VarTech Systems VTPC2100VS Bedienungsanleitung

Solutions for Demanding Applications

VARTECH

S Y S T E M S I N C.

21.5” Wide Format Class 1 - Division 2 Certified

VESA Mount Enclosed PC

Model VTPC2100VS / VTPC2100VS Video Monitor

User’s Guide

Read these instructions completely before attempting to operate your new VESA Mount PC

Revision History

Date Rev No Summary Page

12/04/17 00 First Issue

Safety Instructions

PLEASE NOTE - This equipment is suitable for use in Class I, Division 2 or non-hazardous

locations only.

WARNING - EXPLOSION HAZARD - DO NOT DISCONNECT EQUIPMENT UNLESS POWER HAS

BEEN SWITCHED OFF OR THE AREA IS KNOWN TO BE NON-HAZARDOUS.

AVERTISSEMENT - RISQE D'EXPLOSION - AVANT DE DECONNECTER L'EQUIPMENT, COUPER

LE COURANT OU S'ASSURER QUE L'EMPLACEMENT EST DESIGNE NON DANGEREUX.

Read the Safety Instructions carefully and keep it for use later.

The chassis metalwork of the module must be installed properly to the main earthing termination

for Class 1 equipment.

Care must be exercised in the application of the system to prevent overheating. Ensure that the

ambient temperature around the system does not exceed 60°C and provide adequate means of

ventilation to achieve this.

When cleaning cut off the electrical supply at all times. Never use liquid or aerosol detergent,

use a soft damp cloth instead.

To avoid electric shock, never touch the inside of the system. There are no user adjustable

components inside, only a qualified technician should open the system’s case.

If the system does not operate normally – in particular, if there are any unusual sounds or smells

coming from it – disconnect it immediately.

Do not put pressure on the LCD panel screen because it is very fragile.

Always handle the system with care when moving it.

Take care that the system is disposed of correctly at the end of its life. If in doubt refer to your

local ordinances or regulations for proper disposal.

User to supply appropriate lockable type plug and power disconnecting switch.

The end user must either supply a switch to their power outlet suitable for Class 1, Division 2

use (if adjacent to the power outlet), or locate the said switch outside the hazardous area.

This equipment is suitable for use in a Class 1, Division 2, Groups A, B, C, and D or non-

hazardous location only.

Explosion Hazard - Substitution of components may impair suitability for hazardous locations.

Any Equipment or associated cabling connected to this device must be non-incendive and/or

suitable for the Class 1, Division 2 area in which it is to be installed.

Hazardous Locations:

This equipment is suitable only for the locations specified on the product nameplate, specifically:

Class I, Division 2 Groups A, B, C, D

Non-hazardous locations

The following statement applies to use in hazardous locations:

WARNING! Explosion Hazard

Substitution of components may impair suitability for hazardous locations.

Do not disconnect equipment unless power has been switched off and area is

known to be non-hazardous.

Do not connect or disconnect components unless power has been switched off.

All wiring must comply with NEC 2014 articles are 501.10(B), 502.10(B), and

503.10(B) as appropriate.

Peripheral equipment must be suitable for the location in which it is used.

This equipment has an operating temperature code of T4 when operating in a

60`C (140`F) ambient environment. Do not install this product in environments

where atmospheric gases have an ignition temperature of less than 135`C

(275`F).

Environment and Enclosure Information:

Review this information on enclosures before installing the product:

ATTENTION: Environment and Enclosure

This equipment is intended for use in a Pollution Class 2 industrial environment, in

overvoltage Category II applications (as defined in IEC publication 60664-1), at

altitudes up to 2000 meters (6561 feet).

See NEMA Standards publication 250 and IEC publication 60529, as applicable,

for explanations of the degrees of protection provided by different types of

enclosures. The user may also reference the Industrial Automation Wiring and

Grounding Guidelines, publication 1770-4.1, for additional installation

requirements pertaining to this equipment.

Cleaning the LCD monitor

To clean the LCD panel:

Wipe the screen gently with a clean lens brush made of camel hair, or a soft, clean, lint free

cloth. This is to remove dust and other particles without scratching the LCD panel.

If it is still not clean, then wipe with a damp lint free cloth and blow on it to dry.

Do not clean the panel with a keton-type material (e.g. acetone), or ethyl toluene, ethyl acid, methyl

or chloride. These may damage the LCD panel.

Do not apply pressure to the LCD panel.

Standard Technical Specifications:

LCD Monitor:

Size / Type 21.5” 1080P Full HD TFT LCD

Native Resolution 1920 x 1080

Contrast Ratio 5000:1

Viewing Angles Horizontal: 178°

Vertical: 178°

Pixel Pitch 248.25mm x 248.25mm

Brightness (typical) 300 cd/m²

Response Time (typical) 25ms GTG(Avg. Typ.)

Colors Supported 16.7 million

Computer System:

Processor 2.0GHz Quad Core Intel® Celeron® Processor J1900

System Memory 4GB DDR3L-1333 SO-DIMM x 1

BIOS AMI

Hard Drive 500 GB SATA

Operating System Windows 10 - 32 bit

I/O Ports 2 x LAN

3 x RS-232

1 x RS-422/485

2 x USB 2.0

1 x Power Connector

Graphics

Intel® HD Graphics

LAN 2 x 10/100/1000Mbs support Wake-on-LAN

Touch Screen Resistive Touch

Touch Screen Interface USB

Power & Operational Specifications:

Power Input 100 - 220 VAC 1.5A

Power Consumption 60W

Temperature Operational: -32°F to 122°F 0°C to 50°C

Storage: -4°F to 140°F -20°C to 60°C

Humidity Operational: 20 to 40°C, 90% RH NC

Storage: 5 to 65°C, 28% RH NC

Installation of Your VESA Mount PC

Packaged with each carton will be:

1 – VTPC2100VS

1 - Users Guide (Printed or on CD/Flash Drive)

BEFORE MAKING ANY CONNECTIONS OR APPLYING POWER,

FIRST READ THROUGH THE ENTIRE MANUAL

Mounting Procedure

VESA Panel Mounting Procedure:

1- Install the enclosure to a 100mm VESA mount pedestal.

2- Secure the enclosure using the screws and lock washers, supplied with the unit.

VESA Mount Drawing: Detail –A–

Connections to the VESA Mount PC

Bottom Rear View

-Connector Panel-

Andere VarTech Systems Monitor Handbücher

VarTech Systems

VarTech Systems VT14A-D Bedienungsanleitung

VarTech Systems

VarTech Systems VT320D Bedienungsanleitung

VarTech Systems

VarTech Systems VT14B-C1 Bedienungsanleitung

VarTech Systems

VarTech Systems VT420W Bedienungsanleitung

VarTech Systems

VarTech Systems VT29B-M Bedienungsanleitung

VarTech Systems

VarTech Systems VT121XA4 Bedienungsanleitung

VarTech Systems

VarTech Systems VT084XHB Bedienungsanleitung

VarTech Systems

VarTech Systems VT121CC Bedienungsanleitung

VarTech Systems

VarTech Systems VT181CH Bedienungsanleitung

VarTech Systems

VarTech Systems DiamondVue VT201C Bedienungsanleitung

VarTech Systems

VarTech Systems DiamondVue VT190C Bedienungsanleitung

VarTech Systems

VarTech Systems VT20A Bedienungsanleitung

VarTech Systems

VarTech Systems VT150CHB Bedienungsanleitung

VarTech Systems

VarTech Systems VT213C Bedienungsanleitung

VarTech Systems

VarTech Systems VT170W Bedienungsanleitung

VarTech Systems

VarTech Systems DiamondVue VT150P Bedienungsanleitung

VarTech Systems

VarTech Systems VT181R2 Bedienungsanleitung

VarTech Systems

VarTech Systems VT420 Series Bedienungsanleitung

VarTech Systems

VarTech Systems VT190PVS Bedienungsanleitung

VarTech Systems

VarTech Systems DiamondVue VT084C Bedienungsanleitung

VarTech Systems

VarTech Systems VT201CM Bedienungsanleitung

VarTech Systems

VarTech Systems VTPC150XPE Bedienungsanleitung

VarTech Systems

VarTech Systems VT084XA4 Bedienungsanleitung

VarTech Systems

VarTech Systems VT19B-PW Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung