Weslo WLTL25320 Bedienungsanleitung

Model No. WLTL25320

Serial No.

Write the serial number in the

space above for future reference.

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. Save this manual

for future reference.

USER'S MANUAL

Serial

Number

Decal

Visit our website at

www.weslo.com

new products, prizes,

fitness tips, and much more!

QUESTIONS?

If you have questions, or if there

are missing parts, we will guar-

antee complete satisfaction

through direct assistance from

our factory.

TO AVOID DELAYS, PLEASE

CALL DIRECT TO OUR TOLL-

FREE CUSTOMER HOT LINE.

The trained technicians on our

Customer Hot Line will provide

immediate assistance, free of

charge to you.

CUSTOMER HOT LINE:

1-800-999-3756

Mon.–Fri., 6 a.m.–6 p.m. MST

TABLE OF CONTENTS

IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10

MAINTENANCE AND TROUBLE-SHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

ORDERING REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Back Cover

LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover

Note: A PART IDENTIFICATION CHART, an EXPLODED DRAWING, and a PART LIST are attached in the

center of this manual.

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately

informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least eight feet of clearance behind it and two

feet on each side. Do not place the treadmill

on any surface that blocks air openings. To

protect the floor or carpet from damage,

place a mat under the treadmill.

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a

garage or covered patio, or near water.

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being

administered.

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should not be used by persons

weighing more than 250 pounds.

8. Never allow more than one person on the

treadmill at a time.

9. Wear appropriate exercise clothing when

using the treadmill. Do not wear loose cloth-

ing that could become caught in the tread-

mill. Athletic support clothes are recommend-

ed for both men and women. Always wear

athletic shoes. Never use the treadmill with

bare feet, wearing only stockings, or in san-

dals.

10. When connecting the power cord (see page 8),

plug the power cord into a surge suppressor

(not included) and plug the surge suppressor

into a grounded circuit capable of carrying 15

or more amps. No other appliance should be

on the same circuit. Do not use an extension

cord.

11. Use only a single-outlet surge suppressor that

meets all of the specifications described on

page 8. To purchase a surge suppressor, see

your local WESLO dealer or call 1-800-806-

3651 and order part number 146148.

12. Failure to use a properly functioning surge

suppressor could result in damage to the con-

trol system of the treadmill. If the control sys-

tem is damaged, the walking belt may change

speed or stop unexpectedly, which may result

in a fall and serious injury.

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if

the power cord or plug is damaged, or if the

treadmill is not working properly. (See page 4

if the treadmill is not working properly.)

15. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the

handrails while using the treadmill.

WARNING:To reduce the risk of burns, fire, electric shock, or injury to persons, read

the following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

16. The treadmill is capable of high speeds.

Adjust the speed in small increments to

avoid sudden jumps in speed.

17. Never leave the treadmill unattended while it is

running. Always remove the key and unplug

the power cord when the treadmill is not in

use.

18. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See

ASSEMBLY on page 5, and HOW TO MOVE

THE TREADMILL on page 11.) You must be

able to safely lift 45 pounds (20 kg) in order

to raise, lower, or move the treadmill.

19. Do not change the incline of the treadmill by

placing objects under the treadmill.

20. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

21. Inspect and properly tighten all parts of the

treadmill regularly.

22. Never drop or insert any object into any

opening.

23. DANGER:Always unplug the power

cord immediately after use, before cleaning

the treadmill, and before performing the

maintenance and adjustment procedures

described in this manual. Never remove the

motor hood unless instructed to do so by an

authorized service representative. Servicing

other than the procedures in this manual

should be performed by an authorized ser-

vice representative only.

24. This treadmill is intended for in-home use

only. Do not use this treadmill in any com-

mercial, rental, or institutional setting.

WARNING:Before beginning this or any exercise program, consult your physician.

This is especially important for persons over the age of 35 or persons with pre-existing health prob-

lems. Read all instructions before using. ICON assumes no responsibility for personal injury or prop-

erty damage sustained by or through the use of this product.

SAVE THESE INSTRUCTIONS

The decals shown have been placed on

your treadmill. If a decal is missing, or if it

is not legible, please call our Customer

Service Department, toll-free, to order a

free replacement decal (see ORDERING

REPLACEMENT PARTS on the back cover

of this manual). Apply the decal in the

location shown. Note: The decals are not

shown at actual size.

¥Hazardous Voltage

¥Risk of Electric Shock

¥Unplug Treadmill before Assemb

/Disassembly.

BEFORE YOU BEGIN

Handrails

Console

Storage Latch

Key/Clip

Circuit Breaker

Walking Belt

Foot Rails

Incline Leg

Incline Pin

Power Cord

FRONT

BACK

RIGHT SIDE

Rear Roller

Adjustment Bolts

Water Bottle Holder

(Bottle not included)

Accessory Tray

Uprights

Thank you for selecting the WESLO®CADENCE C32

treadmill. The CADENCE C32 treadmill combines

advanced technology with innovative design to let you

enjoy an excellent form of cardiovascular exercise in

the convenience and privacy of your home. And when

you’re not exercising, the unique CADENCE C32 can

be folded up, requiring less than half the floor space of

other treadmills.

For your benefit, read this manual carefully before

using the treadmill. If you have additional questions,

please call our Customer Service Department toll-free

at 1-800-999-3756, Monday through Friday, 6 a.m.

until 6 p.m. Mountain Time (excluding holidays). To

help us assist you, please note the product model

number and serial number before calling. The model

number of the treadmill is WLTL25320. The serial num-

ber can be found on a decal attached to the treadmill

(see the front cover of this manual for the location).

Before reading further, please review the drawing

below and familiarize yourself with the labeled parts.

ASSEMBLY

Assembly requires two persons. Set the treadmill in a cleared area and remove all packing materials; do not

dispose of the packing materials until assembly is completed. Note: The underside of the treadmill walking

belt is coated with high-performance lubricant. During shipping, a small amount of lubricant may be transferred

to the top of the walking belt or the shipping carton. This does not affect treadmill performance. If there is lubri-

cant on top of the walking belt, simply wipe off the lubricant with a soft cloth and a mild, non-abrasive cleaner.

Assembly requires a phillips screwdriver , two adjustable wrenches , and

needlenose pliers .

Attach four Base Pads (63) to the bottom of the Base

(46) with four 3/4” Tek Screws (3). Attach the Wheels

(68) to the outside of the Base with two Wheel Bolts (67),

3/8” Washers (66), and 3/8” Nuts (61) as shown. Do not

overtighten the Wheel Bolts.

68 67

66 63

2. With the help of a second person, carefully tip the tread-

mill onto its right side as shown.

Attach a Frame Spacer (27) to the Frame (79) with a

Spacer Screw (89) as shown.

Identify the Left Upright (53), which does not have a large

round hole near the lower end. Hold the Left Upright so

the indicated small hole is in the position shown. Loosely

thread a Frame Bolt (70) with a Washer (66) and a Star

Washer (29) through the Left Upright and the Frame

Spacer (27) into the Frame (79) as shown. Do not tight-

en the bolts used in steps 2 through 5 until step 5 is

completed.

Refer to drawing 2b. With the help of a second person, tip

the treadmill onto its left side.

Attach a Frame Spacer (27) to the Frame (79) with a

Spacer Screw (89).

Hold the Right Upright (62) so the indicated large hole is

in the position shown. Insert the Wire Harness (60) into

the large hole and out of the top of the Right Upright.

Loosely thread a Frame Bolt (70) with a Washer (66) and

a Star Washer (2) through the Right Upright (62) and the

Frame Spacer (27) into the Frame (79).

Large

Hole

Small

Hole

29 62

1. Note: To identify small parts used during assembly,

refer to the PART IDENTIFICATION CHART in the

center of this manual.

¥Hazardous Voltage

¥Risk of Electric Shock

¥Unplug Treadmill before Assembly

/Disassembly.

3. With the help of a second person, attach the Base (46)

to the Right Upright (62) with two Upright Bolts (65), two

3/8” Washers (66), and two 3/8” Nuts (61) as shown.

Attach the Base (46) to the Left Upright (not shown) in

the same way.

365 66

62 46

4. Raise the treadmill to the upright position.

If there are plastic ties in the brackets on the Left and

Right Handrails (45, 59), remove them. Hold the Right

Handrail near the Right Upright (62). Insert the Wire

Harness (60) up through the bracket on the Right

Handrail and out of the round hole in the center of the

Handrail. If necessary, use needlenose pliers to pull the

Wire Harness out of the hole. Be careful not to damage

the Wire Harness. Insert the brackets into the tops of

the Left and Right Uprights (53, 62).

Hand tighten four Handrail Bolts (42) with 1/4” Washers

(38) into the Uprights (53, 62) and the Handrails (45, 59).

Remove the tape from the connectors at the end of the

Wire Harness (60).

Connectors

Bracket

59 45

5. Set the Console Base (52) on the Handrails (45, 59).

Thread four 3/4” Screws (2) into the Handrails and the

Console Base. After you have started all four Screws,

tighten the Screws until they are snug; do not over-

tighten the Screws.

Firmly tighten but do not overtighten the bolts used

in steps 2 through 4.

Hinges

6. Insert the Battery Cover (54) up through the bottom of

the Console Base (52), with the hinges in the position

shown. The Cover should pivot down, away from the

Console Base.

10.Make sure that all parts used in assembly are properly tightened before you use the treadmill. Keep

the included allen wrench in a secure place. The allen wrench is used to adjust the walking belt (see page

13). To protect the floor or carpet, place a mat under the treadmill.

48 2

9. Attach the Storage Latch (48) to the Left Upright (53)

with two 3/4” Screws (2).

222

8. Set the Console (57) in the Console Base (52). Cover

the Wire Harness (60) with the Wire Cover (11), and

route the Wire Harness out of the hole in the side of the

Wire Cover. Attach the Wire Cover to the back of the

Console Base with two 3/4” Screws (2). Make sure that

no wires are pinched before you attach the Console

to the Console Base.

Tighten four 3/4” Screws (2) into the Console Base (52)

and the Console (57). Do not over tighten the Frame

Bolts (70).

7. Hold the Console (57) near the Console Base (52).

Touch the Right Handrail (59) to discharge any static.

Insert the Wire Harness (60) through the hole in the bot-

tom of the Console Base (52). Locate the two wires in

the Wire Harness (60) that have L-shaped connectors

on the ends. Press the connectors onto the two tabs on

the switch shown in inset drawing 7a. Connect the other

two wires in the Wire Harness to the back of the

Console (57) in the locations shown by the arrows in

drawing 7. If the connectors do not fit together

easily, rotate them and then connect them.

Make a loop with each of the indicated plastic ties around

the Wire Harness (60). Securely tighten each plastic

tie to prevent the Wire Harness from slipping. Cut off

the ends of the plastic ties.

7a Tabs

Ties

59 45

OPERATION AND ADJUSTMENT

THE PERFORMANT LUBETM WALKING BELT

Your treadmill features a walking belt coated with

PERFORMANT LUBETM, a high-performance lubricant.

IMPORTANT: Never apply silicone spray or other

substances to the walking belt or the walking plat-

form. Such substances will deteriorate the walking

belt and cause excessive wear.

HOW TO PLUG IN THE POWER CORD

Your treadmill, like any other type of sophisticated

electronic equipment, can be seriously damaged by

sudden voltage changes in your home’s power.

Voltage surges, spikes, and noise interference can

result from weather conditions or from other appli-

ances being turned on or off. To decrease the pos-

sibility of your treadmill being damaged, always

use a surge suppressor with your treadmill (see

drawing 1 at the right). To purchase a surge sup-

pressor, see your local WESLO dealer or call

1-800-806-3651 and order part number 146148.

Use only a single-outlet surge suppressor that is

UL 1449 listed as a transient voltage surge sup-

pressor (TVSS). The surge suppressor must have

a UL suppressed voltage rating of 400 volts or

less and a minimum surge dissipation of 450

joules. The surge suppressor must be electrically

rated for 120 volts AC and 15 amps. There must be

a monitoring light on the surge suppressor to indi-

cate whether it is functioning properly. Failure to

use a properly functioning surge suppressor

could result in damage to the control system of

the treadmill. If the control system is damaged, the

walking belt may change speed or stop unexpect-

edly, which may result in a fall and serious injury.

This product must be grounded. If it should mal-

function or break down, grounding provides a path of

least resistance for electric current to reduce the risk

of electric shock. This product is equipped with a cord

having an equipment-grounding conductor and a

grounding plug. Plug the power cord into a surge

suppressor, and plug the surge suppressor into an

appropriate outlet that is properly installed and

grounded in accordance with all local codes and

ordinances. Important: The treadmill is not com-

patible with GFCI-equipped outlets.

This product is for use on a nominal 120-volt circuit,

and has a grounding plug that looks like the plug illus-

trated in drawing 1 below. A temporary adapter that

looks like the adapter illustrated in drawing 2 may be

used to connect the surge suppressor to a 2-pole

receptacle as shown in drawing 2 if a properly

grounded outlet is not available.

The temporary adapter should be used only until a

properly grounded outlet (drawing 1) can be installed

by a qualified electrician.

The green-colored rigid ear, lug, or the like extending

from the adapter must be connected to a permanent

ground such as a properly grounded outlet box cover.

Whenever the adapter is used it must be held in place

by a metal screw. Some 2-pole receptacle outlet

box covers are not grounded. Contact a qualified

electrician to determine if the outlet box cover is

grounded before using an adapter.

DANGER:Improper connection

of the equipment-grounding conductor can

result in an increased risk of electric shock.

Check with a qualified electrician or service-

man if you are in doubt as to whether the

product is properly grounded. Do not modify

the plug provided with the product—if it will

not fit the outlet, have a proper outlet

installed by a qualified electrician.

Grounded Outlet Box

Grounding Plug

Surge Suppressor

Grounding Pin

Adapter

Lug

Metal Screw

Grounded Outlet

Grounding Pin

CAUTION:Before operating the

console, read the following precautions.

• Do not stand on the walking belt when turning

on the power.

• Always wear the clip (see the drawing below)

while using the treadmill. When the key is

removed from the console, the walking belt

will stop.

• Adjust the speed in small increments.

• To reduce the possibility of electric shock,

keep the console dry. Avoid spilling liquids on

the console. Put only sealable water bottles in

the water bottle holders.

BATTERY INSTALLATION

The console

requires two

"AA" batteries

(not included).

Alkaline batter-

ies are recom-

mended.

To install bat-

teries, open

the battery

cover beneath

the console as

shown. Press

two batteries

into the console. Make sure that the negative (–)

ends of the batteries are touching the springs.

Close the battery cover, push up on the tab, and then

push the tab forward as shown in the inset drawing.

Make sure that the tab locks into place.

STEP-BY-STEP CONSOLE OPERATION

Before operating the console, make sure that the

power cord is properly plugged in (see page 8).

Step onto the

foot rails of the

treadmill. Find

the clip attached

to the key, and

slide the clip

onto the waist-

band of your

clothes. Next,

insert the key

fully into the con-

sole. Test the clip by carefully taking a few steps

backward until the key is pulled from the console.

If the key is not pulled from the console, adjust

the position of the clip as needed.

DIAGRAM OF THE CONSOLE

Speed Control

Displays

Batteries

Note: If there is a thin sheet of clear plastic

on the face of the console, remove it before

operating the console.

Clip

Key

Tab

Follow the steps below to operate the console.

Insert the key fully into the console.

Inserting the key will not turn on the displays. The

displays will turn on when the ON/RESET button is

pressed or when the walking belt is started. Note:

If you just installed batteries, the displays will

already be on.

Reset the speed control and start the walking

belt.

Slide the speed control

down to the RESET

position. Note: Each

time the walking belt

is stopped, the speed

control must be

moved to the RESET

position before the

walking belt can be

restarted.

Next, slowly slide the speed control up until the

walking belt begins to move at slow speed.

Carefully step onto the walking belt and begin

walking. Change the speed of the walking belt as

desired by sliding the speed control.

To stop the walking belt, step onto the foot rails

and slide the speed control to the RESET position.

Note: During the first few minutes that the treadmill

is used, inspect the alignment of the walking belt

and align it if necessary (see page 13).

Monitor your progress with the displays.

TIME/DISTANCE dis-

play—This display

shows the elapsed time

and distance that you

have walked or run, in

miles. Every few sec-

onds, the display will

change from one number to the other, as shown

by the arrows in the display.

CALS/FAT CALS/

SPEED display—This

display shows the

approximate numbers

of calories and fat calo-

ries you have burned.

(See FAT BURNING on

page 14.) In addition, the display shows the speed

of the walking belt, in miles per hour. Every few

seconds, the display will change from one number

to the next, as shown the the arrows in the display.

To reset the displays at any time, press the

ON/RESET button.

When you are finished exercising, stop the

walking belt and remove the key.

Step onto the foot rails, slide the speed control to

the RESET position, and remove the key from the

console. The displays will turn off a few minutes

after the key is removed. Note: Any time that the

walking belt is stopped and the ON/RESET but-

ton is not pressed for a few minutes, the dis-

plays will automatically turn off.

HOW TO CHANGE THE INCLINE OF THE TREADMILL

To vary the intensity of your exercise, the incline of the

treadmill can be changed. There are four incline levels.

Before changing the incline, remove the key and

unplug the power cord. Next, fold the treadmill to the

storage position (see HOW TO FOLD THE TREAD-

MILL FOR STORAGE on page 10).

To change the incline, first remove the incline pin from

one of the incline legs as shown below. Adjust the

incline leg to the desired height and fully reinsert the

incline pin. Make sure that the incline pin is in the

“locked” position shown in the inset drawing. Adjust the

other incline leg in the same way. Make sure that

both incline pins are inserted from the direction

shown.

CAUTION: Before using the treadmill, make sure

that both incline legs are at the same height. Do

not use the treadmill with the incline pins removed.

After you have adjusted the incline legs, lower the

treadmill (see HOW TO LOWER THE TREADMILL

FOR USE on page 11).

Incline

Arrow

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Weslo Tretmühle Handbücher

Weslo

Weslo Cadence S5 Treadmill Benutzerhandbuch

Weslo

Weslo Cadence 200 Bedienungsanleitung

Weslo

Weslo Cadence 55 Treadmill Benutzerhandbuch

Weslo

Weslo Cadence A60 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence S 8 Bedienungsanleitung

Weslo

Weslo WLTL33090 Bedienungsanleitung

Weslo

Weslo Cadence 200 Treadmill Benutzerhandbuch

Weslo

Weslo CADENCE 1020 WETL28090 Bedienungsanleitung

Weslo

Weslo Cadence 6.9 Ery Treadmill Benutzerhandbuch

Weslo

Weslo Cadence 5.0 Treadmill Bedienungsanleitung

Weslo

Weslo Easy compact 2 treadmill Handbuch

Weslo

Weslo CADENCE LX25 Bedienungsanleitung

Weslo

Weslo Cadence 840 Bedienungsanleitung

Weslo

Weslo Lyne 3500 Treadmill Bedienungsanleitung

Weslo

Weslo Cardiostride 3.0 Treadmill Bedienungsanleitung

Weslo

Weslo Cadence 200cs Bedienungsanleitung

Weslo

Weslo Aerobicstride 2.0 Treadmill Bedienungsanleitung

Weslo

Weslo Easy compact 2 treadmill Technisches Datenblatt

Weslo

Weslo WLTL27081 Bedienungsanleitung

Weslo

Weslo Cadence 255 Dr Treadmill Bedienungsanleitung

Weslo

Weslo EPIC ESP Fitness Bedienungsanleitung

Weslo

Weslo Cadence 1000 Fm Bedienungsanleitung

Weslo

Weslo Relay 440 Bedienungsanleitung

Weslo

Weslo Lyne 3500 Treadmill Kurzanleitung

Beliebte Tretmühle Handbücher anderer Marken

Treadly

Treadly TREADLY 2 Bedienungsanleitung

HEALTH ONE

HEALTH ONE Walk Ro Bedienungsanleitung

NordicTrack

NordicTrack T7.5 S Bedienungsanleitung

Gold's Gym

Gold's Gym ADVANTAGE GGTL12920 Bedienungsanleitung

Merax

Merax MS282992 Bedienungsanleitung

FYTTER

FYTTER RU-2SX Bedienungsanleitung

Precor

Precor 903 Bedienungsanleitung

FitLogic

FitLogic freewill d225 Bedienungsanleitung

HOP-SPORT

HOP-SPORT ESTIMA HS-3200LB Bedienungsanleitung

Horizon Fitness

Horizon Fitness Adventure 5 Plus Bedienungsanleitung

Stamia

Stamia InMotion II Bedienungsanleitung

Smooth Fitness

Smooth Fitness EVO 3i Bedienungsanleitung

NordicTrack

NordicTrack NETL81810.0 Bedienungsanleitung

Schwinn

Schwinn 830/Journey 8.0 Bedienungsanleitung

Keys Fitness

Keys Fitness HealthTrainer HT-740T Bedienungsanleitung

Spirit

Spirit XT8 Bedienungsanleitung

NordicTrack

NordicTrack T 14.0 Treadmill Bedienungsanleitung

Master

Master F22 Bedienungsanleitung