Weslo Cadence 78s Treadmill Bedienungsanleitung

ModetNo.831.295021

SeriaJNo.

WritetheseriaUnumberinthe

spaceaboveforfuturereference,

SeriaUNumber

DecaU

Assembly

Operation

Maintenance

Part List and Drawing

, ,CAUTION

Read aHprecautions and instrueo

tions in this manual before using

this equipment. Save this rnanuaJ

for future reference. Sears, Roebuck and Co., Roffman Estates, IL 60179

TABLE OF CONTENTS

iMPORTANT PRECAUTIONS ................................................................ 2

BEFORE YOU BEGIN ...................................................................... 4

ASSEMBLY .............................................................................. 5

OPERATION AND ADJUSTMENT ............................................................. 8

HOW TO FOLD AND MOVE THE TREADMILL ................................................. 11

MAINTENANCE AND TROUBLESHOOTING ................................................... 12

CONDiTiONiNG GUiDELiNES .............................................................. 14

ORDERING REPLACEMENT PARTS ................................................. Back Cover

FULL 90 DAY WARRANTY .......................................................... Back Cover

Note: An EXPLODED DRAWING and a PART LiST are attached in the center of this manual.

IMPORTANT PRECAUTIONS

WARNING: To educethedskofburne,f re,electricehook,oroju,topersons,read

the following important precautions and information before operating the tread mill.

1. it is the responsibility of the owner to ensure 10. When connecting the power cord (see page 8),

that all users of this treadmill are adequateJy pJug the power cord into a surge suppressor

informed of aH warnings and precautions. (not incJuded) and pJug the surge suppressor

2. Use the treadmill onJy as described.

3. Place the treadmill on a leveJ surface, with at

least eight feet of clearance behind it and two

feet on each side. Do not place the treadmill

on any surface that blocks air openings. To

protect the Hoot or carpet from damage,

place a mat under the treadmill

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of !2 and pets

away from the treadmiff at aH times.

7. The treadmill should not be used by persons

weighing more than 250 pounds.

8. Never affow more than one person on the

treadmill at a time.

9. Wear suitabJe exercise cJothee when using

the treadmill. Do not wear loose clothes that

could become caught in the treadmill.

AtHetic support clothes are recommended

for both men and women. Always wearathlet-

ic shoes. Never use the treadmill with bare

feet, wearing only stockings, or in sandals.

into a grounded circuit ca pabJe of carrying 15

or more amps. No other appliance shoutd be

on the same circuit. Do not use an extension

cord.

11. Use only a eingJe-outJet eurge suppressor that

meets aH of the specifications described on

page 8. To purchase a surge suppressor, see

your locaJ Sears store or call 1o800-366-7278

and order part number 146148, or see your

Jocal eJectronics store.

12. Failure to use a properly functioning surge

suppressor could reeuff in damage to the con-

troJ system of the treadmiff, ff the control sys-

tem is damaged, the walking belt may change

speed, accelerate, or stop unexpectedJy,

which may result in a fail and serious injury.

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or pJug is damaged, or if the

treadmill ie not working properly. (See page 4

if the treadmill is not working properJy.}

15. Never start the treadmill while you are stand-

ing on the walking belt. AJwaye hold the

16.The treadmHJ is capable of high speeds. 21. inspect and properly tighten all parts of the

Adjust the speed in small increments to treadmill regularly.

avoid sudden jumps in speed. 22. Never drop or insert any object into any

17. Never leave the treadmill unattended while it is opening.

running. Always remove the key and unplug _Lmn'_

the power cord when the treadmill is not in 23. uP_l_,_E}_: Always unplug the power

use. cord immediately after use, before cleaning

18. Do not attempt to raise, Iower_ or move the

treadmill until it is property assembled. ISee

ASSEMBLY on page 5, and HOW TO MOVE

THE TREADMmLL on page 11.) You must be

able to safely Hft 45 pounds (20 kg) to raise,

Jower, or move the treadmill.

the treadmill, and before performing the

maintenance and adjustment procedures

described in this manual Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorizedser-

vicerepresentative only.

19. Do not change the incline of the treadmill by

placing objects under the treadmill 24. This treadmill is intended for in=home use

20. When folding or moving the treadmill, make onJy. Do not use this treadmill in any corn-

sure that the storage latch is fully closed, mercial, rentaJ, or institutional setting.

WARNING: Beforebeginningthisorany0xerc eeprogram,consultyourphysician.

This is especially important for persons over the age of 35 or persons with pre-existing health prob-

lems. Read aH instructions before using. Sears assumes no responsibility for personal injury or

property damage sustained by or through the use of this product.

SAVE THESE iNSTRUCTiONS

The decaJs shown have been placed on your treadmill, if a decaJ is missing, or if it is not Jegible, please

call toll-free 1=806-69g-3756 to order a free replacement decal Apply the decaJ in the tocation shown.

Note: The decals are not shown at actual size.

BEFORE YOU BFGmN

Thank you for selecting the WESLO _ CADENCE 78S

treadmill, The CADENCE 78S treadmill combines

advanced technology with innovative design to let you

enjoy an excellent form of cardiovascular exercise in

the convenience and privacy of your home, And when

you're not exercising, the unique CADENCE 78S

treadmill can be folded up, requiring less than half the

floor space of other treadmills,

For your benefit, read this manuaJ carefully before

using the treadmill, if you have questions after read-

ing this manual, call 1-800-4-MY-HOME _ (1-800-469-

4663),To help us assist you, please note the product

model number and serial number before calling, The

model number of the treadmill is 831,295021, The ser-

ial number can be found on a decal attached to the

treadmill (see the front cover of this manual for the

location),

Before reading further, please review the drawing

below and familiarize yourself with the labeled parts,

Walking Belt

Foot Rails

BACK

Rear Roller

Adjustment Bolts

Console

Handrail --

Storage Latch

Upright

Incline Leg

Water Bottle Holder

(Bottle not included)

Key/Clip

FRONT

Circuit Breaker

Power Cord

RIGHT SIDE

Assembly requires two persons. Set the treadmHUin a cleared area and remove aHpacking materiaUs, Do not

dispose of the packing materiaUsuntil assembUy is compUeted,

Note: The underside of the treadmill walking belt is coated with high-performance lubricant, During shipping, a

small amount of lubricant may be transferred to the top of the walking belt or the shipping carton, This is a nor-

mal condition and does not affect treadmill pedormance, if there is lubricant on top of the walking belt, simply

wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner,

Assembly requires the included allen wrenches _ and your own phillips screwdriver

wire cutters ___._4o_, and needtenose pliers

To identify small parts, use the PART IDENTIFICATION CHART attached in the center of this manual

Note: if a part is not in the parts bag, first check to see if it has been prs-assembUsd, If a part is missing,

call toll-free 1-888-899-3758.

1, Make sure that the power cord is unpJugged.

With the help of a second person, carefully raise the

Uprights (88) until the treadmill is in the position shown,

Cut the tie (not shown) off the right Upright (38),

insert one of the Extension Legs (15) into the treadmill

as shown, Make sure that the Base Pad (33) is on the

indicated side, Note: it may be helpful to tip the Uprights

(38) in the direction shown by the arrow as you insert

the Extension Leg,

Attach the Extension Leg (15) with an Extension Leg

Screw (14), Make sure to push on the head of the

Extension Leg Screw while tightening it.

Attach the other Extension Leg (15) in the same way,

3,fftherearepUastictiesinthebracketsontheHandrails

(4),removetheplasticties,HoUdoneoftheHandrails

neartherightUpright(38)asshown,[nserttheWire

Harness(53)upthroughthebracketontheHandrailand

outoftheroundhoUeinthesideoftheHandrail,ffneces-

sary,useneedUenoseplierstopulltheWireHarnessout

ofthehoUe,Becarefu[notto damagetheWire

Harness.

[nsertthebracketsontheHandrails(4)intotheupper

endsoftheUprights(38),

Fingertightenfour1"BoUts(16)withHandrailWashers

(40)intotheUprights(38)andtheHandrails(4),

4\ \Connectors

\ 53

Bracket

4, Set the ConsoUe Base (87) on the Handrails (4), Thread

four 3/4" Screws (5) into the Handrails and the ConsoUe

Base, After you have started aHfour Screws, tighten the

Screws until they are snug; do not overtighten the

Screws. Note: It may be helpful to press down on the

top of the Console Base above the Handrails as you

tighten the Screws,

See step 3. Firmly tighten, but do not overtighten,

the four 1" Bolts (16).

hsert the Wire Harness (53) through the two indicated

plastic ties on the Console Base (87) and up through the

hole in the Console Base.

5. Hold the Console (11) near the Console Base (87).

Touch the right Handrait (4) to discharge any static.

Next, insert the Wire Harness (53) through the plastic fie

labeled C in the drawing at the right,

Locate the two connectors on the Wire Harness (53),

Plug the wider connector into the connector labeled A in

the drawing at the right (see drawing 5b), The connec-

tors should slide together easily and snap into

place, If they do not, turn the connector on the Wire

Harness and try again, Insert the other connector

through the plastic tie labeled D; plug the connector into

the connector labeled B (see drawing 5c), IF THE CON-

NECTORS ARE NOT INSERTED PROPERLY, THE

CONSOLE MAY BE DAMAGED WHEN THE POWER

IS TURNED ON.

See drawing 5a, Pull any slack in the Wire Harness (53)

through the two ties, Make sure that the end of the Wire

Harness indicated by the arrow is routed as shown,

Securely tighten the plastic ties around the Wire

Harness (53). Cut off the end of each plastic tie,

T[es

5 11

Set the Console (11) in the Console Base (87), Make sure

that no wires are pinched, insert as much of the Wire

Harness (53) as possible down into the hole in the right

Handrail (4), Securely tighten the plastic tie nearest to

the right Handrail. Puil any excess Wire Harness

between the plastic ties tight and tighten the other plastic

tie, Cut off the ends of the plastic ties, Cover the Wire

Harness with the Wire Cover (10), and route the Wire

Harness out of the hole in the side of the Wire Cover,

Attach the Wire Cover to the back of the Console Base

with two 3/4" Screws (5), Do not overtighten the Screws.

Make sure that no wires are pinched before you

attach the Console (!!) to the Console Base (87).

Tighten five 3/4" Screws (5) into the Console Base and

the Console in the locations shown, Note: No 3/4"

Screw goes into the hole indicated by the arrow. Do

not overtighten the Screws.

Attach the Storage Latch (66) to the left Upright (38)

with two 3/4" Screws (5),

Ties

No 11

87 Screw

8, Make sure that aH parts used in assembly are properly tightened before you use the treadmill Keep

the included allen wrench in a secure place. The allen wrench is used to adjust the wa[Mng belt (see page

13), To protect the floor or carpet, place a mat under the treadmilL

OPERATION AND ADJUSTMENT

THE PRE-LUBRmCATED WALKmNG BELT

Your treadmHUfeatures a waUkingbeUtcoated with high°

performance Uubrbant, IMPORTANT: Never apply siF

icone spray or other substances to the walking

belt or the walking platform. Such substances will

deteriorate the walking belt and cause excessive

wear.

HOW TO PLUG IN THE POWER CORD

DANG ER: Improperconnection

of the equipment_grounding conductor can

result in an increased risk of electric shock.

Check with a qualified electrician or service-

man if you are in doubt as to whether the

product is properly grounded. Do not modify

the plug provided with the product--if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician,

Your treadmill, like any other type of sophisticated

electronic equipment, can be seriously damaged by

sudden voltage changes in your home's power,

Voltage surges, spikes, and noise intederence can

result from weather conditions or from other appli-

ances being turned on or off, To decrease the pos-

sibility of your treadmill being damaged, aJways

use a surge suppressor with your treadmill (see

drawing 1 at the right}. To purchase a surge sup-

pressor, see your Jocal Sears store or call !-800-

368-7278 and order part number 148148, or see

your tocal electronics store.

Use onJy a singJe-ouflet surge suppressor that is

UL 1449 tisted as a transient voJtage surge sup-

pressor (TVSS). The surge suppressor must have

a UL suppressed voJtage rating of 400 voJts or tess

and a minimum surge dissipation of 450 jouJes.

The surge suppressor must be electrically rated

for 120 voffs AC and 15 amps. There must be a

monitoring Jight on the surge suppressor to indi-

cate whether it is functioning properly. Failure to

use a property functioning surge suppressor could

resuff in damage to the control system of the

treadmill. If the contro! system is damaged, the

waJking beJt may change speed, accelerate or stop

unexpectedly, which may result in a fall and seri-

ous injury.

This product must be grounded, if it should mal-

function or break down, grounding provides a path of

least resistance for electric current to reduce the risk

of electric shock, This product is equipped with a cord

having an equipment-grounding conductor and a

grounding plug. Plug the power cord into a surge

suppressor, and plug the surge suppressor into an

appropriate outlet that is properly installed and

grounded in accordance with aH JocaJ codes and

ordinances. Important: The treadmill is not com-

patible with GFCl-equipped outlets.

This product is for use on a nominal 120-volt circuit,

and has a grounding plug that looks like the plug illus-

trated in drawing 1 below, A temporary adapter that

looks like the adapter illustrated in drawing 2 may be

used to connect the surge suppressor to a 2-pole

receptacle as shown in drawing 2 if a properly

grounded outlet is not available,

IGrounded Outlet Box

_--.. I -- Surge Suppressor

"_ Grounding Pin

Grounding Pin

_rounded Outlet G g Hug

2_rounded Outlet Box

Adapter Surge Suppressor

The temporary adapter should be used only until a

properly grounded outlet (drawing 1) can be installed

by a qualified electrician,

The green-colored rigid ear, lug, or the like extending

from the adapter must be connected to a permanent

ground such as a properly grounded outlet box cover,

Whenever the adapter is used it must be held in place

by a metal screw, Some 2-pole receptacJe outlet

box covers are not grounded. Contact a qualified

electrician to determine if the outlet box cover is

grounded before using an adapter.

DmAGRAM OF THE CONSOLE

TRAINING ZONES

20 125 145 165

30 120 138 155

40 115 130 145

50 110 125 140

60 105 118 130

70 95 110 125

80 90 103 115

> _ _ >

_ ?< O

Displays

EJq,,s s.soj

TIME DISTANCE CALORIES SPEED

POWER INCliNE DIGITAL SPEED

V V

Incline ControU Speed Control

Note: if there is a thin sheet of

plastic on the console, remove it.

WARNING:

To r_duce risk al sedoas

r,iu f y, s_and on faai rails

before s_ar_ing treadmill

cad al/d understand the

user's ,r,ar,ual, all ms_ruc-

otis, a_d he wanli,_gs

beFo euse

Keep children away

CAUTION: Betoreoperat ogthe

console, read the following precautions.

oDo not stand on the walking belt when turn-

ing on the power.

oAJwaye wear the clip (see the drawing at the

right) whib operating the treadmill

- Adjust the speed in small increments to

avoid sudden jumps in speed.

o To reduce the possibility of electric shock,

keep the console dry. Avoid spiJJing liquids

on the console and place onJy a sealed

water bottJe in the water bottle hoJder.

STEP-BY-STEP CONSOLE OPERATION

Before operating the console, make sure that the

power cord is properly plugged in (see page 8).

Next, locate the circuit break-

er near the power cord. Make

sure that the circuit breaker is

in the reset position. Reset

Stand on the foot rails of

the treadmill. Find the

clip attached to the key,

and slide the clip onto

the waistband of your

clothes.

Clip

Next, insert the key fully into the console. After a

moment, the displays wiii light. Test the cJip by care-

fuJty taking a few steps backward untJJ the key is

pulled from the consoJe. If the key is not pulled

from the consoJe, adjust the position of the cJip.

Follow the steps below to operate the console.

Insert the key futty into the consote.

A few seconds after the key is inserted, the dis-

plays will light.

Press the Speed/_ button to start the waJking

belt.

A moment after the button is pressed, the walking

belt will begin to move, Hold the handrails and

begin walking,

As you exercise, change the speed of the walking

beR as desired by pressing the Speed buttons.

Each time a button is pressed, the speed setting

wifl change by 0.1 mph; if a button is held down,

the speed setting wifl change in increments of 0.5

mph. Note: The console can display speed and

distance in either miles or kiJometers (see

CALORIES/SPEED DISPLAY at the right}. For

simpJicity, all instructions in this section refer

to mites.

To stop the walking belt, press the Stop button.

The Time/Dbtance display wifl begin to flash.

Note: During the first few minutes that the treadmifl

is used, inspect the alignment of the walking belt,

and align it if necessary (see page 13).

Change the incline of the treadmill as desired.

To change the incline of the treadmill, press either

of the Incline buttons until the desired incline level

is reached.

Fottow your progress with the displays.

Time/Distance

dispJay--This display

shows the elapsed time

and the distance that you

have walked or run. The

display will change from

one number to the other

Mode indicator

TiME DISTANCE

every few seconds, as shown by the mode indica-

tors. When the Stop button is pressed, the display

will flash.

Calories/Speed

display--This display

shows the approximate

number of calories you

have burned and the

speed of the walking

belt. The display wiil change from one number to

the other every few seconds, as shown by the

mode indicators.

Note: The console can

display speed and dis-

tance in either miles or

kilometers. To change

the unit of measurement,

hold down the Stop but-

CALORIES SPEED

ton, insert the key into the console, and continue to

hold the Stop button for a moment. An "E" for

English miles or an "M" for metric kilometers will

appear in the Calories/Speed display. Press the

Speed iE button to change the unit of measure-

ment. When the desired unit of measurement is

selected, remove the key and then reinsert it.

To reset the displays, press the Stop button,

remove the key, and then reinsert the key.

When you are finished exercising, remove the

key.

Step onto the foot rails, press the Stop button, and

remove the key from the console. Keep the key in a

secure place.

Dieses Handbuch passt für folgende Modelle

Andere Weslo Tretmühle Handbücher

Weslo

Weslo Cadence 10.0s Bedienungsanleitung

Weslo

Weslo Cadence 60 Se Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 1050 Bedienungs- und Wartungshandbuch

Weslo

Weslo Cadence 5.2 W/elec Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 915 Bedienungsanleitung

Weslo

Weslo Cadence S5 Treadmill Kurzanleitung

Weslo

Weslo Cadence 715 Treadmill Bedienungsanleitung

Weslo

Weslo WCTL39102 Bedienungsanleitung

Weslo

Weslo WCTL41590 Bedienungsanleitung

Weslo

Weslo Cadence 16.0 Cwl Treadmill Systemhandbuch

Weslo

Weslo Cadence Ls10 Bedienungsanleitung

Weslo

Weslo 10pi Bedienungsanleitung

Weslo

Weslo Cadence 150 Treadmill Bedienungs- und Wartungshandbuch

Weslo

Weslo cadence 820 WETL91000 Bedienungsanleitung

Weslo

Weslo Cadence G 7.0 WLTL39810.0 Bedienungsanleitung

Weslo

Weslo Cadence 50 Ls Benutzerhandbuch

Weslo

Weslo WLTL29606.1 Bedienungsanleitung

Weslo

Weslo CADENCE 880 Bedienungsanleitung

Weslo

Weslo Cadence 10.0i Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 85 Kurzanleitung

Weslo

Weslo WLTL26080 Bedienungsanleitung

Weslo

Weslo Pro Crosswalk 7.8 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 300 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 450v Treadmill Systemhandbuch

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung