Zeiss Axiocam 105 color Bedienungsanleitung

Instruction Manual

ZEISS Axiocam 105 color

Version R2

ZEISS Axiocam 105 color

Original Manual

Carl Zeiss Microscopy GmbH

Carl-Zeiss-Promenade 10

07745 Jena

Germany

[email protected]

www.zeiss.com/microscopy

Carl Zeiss Microscopy GmbH

Carl-Zeiss-Promenade 10

07745 Jena

Germany

Document Name: Instruction Manual ZEISS Axiocam 105 color

Order Number: 426555-7010-001

Revision: 2

Language: en-US

Effective from: 09/2022

reproduced or transmitted in any form or by any means - including electronic or mechanic methods, by photocopy-

ing, recording or by any information or filing system. The right to make backup-copies for archiving purposes shall

remain unaffected thereby. Any violations may be prosecuted as copyright infringements.

The use of general descriptive names, registered names, trademarks, etc. in this document does not imply that

such names are exempt from the relevant intellectual property laws and regulations and therefore free for general

use. This shall also apply if this is not specifically referred to. Software programs shall entirely remain the property

of ZEISS. No program or subsequent upgrade thereof may be disclosed to any third party, copied or reproduced in

any other form without the prior written consent of ZEISS, even if these copies or reproductions are destined for

internal use at the customer's only, the only exception being one single back-up copy for archiving purposes.

Content ZEISS

Content

1 About this Instruction Manual....................................................... 5

1.1 Introduction ............................................................................................... 5

1.2 Text Conventions and Link Types................................................................ 5

1.3 Explanation of Warning Messages and Additional Information ................... 6

2 Safety ............................................................................................ 8

2.1 Intended Purpose ....................................................................................... 8

2.2 General Safety Information......................................................................... 8

2.2.1 Requirements for Operators........................................................ 8

2.2.2 Safe Operating Condition ........................................................... 8

2.3 Prevention of Hazards ................................................................................ 9

3 Technical Data and Conformity ..................................................... 10

3.1 Axiocam 105 color R2 ................................................................................ 10

3.1.1 Spectral Sensitivity...................................................................... 11

3.2 Applicable Standards and Regulations ........................................................ 11

4 Shipment ....................................................................................... 12

5 Connecting the Camera ................................................................. 13

5.1 Installing the interface card ........................................................................ 13

5.2 Mounting the camera on the microsope..................................................... 13

5.3 Connecting the camera with PC ................................................................. 13

5.4 Function indicator ...................................................................................... 14

6 Installing Software and Drivers ..................................................... 15

7 Care and Maintenance................................................................... 16

7.1 Optical System ........................................................................................... 16

7.2 Cleaning the infrared filter or protective glass............................................. 16

8 Troubleshooting ............................................................................ 17

8.1 The camera does not appear in the menu of selectable cameras ................ 17

8.2 You don't see a camera image on your screen ........................................... 17

8.3 The color of my image does not correspond to the impression through the

ocular......................................................................................................... 17

8.4 The performance of the camera is not consistent or is too slow ................. 17

Instruction Manual ZEISS Axiocam 105 color | en-US | Rev.2 | 426555-7010-001 3

Content ZEISS

9 Disposal......................................................................................... 18

Instruction Manual ZEISS Axiocam 105 color | en-US | Rev.2 | 426555-7010-001 4

1 About this Instruction Manual | 1.1 Introduction ZEISS

1 About this Instruction Manual

This Instruction Manual (further called "document") is considered to be part of the microscope

camera, herein after referred to as the "product" or the "camera".

This document contains basic steps and safety information that must be observed during opera-

tion and maintenance. Therefore, the document must be read by the operator prior to commis-

sioning and must always be available at the place of use of the product.

This document is an essential part of the product and, if the product is resold, the document must

remain with the product or be handed over to the new owner.

1.1 Introduction

This camera is a high-resolution digital microscope camera with a color CMOS sensor and USB 3.0

interface for light microscopy applications. To make it easier for you to set up the camera, follow

the instructions in these chapters step by step. In this manual the interface between the camera

and the computer is called USB 3.0.

Content This document contains all the information you need to set up the microscope, start the software,

and perform troubleshooting and maintenance. It contains the following chapters:

Chapter Content

About this Instruction Manual Introduction and overview about this manual.

Safety Important information on safe handling with the camera.

Read this chapter before unpacking the camera and

putting it into operation.

Technical Data and Conformity Here you will find the camera's technical data.

Shipment The contents of delivery and optional attachments will be

described here.

Connecting the Camera In this chapter you will find detailed instructions on con-

necting and using the camera.

Installing Software and Drivers Here you will learn how to install ZEISS software and cam-

era drivers.

Care and Maintenance This chapter describes some measures for the maintenance

and care of your camera. In case of greater damage, always

contact ZEISS support.

Troubleshooting In this chapter we have listed some solutions to various

problems. If you can not solve your problem, contact ZEISS

support.

Disposal Information on the disposal of the product.

1.2 Text Conventions and Link Types

Example Explanation

The names of controls and important infor-

mation are shown in bold letters, for in-

stance:

Instruction Manual ZEISS Axiocam 105 color | en-US | Rev.2 | 426555-7010-001 5

1 About this Instruction Manual | 1.3 Explanation of Warning Messages and Additional Infor-

mation ZEISS

Example Explanation

Click Start. Software controls and GUI elements.

Press the Standby button. Hardware controls and elements.

Press Enter on the keyboard. Key on the keyboard.

Press Ctrl+Alt+Del. Press several keys on the keyboard simultane-

ously.

Select Tools>Goto Control Panel>Air-

lock.

Follow a path in the software.

Enter example.pdf in this field. Text to be entered by the user.

Programming and Macros Anything typed in literally during program-

ming, including, for example, macro codes,

keywords, data types, method names, vari-

ables, class names, and interface names.

Tab.1: Text conventions

Example Explanation

See: Text Conventions and Link Types [

}

5].Link to further information for this topic.

https://www.zeiss.com/corporate/int/

home.html

Link to a website on the internet.

Tab.2: Link types

1.3 Explanation of Warning Messages and Additional Information

CAUTION, and NOTICE are standard signal words used to determine the levels of hazards and

risks of personal injury and property damage. Not only the safety and warning messages in the

Safety chapter are to be considered also all safety and warning messages in other chapters. Fail-

ure to comply with these instructions and warnings can result in both personal injury and property

damage and involve the loss of any claims for damages.

The following warning messages indicating dangerous situations and hazards are used in this doc-

ument.

CAUTION

Type and source of danger

CAUTION indicates a potentially hazardous situation which, if not avoided, may result in minor

or moderate injury.

NOTICE

Type and source of danger

NOTICE indicates a potentially harmful situation which, if not avoided, may result in property

damage. In addition, NOTICE warns of data loss or corrupt data as well.

Instruction Manual ZEISS Axiocam 105 color | en-US | Rev.2 | 426555-7010-001 6

1 About this Instruction Manual | 1.3 Explanation of Warning Messages and Additional Infor-

mation ZEISS

Info

Provides additional information or explanations to help operator better understand the con-

tents of this document.

Instruction Manual ZEISS Axiocam 105 color | en-US | Rev.2 | 426555-7010-001 7

2 Safety | 2.1 Intended Purpose ZEISS

2 Safety

2.1 Intended Purpose

The product is a high definition microscope camera for color imaging. It is suitable for use as an

accessory for educational and routine microscopy in laboratory environments and for use by

trained laboratory personnel. The camera has been designed to be used in the field of light mi-

croscopy for general observation, routine work, and simple applications in which a sufficient

amount of light is available.

The camera should only be used for training and research. The images / videos from this camera

must not be used for the direct generation of diagnostic results.

2.2 General Safety Information

This document must be read before commissioning in order to ensure safe and uninterrupted op-

eration. Pay particular attention to all listed safety notes. Make sure, that

§the operating personnel has read and understood this manual, associated documents, and

particularly all safety regulations and instructions, and applies them.

§the local and national safety and accident prevention regulations must be observed, as well as

the applicable laws and regulations in your country.

§this document is always available at the place of use of the product.

§the product is always in perfect condition.

§the product is secured against access by unauthorized persons.

§maintenance and repair work, retrofitting, removal or replacement of components, as well as

any other intervention in the product not described in this document, may only be carried out

by the manufacturer ZEISS or persons expressly authorized by ZEISS to do so.

2.2.1 Requirements for Operators

The product, components, and accessories may only be operated and maintained by authorized

and trained personnel. The product may only be used in accordance with this document. If the

product is not used as described, the safety of the user may be impaired and/or the product may

be damaged.

Any unauthorized intervention or use other than within the scope of the intended use shall void

all rights to warranty claims. The regional regulations on health protection and accident preven-

tion must be observed at all times and during all work on and with the product.

2.2.2 Safe Operating Condition

If circumstances occur which impair safety and cause changes in operating behavior, the product

must be shut down immediately and a ZEISS service representative should be informed.

The product may only be operated if the operating conditions are adhered to.

§Do not operate the product until you have completely read and understood the entire docu-

mentation.

§Ensure conditions and take measures to prevent the build up of electrostatic charge on the

workplace.

Instruction Manual ZEISS Axiocam 105 color | en-US | Rev.2 | 426555-7010-001 8

2 Safety | 2.3 Prevention of Hazards ZEISS

2.3 Prevention of Hazards

This product has been manufactured and tested by ZEISS according to the regulations specified in

CE and has left the manufacturer’s premises in perfect working order. The camera is intended to

be used in a basic electromagnetic environment while the noise emission conforms to CISPR 11

Class B level. The EMC performance might be impaired while integrated into a system. In order to

ensure that this condition is maintained and to avoid any risks when operating the system, the

user must comply with any notes and warnings contained in this manual. The manufacturer shall

be exempt from statutory liability for accidents should the operator fail to observe the safety regu-

lations.

CAUTION

Personal Injury

To avoid personal injury, read and adhere to the safety notes below.

4To avoid the risk of fire or explosion, do not use the camera near inflammable liquids or

gases.

4Setup, expansions, re-adjustments, alterations, and repairs must be carried out only by

persons who have been authorized by ZEISS.

4Do not allow any cables, particularly power cords, to trail across the floor, where they can

be snagged by people walking past.

4Protect the cables from excessive heat (e.g. halogen lamps, microscope fluorescence illu-

mination).

4To avoid injuries due to potentially high surface temperatures, do not touch the camera's

surface for a prolonged time.

4Do not position the equipment in a way that makes it difficult to operate or disconnect the

device.

NOTICE

To avoid equipment damage, data loss, or corrupted data, read and adhere to the safety notes

below.

4Protect the camera against mechanical impact. External damage may affect the operation

of inner components.

4Keep chemicals and fluids away from the camera.

4Make sure there is sufficient ventilation of the camera head. Avoid direct exposure to sun-

light and locations near heat sources (radiators, stoves). Overheating can cause noisy im-

ages.

4Use the camera in a clean and dry location.

4Attach all connectors firmly and securely.

4Use only the accessories supplied by ZEISS, when applicable.

4Use only normal microscope cleaning material to clean the camera housing.

4Contact your local ZEISS service organization if a repair is necessary. Do not disassemble

the camera by yourself, otherwise the warranty will be lost.

4Save all your data, such as images, measurement data, archives, reports, forms and docu-

ments, at regular intervals on an external storage medium. Otherwise it cannot be avoided

that access to this data may be lost as a result of operational errors or hardware defects.

ZEISS accepts no liability for consequential damage resulting from insufficient data protec-

tion.

Instruction Manual ZEISS Axiocam 105 color | en-US | Rev.2 | 426555-7010-001 9

3 Technical Data and Conformity | 3.1 Axiocam 105 color R2 ZEISS

3 Technical Data and Conformity

3.1 Axiocam 105 color R2

Feature Value

Sensor Type CMOS color sensor

Number of Pixels 2592 px x 1944 px (horizontal x vertical) = 5 megapixels

Pixel Size 2.2 μm x 2.2 μm

Chip Size 5.70 mm x 4.28 mm, corresponds to 1/2.24"

Live Image Frame Rate 2592 px x 1944 px (horizontal x vertical)

Frame rate @1 ms: 30 fps

Sensor Subarea Readout

(ROI)

Freely adjustable

Min. size: 864 px x 1 px (horizontal x vertical)

Digitization 8 Bit / pixel

Exposure Time 30 μs up to 1 s

Interface (camera) USB 3.0 Micro-B

Interface (PC / card) USB 3.0 Standard-A

Optical Interface C-Mount adapter

Dimensions 29 mm x 29 mm x 17.0 mm (height x width x depth)

Operating System Microsoft® Windows 10

Certificates CE, FCC Class B, RoHS

Power Supply Via USB 3.0 interface

USB Power 5 V, max. 400 mA

Environment Conditions 0° ... + 50° Celsius, max. 80% relative air humidity, no con-

densation, free air circulation required

Order Number 426555-9010-000

Info

Computer hardware, operating system and software may decrease the frame rates. Selecting a

part of the sensor area or applying binning can increase the frame rate. All specifications are

subject to change without notice.

Instruction Manual ZEISS Axiocam 105 color | en-US | Rev.2 | 426555-7010-001 10

Andere Handbücher für Axiocam 105 color

Inhaltsverzeichnis

Andere Zeiss Mikroskop Handbücher

Zeiss

Zeiss LSM 700 Bedienungsanleitung

Zeiss

Zeiss Primostar 3 Bedienungsanleitung

Zeiss

Zeiss OPMI Pentero Bedienungsanleitung

Zeiss

Zeiss JENA PLAN HD 9x12 Bedienungsanleitung

Zeiss

Zeiss LSM 700 Bedienungsanleitung

Zeiss

Zeiss HBO 100 Bedienungsanleitung

Zeiss

Zeiss Axioskop 2 FS plus Bedienungsanleitung

Zeiss

Zeiss LSM 900 Bedienungsanleitung

Zeiss

Zeiss Standard 25 ICS Bedienungsanleitung

Zeiss

Zeiss Axiolab Pol Bedienungsanleitung

Zeiss

Zeiss ELYRA Bedienungsanleitung

Zeiss

Zeiss Axio Vert.A1 Bedienungsanleitung

Zeiss

Zeiss LSM 710 Bedienungsanleitung

Zeiss

Zeiss VISU 200 Bedienungsanleitung

Zeiss

Zeiss Axio Observer Series Bedienungsanleitung

Zeiss

Zeiss Mechanical stage S mot. Bedienungsanleitung

Zeiss

Zeiss LSM 710 SIM Bedienungsanleitung

Zeiss

Zeiss IV FL Bedienungsanleitung

Zeiss

Zeiss OPMI PROergo S7 Bedienungsanleitung

Zeiss

Zeiss SV 6 Bedienungsanleitung

Zeiss

Zeiss LSM 900 Bedienungsanleitung

Zeiss

Zeiss SV8 Bedienungsanleitung

Zeiss

Zeiss Axio Zoom.V16 Bedienungsanleitung

Zeiss

Zeiss Axiocam MR Installations- und Betriebsanleitung

Beliebte Mikroskop Handbücher anderer Marken

Thermo Scientific

Thermo Scientific Nicolet iN10 Leitfaden

National

National DC3-163 Bedienungsanleitung

KERN Optics

KERN Optics OPE-1 Bedienungsanleitung

OPTIKA MICROSCOPES

OPTIKA MICROSCOPES B-150D Bedienungsanleitung

Prior

Prior Lux POL Bedienungsanleitung

Opitec

Opitec Smartscoop 115615 Bedienungsanleitung

KERN

KERN OPO-1 Bedienungsanleitung

Topcon

Topcon SP-1P Bedienungsanleitung

Motic

Motic PA43 Bedienungsanleitung

Leica

Leica DVM5000 Benutzerhandbuch

MshOt

MshOt MZ62 Bedienungsanleitung

KERN Optics

KERN Optics OZR-5 Bedienungsanleitung

VWR

VWR VisiScope 384 Series Bedienungsanleitung

Nikon

Nikon ECLIPSE E200 POL Bedienungsanleitung

Leica

Leica DI C800 Handbuch

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

ThermoFisher Scientific

ThermoFisher Scientific Continuµm Bedienungsanleitung

Olympus

Olympus SZ61 Bedienungsanleitung