Weider 9000 Bench Bedienungsanleitung

QUESTIONS?

As a manufacturer, we are com-

mitted to providing complete

customer satisfaction. If you

have questions, or if there are

missing or damaged parts,

please call:

08457 089 009

Or write:

ICON Health & Fitness, Ltd.

Unit 4

Revie Road Industrial Estate

Revie Road

Beeston

Leeds

LS11 8JG

[email protected]

Model No. WEEMBE39221

Serial No.

Write the serial number in the

space above for reference.

CAUTION

Read all precautions and instruc-

tions in this manual before

using this equipment. Save this

manual for future reference.

Serial Number Decal (under seat)

USER’S MANUAL

www.iconeurope.com

Visit our website at

WARNING DECAL PLACEMENT

WARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

WEIGHT RESISTANCE CHART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19

CABLE DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20

TROUBLESHOOTING AND MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

EXERCISE GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: A PART IDENTIFICATION CHART and a PART LIST/EXPLODED DRAWING is attached in the centre of

this manual. Remove the PART IDENTIFICATION CHART and PART LIST/EXPLODED DRAWING before begin-

ning assembly.

TABLE OF CONTENTS

The decals shown here have been placed on

the weight bench. If a decal is missing or

illegible, call our Customer Service

Department to order a free replacement decal

(see the back cover of this manual). Apply the

replacement decal in the location shown.

Keep hands and

fingers clear of

this area.

1. Read all instructions in this manual before

using the weight bench. Use the weight

bench only as described in this manual.

2. It is the responsibility of the owner to ensure

that all users of the weight bench are ade-

quately informed of all precautions.

3. The weight bench is intended for home use

only. Do not use the weight bench in any

commercial, rental, or institutional setting.

4. Use the weight bench only on a level surface.

Cover the floor beneath the weight bench to

protect the floor.

5. Make sure all parts are properly tightened

each time you use the weight bench. Replace

any worn parts immediately.

6. Keep children under 12 and pets away from

the weight bench at all times.

7. Keep hands and feet away from moving parts.

8. Always wear athletic shoes for foot protec-

tion whilst exercising.

9. Always move the bench out of the way when

performing squat exercises. Always discon-

nect the lat bar from the high pulley station

when performing an exercise that does not

require it.

10. Always set both weight rests and both safety

spotters at the same height.

11. The weight bench is designed to support a

maximum user weight of 115 kg (250 lbs.).

12. Do not place more than 136 kg (300 lbs.),

including the barbell, on the weight rests. Do

not place more than 68 kg (150 lbs.) on the

weight carriage or leg lever. Note: The weight

bench is designed to be used with an Olympic

barbell, and standard or Olympic weights. The

weight bench does not include a barbell or

weights.

13. Always place an equal amount of weight on

each side of the weight carriage or barbell.

14. Always secure the weights with the weight

pins when they are mounted on the weight

carriage.

15.

Always exercise with a partner. Your partner

should be ready to catch the barbell if you

cannot complete a repetition.

16. Make sure that the cables remain on the pul-

leys at all times. If the cables bind as you are

exercising, stop immediately and make sure

that the cables are on the pulleys.

17. If you feel pain or dizziness at any time

whilst exercising, stop immediately and

begin cooling down.

WARNING:Before beginning this or any exercise program, consult your physician. This

is especially important for persons over the age of 35 or persons with pre-existing health problems.

Read all instructions before using. ICON assumes no responsibility for personal injury or property

damage sustained by or through the use of this product.

WARNING: To reduce the risk of serious injury, read the following important precautions

before using the weight bench.

IMPORTANT PRECAUTIONS

Weight Carriage

Butterfly Arm

Safety Spotter

Weight Rest

Lat Bar

Weight Tube

Backrest Frame

Right Side

Left Side

Note: The terms “right side” and “left side” are determined relative to a person sitting on the

bench; they do not correspond to right and left on the drawings in the manual.

Curl Pad

Backrest

Low Pulley Station

High Pulley Station

Storage Tube

Foot Plate

Leg Lever

Seat

BEFORE YOU BEGIN

Thank you for selecting the versatile WEIDER®9000

weight bench. The WEIDER®9000 weight bench offers

a selection of weight stations designed to develop

every major muscle group of the body. Whether your

goal is to tone your body, build dramatic muscle size

and strength, or improve your cardiovascular system,

the WEIDER®9000 weight bench will help you to

achieve the specific results you want.

For your benefit, read this manual carefully before

using the weight bench. If you have questions,

please call our Customer Service Department at 08457

089 009. To help us assist you, please note the prod-

uct model number and serial number before calling.

The model number is WEEMBE39221. The serial

number can be found on a decal attached to the

weight bench (see the front cover of this manual for

the location).

Before reading further, please review the drawing

below and familiarise yourself with the parts that are

labelled.

ASSEMBLED

DIMENSIONS:

Height: 218 cm (86.0 in.)

Width: 123 cm (48.5 in.)

Depth: 220 cm (86.5 in.)

Before beginning assembly, carefully read the

following information and instructions:

•Assembly requires two people.

•Place all parts in a cleared area and remove the

packing materials. Do not dispose of the packing

materials until assembly is completed.

•Tighten all parts as you assemble them, unless

instructed to do otherwise.

•As you assemble the weight bench, make sure all

parts are oriented as shown in the drawings.

•For help identifying small parts, use the PART

IDENTIFICATION CHART in the centre of this

manual.

The following tools (not included) are required

for assembly:

• Two adjustable spanners

• One rubber mallet

• One standard screwdriver

• One Phillips screwdriver

• Lubricant, such as grease or petroleum jelly,

and soapy water.

Assembly will be more convenient if you have a

socket set, a set of open-end or closed-end

wrenches, or a set of ratchet spanners.

Make Things Easier for Yourself

Everything in this manual is designed to ensure

that the weight bench can be assembled suc-

cessfully by anyone. However, it is important to

realize that the versatile weight bench has many

parts and that the assembly process will take

time. Most people find that by setting aside plen-

ty of time, assembly will go smoothly.

ASSEMBLY

Press a 50mm Square Inner Cap (43) into the

end of the Right Base (1).

Insert an M10 x 60mm Carriage Bolt (50) up

through the bottom of the Right Base (1). Lay the

Base on the floor.

Repeat this step with the Left Base (2).

Before beginning assembly, be sure that

you have read and understand the infor-

mation in the box above.

Rack Assembly

3. Attach the Foot Plate (9) and the Rear Upright (6)

to the Right and Left Bases (1, 2) with two M10 x

68mm Bolts (46) and two M10 Nylon Locknuts

(49).

Attach the Foot Plate (9) to the Centre Upright (5)

with an M10 x 68mm Bolt (46), an M10 Washer

(52), and an M10 Nylon Locknut (49).

Do not tighten the M10 Nylon Locknuts (49)

yet.

2. Slide the Centre Upright (5) onto the M10 x

60mm Carriage Bolts (50) in the Right and Left

Bases (1, 2). Make sure that the Centre Upright

is turned so the indicated bracket is on the

side shown. Hand tighten two M10 Nylon

Locknuts (49) onto the Bolts. Do not tighten the

Nylon Locknuts yet.

150

Bracket

5. Press a 50mm Square Inner Cap (43) into the top

of the right Upright (3).

Slide a Safety Spotter (15) onto the right Upright

(3) and engage the Knob (17) into the lowest

adjustment hole in the Upright. Turn the Knob

clockwise until it is tight.

Slide a Weight Rest (16) onto the right Upright (3)

and engage the Knob (17) into an adjustment hole

in the Upright. Turn the Knob clockwise until it is

tight.

Repeat this step with the left Upright (not

shown).

6. Attach the Crossbar (7), with the decal on the

side shown, to the right Upright (3) with four M10

x 68mm Bolts (46), two Support Plates (14), and

four M10 Nylon Locknuts (49). Do not tighten

the Nylon Locknuts yet.

Attach the Crossbar (7) to the left Upright (not

shown) in the same manner.

4. Attach one of the Uprights (3) to the Right Base

(1) with four M10 x 68mm Bolts (46), two Support

Plates (14), and four M10 Nylon Locknuts (49).

Do not tighten the Nylon Locknuts yet.

Repeat this step with the other Upright (not

shown) and the Left Base (not shown).

Decal

Adjustment

Holes

7. Slide the Carriage Stop (19) onto the Rear

Upright (6). Make sure that the Carriage Stop is

oriented so the Carriage Stop Bushing (20)

and the indicated hole are in the positions

shown. Attach the Carriage Stop to the hole near

the bottom of the Rear Upright with an M8 x

70mm Bolt (58) and an M8 Nylon Locknut (48).

Press two 25mm Round Inner Caps (45) into the

tube on the Weight Carriage (10). Insert an M10 x

19mm Bolt (61) into the bracket on the Weight

Carriage. Slide the Weight Carriage onto the Rear

Upright (6). Be sure the bracket is on the side

shown.

9. Attach the Top Frame (8) to the Crossbar (7) with

two M10 x 68mm Bolts (46), two M10 Washers

(52), and two M10 Nylon Locknuts (49).

Attach the Top Frame (8) to the Centre Upright

(5) with two M10 x 68mm Bolts (46), two M10

Washers (52) and two M10 Nylon Locknuts (49).

Do not tighten the M10 Nylon Locknuts (49)

yet.

10. Attach the Top Frame (8) to the Rear Upright (6)

with three M10 x 68mm Bolts (46), two Support

Plates (14), and three M10 Nylon Locknuts (49).

Tighten the M10 Nylon Locknuts (49) used in

steps 2–10.

8. Press three 50mm Square Inner Caps (43) into

the indicated ends of the Top Frame (8).

745

Hole

49 49

11. Identify the Right and Left Butterfly Arms (11, 12)

by noting the positions of the welded brackets.

Press two 45mm Square Inner Caps (42) into the

ends of the Left Butterfly Arm (12). Wet the bot-

tom end of the Butterfly Arm with soapy water.

Slide a Large Foam Pad (18) onto the end of the

Butterfly Arm.

Lubricate the axles on the Top Frame (8) with

grease. Orient the Left Butterfly Arm (12) as

shown and slide it onto the left axle so that it is

behind the bracket on the Top Frame. Have a

second person secure the Butterfly Arm with two

1” Retainers (35) and a 1” Cover Cap (36). Note:

Place the Retainers on top of the included

retainer tool, as shown in the inset drawing.

Make sure the teeth on the Retainers bend

toward the tool. Gently tap the tool onto the

axle. Remove the tool, and tap the Cover Cap

onto the axle.

Repeat this step with the Right Butterfly Arm

(11).

12. Press a 25mm Round Inner Cap (45) into the

upper end of a Storage Tube (22), as shown.

Attach the Storage Tube (22) inside the hole in

the Right Base (1) with an M8 x 65mm Bolt (51),

two M8 Washers (53), two 13mm x 12mm

Spacers (38), and an M8 Nylon Locknut (48).

Repeat this step with the other Storage Tube

(not shown) and the Left Base (2).

13. Identify the Butterfly Cable (32), which has an

eyelet on each end. Attach one end of the Cable

to the bracket on the Left Butterfly Arm (12) with

an M8 x 22mm Shoulder Bolt (60) and an M8

Nylon Locknut (48).

11 8

Lubricate

Axle

Welded

Bracket

22 Hole

12 60

Bracket

Retainer

Tool

Axle

14. Wrap the Butterfly Cable (32) around a “V”-Pulley

(25). Attach the Pulley and a Large Cable Trap

(27) to the bracket on the Centre Upright (5) with

an M10 x 60mm Bolt (47) and an M10 Nylon

Locknut (49).

16. Wrap the Butterfly Cable (32) around a “V”-Pulley

(25). Attach the Pulley and a Large Cable Trap

(27) to the bracket on the Centre Upright (5) with

an M10 x 60mm Bolt (47) and an M10 Nylon

Locknut (49).

17. Attach the Butterfly Cable (32) to the bracket on

the Right Butterfly Arm (11) with an M8 x 22mm

Shoulder Bolt (60) and an M8 Nylon Locknut (48).

15. Remove the 90mm Pulleys (24) from the pre-

assembled Double “U”-Bracket (29).

Wrap the Butterfly Cable (32) under a 90mm

Pulley (24). Attach the Pulley to the Double “U”-

Bracket with an M10 x 45mm Bolt (57) and an

M10 Nylon Locknut (49).

Bracket

32 49

27 Bracket

Bracket

Andere Handbücher für 9000 Bench

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weider Heim-Fitnessstudio Handbücher

Weider

Weider 9015 Kurzanleitung

Weider

Weider 831.159822 Bedienungsanleitung

Weider

Weider WESY37530 Bedienungsanleitung

Weider

Weider WEBE09100 Bedienungsanleitung

Weider

Weider WESY16010 Bedienungsanleitung

Weider

Weider Pro 425 Bedienungsanleitung

Weider

Weider 8700 I Bedienungsanleitung

Weider

Weider 340 Lc Bench Benutzerhandbuch

Weider

Weider 8980 I Bedienungsanleitung

Weider

Weider Muscle 132w/ Bench Bedienungsanleitung

Weider

Weider Cross Bow By 1500x Bedienungsanleitung

Weider

Weider 330 Classic Bench Bedienungsanleitung

Weider

Weider WEBE4915.0 Bedienungsanleitung

Weider

Weider D120 Bedienungsanleitung

Weider

Weider 190 Tc Bench Bedienungs- und Wartungshandbuch

Weider

Weider Muscle 131wtw/ Bedienungsanleitung

Weider

Weider Easy Compact 90 Bedienungsanleitung

Weider

Weider Powerguide Home Gym Sy X2s Bedienungsanleitung

Weider

Weider Cts 2000 Club Series Bedienungsanleitung

Weider

Weider Master12 Position Bench Bedienungsanleitung

Weider

Weider Club 290 W Bench Bedienungsanleitung

Weider

Weider WESY47330 Bedienungsanleitung

Weider

Weider 200 Power Tower Bench Benutzerhandbuch

Weider

Weider Pro 400L Bedienungsanleitung

Beliebte Heim-Fitnessstudio Handbücher anderer Marken

Horizon Fitness

Horizon Fitness OXFORD 6 Bedienungsanleitung

Energetics

Energetics Multi Trainer 5.1 Bedienungsanleitung

Matrix

Matrix MG-PL Series Bedienungsanleitung

Reebok

Reebok Tbr2i Bedienungs- und Wartungshandbuch

Pure Fitness

Pure Fitness 8526HE Bedienungsanleitung

Bowflex

Bowflex Sport 001-6961 Bedienungsanleitung

NordicTrack

NordicTrack E8200 Competition Bench Kurzanleitung

Body Solid

Body Solid GHYP-345 Bedienungsanleitung

Evo

Evo TAHOE 5105 Bedienungsanleitung

cardiobull

cardiobull RA17 Bedienungsanleitung

ParaBody

ParaBody 40 Bedienungsanleitung

JLL

JLL Ventus Pro Air Power Bedienungsanleitung

Trojan

Trojan Colorado 370 Bedienungsanleitung

Octane Fitness

Octane Fitness xRide xR650 Bedienungsanleitung

Precor

Precor Discovery Series Bedienungsanleitung

Insportline

Insportline RW600 Bedienungsanleitung

Stamina

Stamina 55-1532 Bedienungsanleitung

Tunturi

Tunturi R25 Bedienungsanleitung