ACME Dotline180 Bedienungsanleitung

CONTENTS

1. Safety Instructions ......................................................................................... 2

2. Technical Specifications ................................................................................. 4

3. How To Set The Unit....................................................................................... 5

3.1 Control Panel ........................................................................................... 5

3.2 Main Functions ........................................................................................ 7

3.3 Home Position Adjustment .................................................................... 15

4. Control By Universal DMX Controller ........................................................... 17

4.1 DMX512 Connection.............................................................................. 17

4.2 Address Setting ...................................................................................... 18

4.3 DMX512 Configurations ......................................................................... 18

5. Troubleshooting........................................................................................... 22

6. Fixture Cleaning ........................................................................................... 22

1. Safety Instructions

WARNING

Please keep this User Guide for future consultation. If you sell the unit to another user, be sure that

they also receive this instruction manual.

Important:

Damages caused by the disregard of this user manual are not subject to warranty. The dealer will

not accept liability for any resulting defects or problems.

Unpack and check carefully that there is no transportation damage before using the unit.

This product is for indoor use only. Use only in a dry location.

DO install and operate by qualified operator.

DO NOT allow children to operate the fixture.

Use safety chain when fixing the unit. Handle the unit by carrying its base instead of head only.

The unit must be installed in a location with adequate ventilation, at least 50cm from adjacent

surfaces.

Be sure that no ventilation slots are blocked, otherwise the unit will be overheated.

Before operating, ensure that the voltage and frequency of power supply match the power

requirements of the unit.

It’s important to ground the yellow/green conductor to earth in order to avoid electric shock.

Minimum ambient temperature TA: 0℃. Maximum ambient temperature TA: 40℃.

DO NOT connect the device to any dimmer pack.

Make sure there are no flammable materials close to the unit while operating to avoid fire

hazard.

Examine the power wires carefully; replace them immediately if there is any damage.

Unit’s surface temperature may reach up to 60℃. DO NOT touch the housing bare-handed

during its operation.

Avoid any inflammable liquids, water or metal objects entering the unit. Once it happens, cut

Please read the instruction carefully which includes important information about

the installation, usage and maintenance.

off the mains power immediately.

DO NOT operate in dirty or dusty environment, do clean fixtures regularly.

DO NOT touch any wire during operation as there might be a hazard of electric shock.

Avoid power wires together twist other cables.

The minimum distance between light output and the illuminated surface must be more than

0.5 meters.

Disconnect mains power before fuse replacement or servicing.

Replace fuse only with the same type.

In the event of serious operating problem, stop using the unit immediately.

Never turn on and off the unit time after time.

The housing, the lenses, or the ultraviolet filter must be replaced if they are visibly damaged.

DO NOT open the unit as there are no user serviceable parts inside.

Never try to repair the unit by yourself. Repairs carried out by unskilled people can lead to

damage or malfunction. Please contact the nearest authorized technical assistance center if

needed.

Disconnect the mains power if the fixture is has not been used for a long time.

DO use the original packing materials before transporting it again.

DO NOT look directly at the light while the LED is on.

DO NOT start on the unit without LED enclosure or when housing is damaged.

Installation:

The fixture should be mounted via its Omega Quick Release Clamp bracket. Always ensure that the

unit is firmly fixed to avoid vibration and slipping while operating and make sure that the structure

to which you are attaching the unit is secure and is able to support a weight of 10 times of the

fixtures weight. Always use a safety cable that can hold 12 times of the weight of the fixture when

installing.

The equipment must be installed by professionals. It must be installed in a place where is out of the

reach of people and no one can pass by or under it.

2. Technical Specifications

Power Voltage:

AC 100~240V, 50/60Hz

Power Consumption:

240W

Light Source:

6x40W RGBW LED

Zoom Range:

3.5°~38°

Movement:

Tilt: 220°

Dimmer/Shutter:

0~100% smooth dimming, adjustable strobe speeds

Control:

DMX Channel: 32/14 Channels

Control Mode: DMX512, RDM, Art-Net

Firmware Upgrade: Update via DMX link

Construction:

Display: OLED display

Data In/Out: 3-pin or 5-pin XLR, RJ-45

Power In/Out: Power Connector in/out

Protection Rating: IP20

Features:

The led pitch is the same between 2 fixtures once connected with shafts

Linear motorized zoom

Outstanding color mixing effect

Dimension/Weight:

500x113x278mm, 10.7kgs

19.7"x4.4"x10.9"in, 23.6lbs

278mm

500mm

113mm

3. How To Set The Unit

3.1 Control Panel

1. Button:

MENU To select the programming functions

UP To go backward in the selected functions

DOWN To go forward in the selected functions

ENTER To confirm the selected functions

2. Display: To show the various menus and the selected functions

3. OFFLINE SETTING: To show the battery status

4. POWER IN:

To connect to the mains supply

5. POWER OUT:

To connect to the next unit

6. ETHERNET:

Transfers fixture’s information to a main controller

7. DMX OUT:

For DMX512 operation, use 5-pin XLR cable to output DMX signal (3-pin XLR is optional)

8. DMX IN:

For DMX512 operation, use 5-pin XLR cable to input DMX signal (3-pin XLR is optional)

9. Firmware Upgrade

Used to upgrade fixture’s firmware

10. FUSE(T 5A):

Protect the unit from damage of the overcurrent

11. PUSH BUTTON 1 (Head Push Button):

Before the fixture is powered on, please push the button to “UNLOCK” of the head

12. PUSH BOTTON 2:

When the fixture is online, please push the button to “LOCK”

3.2 Main Functions

Turn on the unit, press the MENU button into menu mode, and press the UP/DOWN button until

the required function is shown on the monitor. Select the function by the ENTER button. Use the

UP/DOWN button to choose the submenu, press the ENTER button to store and automatically

return to the last menu. Press the MENU button or let the unit idle 30 seconds to exit menu mode.

The screen will be automatically locked if there is no operation for a long time, and can be unlocked

by long-pressing the MENU button.

The main functions are shown below:

DMX Setting

To select DMX Setting, press the ENTER button to confirm, use the UP/DOWN button to select

ArtNet Setup, DMX Address, Channel Mode or RDM Device ID.

ArtNet Setup

To select ArtNet Setup, press the ENTER button to confirm. Use the UP/DOWN button to select

Ethernet IP Setup or ArtNet Port Setup, press the ENTER button to store. When choose Ethernet IP

Setup, use the UP/DOWN button to select IP Address or Subnet Mask. When choose Art-Net Port

Setup, use the UP/DOWN button to select Net, Subnet or Universe. Press the MENU button back to

the last menu or let the unit idle 30 seconds to exit menu mode.

DMX Address

To select DMX Address, press the ENTER button to confirm. Use the UP/DOWN button to adjust the

address from 001 to 481/499, press the ENTER button to store. Press the MENU button back to the

last menu or let the unit idle 30 seconds to exit menu mode.

Channel Mode

To select Channel Mode, press the ENTER button to confirm. Use the UP/DOWN button to select 32

CH or 14 CH, press the ENTER button to store. Press the MENU button back to the last menu or let

the unit idle 30 seconds to exit menu mode.

RDM Device ID

To select RDM Device ID, press the ENTER button to confirm, it will show the RDM Device ID. To go

back to the functions without any changes press the MENU button.

DMX Last State

To select DMX Last State, press the ENTER button to confirm. Use the DOWN/UP buttons to select

Black Out, Hold or Manu, press the ENTER button to store. Press the MENU button back to the last

menu or let the unit idle 30 seconds to exit menu mode.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ACME Beleuchtungsausrüstung Handbücher

ACME

ACME LED-245/2 Bedienungsanleitung

ACME

ACME LP-1600 BD30 Bedienungsanleitung

ACME

ACME Thunderbreaker Bedienungsanleitung

ACME

ACME Spartan Hybrid Bedienungsanleitung

ACME

ACME BF-1500ND B Bedienungsanleitung

ACME

ACME LED-3082 RGB Bedienungsanleitung

ACME

ACME FLASHDOT Bedienungsanleitung

ACME

ACME BW-54-10FC II RL Bedienungsanleitung

ACME

ACME Sandane Bedienungsanleitung

ACME

ACME GLAMOUR 700Z RGBY Bedienungsanleitung

ACME

ACME Theatre Spot 150m Bedienungsanleitung

ACME

ACME MP-12FC Bedienungsanleitung

ACME

ACME ANIMA C Bedienungsanleitung

ACME

ACME Diamonds II Bedienungsanleitung

ACME

ACME Solar Flare Bedienungsanleitung

ACME

ACME Xperior 1500SZ Bedienungsanleitung

ACME

ACME XP-5000WZ Bedienungsanleitung

ACME

ACME Beluga Bedienungsanleitung

ACME

ACME BTDG40 Bedienungsanleitung

ACME

ACME Xperior 700SZ Spot Bedienungsanleitung

ACME

ACME SABER Mini Bedienungsanleitung

ACME

ACME Uploader II Bedienungsanleitung

ACME

ACME Sunrise Bedienungsanleitung

ACME

ACME TOUR PIXEL BAR 1010 II Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung