Assa Abloy Norton 6000 Series Installationshandbuch

80-9360-1043-020 Rev 1 05/21

6000 Series Full Feature Low Energy Operator

Single Door Installation

Programming Instructions

Onboard or Wi-Fi Smart Device

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

These programming instructions guide setup of the 6000 operator installed

on a single door via the onboard LCD screen or a Wi-Fi smart device.

Pour la version francaise voir www.nortondoorcontrols.com.

READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.

This product can expose you to lead which is known to the state of

California to cause cancer and birth defects or other reproductive harm.

For more information go to www.P65warnings.ca.gov.

WARNING

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions

Contents

Initial Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Onboard Programming Method .............................................................................. 5

Wi-Fi Programming Method .................................................................................. 9

Input Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Output Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Error Code Chart and Status Denitions......................................................................15

To Update 6000 Wi-Fi Inverter ...............................................................................16

Wiring Diagrams

Basic Single Door Using Factory Presets ......................................................................17

Hard Wired Push Button.....................................................................................18

Wave to Open...............................................................................................19

RF Standard .................................................................................................20

Fail Secure Electric Strike . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Fail Safe Electric Strike .......................................................................................22

Electric Dogging Exit Device .................................................................................23

MKA2 x 24V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Electric Latch Retraction Powered Through 782N Controller .................................................25

Electric Latch Retraction Smoke Ventilation..................................................................26

Hard Wired Executive Function ..............................................................................27

RF Executive Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

433MHz Receiver User’s Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Vestibule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

585 Presence Detector on Standard Opening................................................................31

596 Presence Detector on Single Door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Troubleshooting Guide......................................................................................33

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions

FCC:

Class B Equipment

This equipment has been tested and found to comply with the limits

for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against

harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television

reception, which can be determined by turning the equipment off

and on, the use is encouraged to try to correct the interference by one

or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not cause

harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Warning:

Changes or modications to this device may void the user’s authority

to operate the equipment.

Industry Canada:

This Class A digital apparatus meets all requirements of the

Canadian Interference Causing Equipment Regulations.

Cet appareillage numérique de la classe A répond à toutes les

exigences de l’interférence canadienne causant des règlements

d’équipement.

Declaración de México:

La operación de este equipo está sujeta a las siguientes dos

condiciones: (1) es posible que este equipo o dispositivo no cause

interferencia perjudicial y (2) este equipo o dispositivo debe

aceptar cualquier interferencia, incluyendo la que pueda causar su

operación no deseada.

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions

1. With building power feed turned off, route

120VAC wiring through conduit holes in back

plate for concealed wiring or through the Union

Assembly knock-out for surface wiring and

connect conduit to Conduit Assembly.

2. Connect 120VAC power to terminal strip on top

of Conduit Assembly: HOT to “+”, NEUTRAL to

“-”, and GROUND to green ground screw.

(Figure 1)

NOTE: Union Assembly may need to be

removed for ease of access. Remove AND SAVE

(4) 8-32 x 5/16" Philips pan head screws.

3. Wire in any devices needing outputs, such as

electric strikes, mag locks, exit devices, door

open position output, etc to green terminals on

top of control board. (Figure 2)

4. Reinstall Union Assembly using (4) 8-32x5/16"

screws previously removed.

5. Turn on building power to unit.

6. Conrm ON/OFF/HO switch is in ON position

before proceeding to Setup. (Figure 3)

NOTE: On control board there should be one

solid red LED for POWER and one white LED

that flashes every 1.5 - 2 seconds for STATUS.

CLOSE button of Setup Buttons should be

flashing orange continuously.

NOTE: If red LED is flashing, refer to

Troubleshooting section of this manual or

contact Technical Product Support.

Initial Wiring

Conduit Hole

Terminal Strip

Figure 1

Figure 2

Figure 3

Shown in

ON Position

Door Setup

REQUIRED GO

Status LED

Input Terminals

WARNING: Door may begin to move immediately

when selector mode switch is changed. An open

union assembly door has potential to pinch fingers

if hand is not withdrawn quickly when adjusting

selector mode switch. There is also potential of

damaging or breaking door if door is open during

closing cycle of a pull side assembly.

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions: Onboard Method

Select arm type.

1. Select GO from the Door Setup REQUIRED menu

by pushing joystick to the right. (Figure 4)

2. Depending on your application, select PUSH or

PULL by moving joystick LEFT or RIGHT. (Figure 5)

Figure 6

Figure 5

Door Mode

PULL

Figure 4

Door Setup

REQUIRED GO

Setup Using LCD Screen

PULL:

6011 PULL 110°

Select operator model.

1. After setting arm type, push joystick UP to select

operator model.

2. Select specic operator model by pushing joystick

LEFT or RIGHT. (Figure 6)

Pull: (Figure 7)

6011 PULL 110 deg

6051 PULL 110 deg

PUSH: (Figure 8 or Figure 9)

6021 PUSH 110 deg

6031 PUSH 110 deg

6061 PUSH 85 deg

6061 PUSH 90 deg

6061 PUSH 95 deg

6061 PUSH 100 deg

6061 PUSH 105 deg

6061 PUSH 110 deg

6071 PUSH 85 deg

6071 PUSH 90 deg

6071 PUSH 95 deg

6071 PUSH 100 deg

6071 PUSH 105 deg

6071 PUSH 110 deg

3. Push joystick UP.

Follow these steps after operator has been

successfully installed and power has been turned on

(see Page 4, Initial Wiring):

PULL: 6011 or 6051

PUSH: 6021 or 6031

PUSH: 6061 or 6071

Figure 7

Figure 8

Figure 9

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions: Onboard Method

Set door open and door closed positions.

1. To set closed position, fully close door. Press and

release CLOSE button on board. Flashing ORANGE

LED should turn solid. (Figure 10)

NOTE: Any time door is in closed position, orange

LED should be solid.

2. GREEN OPEN LED should now be ashing.

3. To set the fully open position, manually open door to

open position and hold door there.

NOTE: If there is a wall or door stop at open

position, hold door slightly away from wall or stop.

4. Press and release OPEN button on board. Flashing

GREEN OPEN LED should turn solid. Let door close.

(Figure 11)

NOTE: Any time door is in open position, green LED

should be solid.

NOTE: If open position is not set within 30 seconds

of setting closed position, closed position must set

again.

NOTE: Once door has fully closed, make sure there

are no obstructions that could prevent door from

opening. Latching hardware must not prevent

door from opening during following step.

5. Operator must now learn its internal settings. Press

and release LEARN button on board. BLUE LEARN

LED will start ashing and door will open in small

increments. Allow door to open and close without

interference. (Figure 12)

NOTE: After operator has learned settings, if spring

is adjusted or accessories are attached to door that

would make door heavier, operator MUST relearn

internal settings by repeating step 5.

6. Once setup is complete, use Open Pos Adjust setting

to gain up to an additional 5 degrees of opening.

Figure 10

Open Door and

Push OPEN Button

Close Door and

Push CLOSE Button

Close Door and

Push LEARN Button

Figure 11

Figure 12

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions: Onboard Method

Adjust opening and closing.

Using joystick, make selections to adjust

electrical opening and closing of door.

(Figure 13)

NOTE: Latch, Sweep, and Backcheck

valves were adjusted during initial

installation so unit functions properly

as a mechanical door closer. See

Installation Instructions for your

model.

Figure 13

Open Speed

6: iiiiii----

Speed/Force and Timing/Location

settings must be adjusted to meet

ANSI BHMA A159.19 (American

National Standard for Power Assist and

Low Energy Power Operated Doors)

requirements for opening and closing

based on door weight and width. (See

tables below)

Note: To determine minimum times from close to full open, the operator shall be adjusted as shown in the chart. Backcheck occurring at a point

between positions in Table II shall use the lowest setting. For example, if the backcheck occurs at 75 degrees, the full open shall be the time shown in

Table I plus 1.5 seconds.

Doors of other weights and widths can be calculated using the formula:

T = D ÖW/ 133 in US Units T = D ÖW/ 2260 in SI (metric) Units

Where: T = Time, seconds

D = Door width, inches (mm)

W = Door weight, lbs. (kg)

The values for “T” time have been rounded up to the nearest half secound. These values are based on a kinetic energy of 1.25 lbf-ft.

Table I

Minimum Opening Time to Backcheck or 80 degrees (whichever occurs rst) and

Minimum Closing Time from 90 degrees to Latchcheck or 10 degrees (whichever occurs rst)

“D” Door Leaf Width

Inches (mm)

“W” Door Weight in Pounds (kg)

100 (45.4) 125 (56.7) 150 (68.0) 175 (79.4) 200 (90.7)

*30 (762) 3.0 3.0 3.0 3.0 3.5

36 (914) 3.0 3.5 3.5 4.0 4.0

42 (1067) 3.5 4.0 4.0 4.5 4.5

48 (1219) 4.0 4.5 4.5 5.0 5.5

* Check applicable Building Codes for clear width requrements in the Means of Egress. See Appendix for additional door weights.

Table II: Total Opening Time to 90 Degrees

Backcheck at 60 degrees Backcheck at 70 degrees Backcheck at 80 degrees

Table I plus 2 seconds Table I plus 1.5 seconds Table I plus 1 second

If the door opens more than 90 degrees, it shall continue at the same rate as backcheck speed. Matrix values are in seconds.

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions: Onboard Method

• OPEN SPEED: Speed at which door opens.

• MAX OPEN FORCE: Force exerted by motor to open door.

• OPEN START FORCE: Force exerted by motor at start of

opening cycle to help overcome stack pressure or latch device.

• OPEN STALL FORCE: Force exerted when door is slowed to

a stop while opening, with 1 being lightest and 10 being

strongest. Measure door force to ensure compliance with

standards and codes.

• ADJUST HOLD OPEN: Time door is held at open position when

ON/OFF/HO switch is in ON position.

• HOLD OPEN FORCE: Force exerted to hold door in max open

position. Can be adjusted to overcome stack pressure, wind, or

other forces pushing on door.

• OBST DET SENS: Amount of time door will push against an

obstruction before stalling or moving in opposite direction.

• OPEN DELAY 1: Time before door will begin to open once

activation has been received.

Set options.

Using joystick, set options. (Figure 14)

Continue with Input Connections on page 13

Figure 14

Max Open Force

• OPEN DELAY 2: Time before door will begin to open once

activation has been received. Part of Vestibule functionality.

• PUSH & GO: As door is manually opened, operator ‘senses’

movement and opens door to full-open position.

• OBSTR DURING CLOSE: Door will reverse to open position if

it hits an obstruction while closing.

• NO OBSTR NEAR OPEN: Used with door mounted presence

sensor. Operator will ignore obstruction input from sensor

in last 30 degrees of opening.

• NO OBSTR NEAR CLOSE: Used with door mounted presence

sensor. Operator will ignore obstruction input from sensor

in last 10 degrees of closing.

• ENERGIZE <20°: 24V outputs will change state when door is

20 degrees from close after a manual or automatic cycle.

• AUDIBLE BEEP: Turn audible beep feedback from interface

PCB off/on.

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions: Wi-Fi Method

Shown in

ON Position

Follow these steps after operator has been

successfully installed and power has been turned on

(see Page 4, Initial Wiring):

1. Turn on Operator Wi-Fi

With cover off:

Using joystick, scroll to Wi-Fi Link menu on LCD

screen. Select ON by pushing joystick RIGHT or

LEFT. Red LED indicates ON. (Figure 15)

With cover on:

Toggle 3 Position switch on end cap 3 times.

(Figure 16)

NOTE:

• Operator will emit a long beep when Wi-Fi

has been successfully turned on.

• Wi-Fi automatically turns off after 20 minutes

of inactivity.

• For further security, Wi-Fi can be turned off

immediately by selecting OFF on LCD screen

or toggling 3 Position switch again. Operator

will emit a short beep when Wi-Fi has been

successfully turned off.

• Operator serial number, password and IP

address are located inside 3 Position switch

door. (Figure 17)

2. From your smart device open Wi-Fi Networks to

search for operator SSID. Once your specic ID

beginning with NDC6000_ is found, connect to

network.

3. Enter operator password.

4. From your web browser, enter 192.168.1.1 into

search bar.

5. The 6000 Series Operator homepage is indication

of a successful connection. (Figure 18)

Figure 15

WiFi Link

ON (192.168.1.1)

BEEP

Toggle

OFF/ON

Figure 16

Figure 17

Setup Using Wi-Fi

Figure 18

Serial Number

Password

IP Address

80-9360-1043-020 Rev 1 05/21

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

6000 Series Programming Instructions: Wi-Fi Method

Status

Use Status page to quickly access important

information about your operator.

NOTE: “Door Setup Needed” will be displayed if

door setup has not been completed.

Setup

To set up your operator, select Setup page and

proceed through four steps.

1. Select “Operator Model and Opening Range”

that matches your installation.

2. Manually close door and select “Set Closed

Position”.

3. Open door to fully open position. While

holding door open, select “Set Open

Position”.

4. Close door completely and select “Learn” to

perform Learn process.

NOTE: Door will automatically move

through an opening cycle. Be sure there is

no obstruction.

5. Refresh browser page to conrm all

steps have indicating setup has been

successful.

✓✓

Andere Handbücher für Norton 6000 Series

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy RIXSON W91DCP Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7900H-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy RD150-3 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7200 Series Kurzanleitung

Assa Abloy

Assa Abloy Sargent 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 1331 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600H Series Bedienungsanleitung

Assa Abloy

Assa Abloy King 70 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130-HU Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy DC135 Service-Handbuch

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED4000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Besam VersaMax ICU Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent FIREGUARD 2408 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 UniTrol Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung