locking end of the hose into the port of the container and lock in to place. (fig. 17)

9. Choose the desired accessories and push onto the suction tube. (fig. 18)

POLARIZED PLUG

To reduce the risk of electrical shock, this appliance has a polarized plug (one with the blade wider than the

other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse

the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the

plug in any way. Double insulation eliminates the need for the three wire grounded power cord and

grounded power supply system.

DISMOUNTING THE VACUUM FROM THE RACK

1. Disconnect the power cord form the electrical outlet. (fig. 1)

2. Press the release lever with your left hand. (fig. 2)

3. Lift the vacuum up and out of the rack by the handle with your right hand. (fig. 3)

DRY VACUUMING

WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED

‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES,

VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT

ARE NOT LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,

ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;

COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS

FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.

1. Verify that the power cord is disconnected from the outlet. (fig. 1)

2. In order to prepare your vacuum for dry vacuuming, verify that the cartridge filter is securely mounted.

Make sure the filter is pushed in until it stops against the power head. (fig. 2) (Your Wet/Dry Vac comes

with the cartridge filter pre-installed, if not see page 11 for installation instructions.)

3. Place filter retainer on top of cartridge filter and tighten down by turning the retainer handle clockwise.

(fig. 3)

4. Place the power head back on the container, aligning the top section with the latches, and snap into

place. (fig. 4)

OPERATING INSTRUCTIONS: DRY VACUUMING

5. Insert the locking end of the hose into the vacuum port on the power head and lock in place. Push the

required attachment onto the free end of the hose or extension. (fig. 5)

6. Plug in the power cord into the outlet and hang the vacuum onto the rack or use off the rack . (fig. 6)

7. Turn the motor on by flipping the switch to the ‘I’ ON position. (fig. 7) For remote control use, set the

power switch to remote control position “ ” and turn the vacuum on by pressing the ‘I’ ON

button on the remote control handle for at least one second. (fig. 8 & 9)

8. Once you have completed vacuuming, flip the switch to the ‘O’ OFF position or press the ‘O’ OFF button

on the remote control for at least one second.

O = OFF I = ON = Remote Control

DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.

ACUUM OPERATION

LIQUID VACUUMING

WARNING: BE SURE TO READ, UNDERSTAND, AND APPLY INFORMATION, ENTITLED

‘SAFETY INSTRUCTIONS & WARNINGS’. DO NOT VACUUM IN AREAS WITH FLAMMABLE GASES,

VAPORS, OR EXPLOSIVE DUSTS IN THE AIR. FLAMMABLE GASES OR VAPORS INCLUDE BUT

ARE NOT LIMITED TO; LIGHTER FLUID, SOLVENT TYPE CLEANERS, OIL-BASE PAINTS, GASOLINE,

ALCOHOL OR AEROSOL SPRAYS. EXPLOSIVE DUSTS INCLUDE BUT ARE NOT LIMITED TO;

COAL, MAGNESIUM, GRAIN OR GUN POWDER. TO REDUCE THE RISK OF HEALTH HAZARDS

FROM VAPORS OR DUST, DO NOT VACUUM TOXIC MATERIALS.

WARNING: DO NOT PLUG IN POWER CORD TO POWER OUTLET, MAKE SURE PLUG IS

DISCONNECTED BEFORE ASSEMBLING THE WET/DRY VAC

IMPORTANT! When vacuuming large quantities of liquids, we recommend that you remove the vacuum

from the mounting rack and put it on the floor. The vacuum can be heavy when full of liquids and may be

difficult to remove from the rack.

1. Verify that the power cord is disconnected from the outlet. Verify that the container is clean and free of

dust and dirt. (fig. 1)

2. Remove cartridge filter, then carefully install the foam sleeve filter over the filter cage and place the

power head back on the container. (fig. 2) See filter installing instructions on page 11.

DO NOT USE THE CARTRIDGE FILTER FOR LIQUID VACUUMING.

OPERATING INSTRUCTIONS – WET VACUUMING

3. Fit the desired nozzle to the vacuum hose. (fig. 3)

4. Verify that the switch is in the ‘O’ OFF position before plugging the power cord into the outlet. (fig. 4)

5. For large amounts of liquid vacuuming, it is recommended to place the vacuum on the floor. Turn the

motor on by flipping the switch on the power head to the ‘I’ ON position or flip the switch to the Remote

Control Position and use the ‘I’ ON button on the remote control. (fig. 5 & 6)

6. After wet vacuuming, turn the machine off and remove plug from power supply. To prevent the risk of

possible mildew, empty the container, clean and dry the inside and outside of the container, and remove the

foam filter and allow to air dry before storage.

IMPORTANT! When vacuuming large quantities of liquids, do not immerse the nozzle completely in the

liquid; leave a gap at the tip of the nozzle opening to allow air inflow. The machine is fitted with a float valve

that stops the suction action when the container reaches its maximum capacity. You will notice an increase

in motor speed. When this happens, turn off the machine, disconnect from power supply, and empty the

liquid into a suitable receptacle or drain. To continue vacuuming, refit the power head to the container. After

wet vacuuming, turn the machine off and remove plug from power supply. To prevent the risk of possible

mildew, empty the container, clean and dry the inside and outside of the container, and remove the foam

filter and allow to air dry before storage.

UID

ACUUM OPERATION

CAUTION: DO NOT SUBMERGER THE REMOTE CONTROL INTO LI

UIDS

REMEMBER! The foam filter must be removed after wet vacuuming, and a cartridge filter must be

installed before dry vacuuming again.

This Wet/Dry Vac has blowing capabilities. To use the blower feature follow the instructions listed.

WARNING: ALWAYS WEAR SAFETY GOGGLES COMPLYING WITH ANSI Z87.1 (OR IN

CANADA, CSAZ94.3) BEFORE USING BLOWER.

WARNING: KEEP BYSTANDERS CLEAR FROM BLOWING DEBRIS.

WARNING: WEAR A DUST MASK IF BLOWING CREATES DUST THAT MIGHT BE INHALED.

1. Verify that the power cord is disconnected from the outlet. (fig. 1)

2. Make sure the container is empty before using as a blower.

3. Remove the noise diffuser from the blower port. (fig. 2)

4. Remove hose from the vacuum port and insert the locking end of the hose into the blowing port on the

power head and lock into position. (fig. 3)

5. Fit the desired extension wand and or nozzle to the free end of the vacuum hose. (fig. 4)

6. Ensure the power switch is turned off and plug in the power supply. (fig. 5)

7. Before turning ON the vac, firmly hold loose end of the hose. Turn the motor on by flipping the switch to

the ‘I’ ON position or use the vac with switch set to remote control setting and the remote control. (fig. 6)

1. Verify that the power cord is disconnected from the outlet. (fig. 1)

2. Disconnect the hose from the vacuum. (fig. 2)

3. Remove the vacuum from the mounting rack.

4. Undo the latches and remove the power head from the container. (fig. 3)

5. Clear all dirt or debris from the container and hose. (fig. 4)

6. Clean the foam filter by washing it with water and mild soap. (fig. 5)

7. Check the hose, attachments, and power cord to verify that they have not been damaged.

MAINTENANCE

BLOWING OPERATION

Andere Handbücher für VWM510

Inhaltsverzeichnis

Andere Vacmaster Staubsauger Handbücher

Vacmaster

Vacmaster VOA407S Bedienungsanleitung

Vacmaster

Vacmaster VJ206H Bedienungsanleitung

Vacmaster

Vacmaster VQ407S-A Bedienungsanleitung

Vacmaster

Vacmaster VOC507S 1001 Bedienungsanleitung

Vacmaster

Vacmaster VJH1211PF 0203 Bedienungsanleitung

Vacmaster

Vacmaster PROFESSIONAL VJF608PF 0202 Bedienungsanleitung

Vacmaster

Vacmaster VJS1211 Bedienungsanleitung

Vacmaster

Vacmaster VH105 Bedienungsanleitung

Vacmaster

Vacmaster VF408 Bedienungsanleitung

Vacmaster

Vacmaster VQ1220PF Bedienungsanleitung

Vacmaster

Vacmaster UC0101 Bedienungsanleitung

Vacmaster

Vacmaster VOC507S Bedienungsanleitung

Vacmaster

Vacmaster VJC507P Bedienungsanleitung

Vacmaster

Vacmaster VJC1210PF Bedienungsanleitung

Vacmaster

Vacmaster VJE1412SW 0202 Bedienungsanleitung

Vacmaster

Vacmaster EAT718S Bedienungsanleitung

Vacmaster

Vacmaster VFB511B 0202 Bedienungsanleitung

Vacmaster

Vacmaster VOM205P Bedienungsanleitung

Vacmaster

Vacmaster VBV809PF Bedienungsanleitung

Vacmaster

Vacmaster VJH1612PF 0202 Bedienungsanleitung

Vacmaster

Vacmaster VDK1138SWC-110 Bedienungsanleitung

Vacmaster

Vacmaster DVTB2015 Bedienungsanleitung

Vacmaster

Vacmaster VQ1530SFDC Bedienungsanleitung

Vacmaster

Vacmaster VOM205P Bedienungsanleitung

Beliebte Staubsauger Handbücher anderer Marken

Bissell

Bissell LittleGreen Proheat 1425 Series Bedienungsanleitung

Panasonic

Panasonic MC-YL637S147-AE Bedienungsanleitung

NEFF

NEFF N17XH10 0 Series Bedienungsanleitung

LG A9 Series Bedienungsanleitung

Oreck

Oreck Cordless Captura BK51700 Series Bedienungsanleitung

Kogan

Kogan KAVACROBVWA Bedienungsanleitung

Kränzle

Kränzle VENTOS 50 ID Benutzerhandbuch

EVVO

EVVO Ai35 Bedienungsanleitung

DeWalt

DeWalt DWH200D Bedienungsanleitung

Pontec

Pontec Pondomatic Vacuum Cleaner Bedienungsanleitung

Cleanmaxx

Cleanmaxx PC-P007E Bedienungsanleitung

Exido

Exido 240-114 Bedienungsanleitung

RIDGID

RIDGID WD1685AU0 Bedienungsanleitung

Ezviz

Ezviz RE4P Bedienungsanleitung

STG global

STG global TANVAC HDV3000 Bedienungsanleitung

Shark

Shark ROTATOR PRO COMPLETE NV550 Series Bedienungsanleitung

Factory

Factory M3340 Bedienungsanleitung

Shop-Vac

Shop-Vac VN92 SERIES Bedienungsanleitung