Assa Abloy SARGENT 351 POWERGLIDE Series Bedienungsanleitung

LEFT

HAND DOOR

RIGHT

HAND DOOR

PULL

HINGE SIDE

PULL

HINGE SIDE

STOP (PUSH) SIDE STOP (PUSH) SIDE

STANDARD APPLICATION

(TYPE 25-O ARM)

TOP JAMB

APPLICATION

(TYPE 25-O, 25-OZ

AND 25-OZA ARMS)

PARALLEL ARM

APPLICATION

(TYPE 25-P9)

CLOSER MOUNTED ON

HINGE SIDE OF DOOR

CLOSER MOUNTED ON

STOP SIDE OF DOOR

CLOSER MOUNTED ON FRAME

ON STOP SIDE OF DOOR

NOTE: FOR 08 AND OLC TYPE ARMS MOUNTING

SEE DATA SHEETS ENCLOSED

NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREW

FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)

DOOR WIDTH

(INCHES)

OVER 48

351

EXTERIOR DOORS

FACTORY SET

1-4 CW

4-7 CW

7-10 CW

10-12 CW

UP TO 18 CW AS REQ.

INTERIOR DOORS

1-5 CCW

FACTORY SET

1-5 CW

5 CW AND UP AS REQ.

APPROXIMATE

DOOR WEIGHT (POUNDS)

110

115

130

150

155

165

170

180

NUMBER OF TURNS OF SPRING POWER ADJUSTING NUT

FROM FACTORY SETTING (USE CHART AS GUIDE ONLY)

DOOR WIDTH

(INCHES)

OVER 48

351

EXTERIOR DOORS

2-6 CW

6-8 CW

8-11 CW

11-13 CW

UP TO 18 CW AS REQ.

INTERIOR DOORS

1-5 CCW

FACTORY SET

1-7 CW

8 CW AND UP AS REQ.

APPROXIMATE

DOOR WEIGHT (POUNDS)

110

115

130

150

155

165

170

180

ADJUST SPRING POWER ACCORDING TO CHART*

INCREASE

POWER

CLOCKWISE

(CW)

DECREASE

POWER

COUNTER CLOCKWISE

(CCW)

*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGS

ARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNING

SPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREW

COUNTERCLOCKWISE.

5/8" SPRING POWER

ADJUSTMENT NUT

USE

PAGE 2

USE

PAGE 3

USE

PAGE 4

A7340C

Sargent Manufacturing Company is prohibited.

MODEL 351 POWERGLIDE SERIES

INSTRUCTIONS FOR INSTALLING SARGENT DOOR

CLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)

351 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6

CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.

FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.

STANDARD & TOP JAMB APPLICATIONS

PARALLEL APPLICATION ONLY

351 STANDARD ARM APPLICATION INSTRUCTIONS

INSTALL DOOR CLOSER TO DOOR WITH

SPRING ADJUSTMENT NUT AWAY FROM HINGE.

NOTE: 351 CLOSER BODIES ARE NON HANDED.

IT IS IMPORTANT THAT THE CLOSER BODY BE

MARKED WITH “RH” SYMBOL AT TOP, FOR RIGHT

HAND DOORS. “LH” SYMBOL AT TOP FOR LEFT

HAND DOORS.

ATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW AND

WASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.

ATTACH FOOT TO FRAME WITH PIVOT

AWAY FROM HINGE.

RIGHT HAND

DOOR SHOWN

DIM. "B"

DIM. "A"

ALTERNATE

STANDARD 8 3/16"

6 13/16"

11 7/16"

10 1/16"

MOUNTING

120∞

DIM.

MAX. DOOR

OPENING

IMPORTANT: USE ALTERNATE MOUNTING IF DOOR CAN

OPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTING

IF BUTT, FRAME AND WALL CONDITIONS PERMIT DOOR WILL

OPEN 180°

160∞

ARM

TYPE

REGULAR

ARM NO

HOLDER

RIGHT HAND DOOR SHOWN. LEFT HAND

DOOR OPPOSITE.

2THIS DIMENSION IS TAKEN FROM HINGE

EDGE OF DOOR FOR INVISIBLE HINGES.

C OF HINGE PIVOT: BUTTS, OFFSET PIVOTS,

SWING CLEAR, CENTER HUNG OR INVISIBLE HINGES

#12 x 3 WOOD SCREWS OR

#12-24 X 2 1/4 FLAT HEAD

MACHINE SCREWS

SEE PAGE 6 FOR MORTISE NUTS

90°

RIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)

ROD

ARM

SCREW

SWIVEL ARM

POSITION OF

MAIN ARM WHEN

ASSEMBLING

TO SPINDLE

INDEX MARK

ON SPINDLE

MAIN ARM

DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE

NUTS WHEN REQUIRED.

USE TEMPLATE A6753 FOR 25-OLC ARM

(LOW PROFILE)

PIVOT

2 1/2"

9/16"

1 1/8"

TOP OF DOOR

B C

A7340C

Sargent Manufacturing Company is prohibited.

351 TOP JAMB APPLICATION INSTRUCTIONS

INSTALL DOOR CLOSER TO FRAME WITH SPRING

ADJUSTMENT NUT AWAY FROM HINGE.

INSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN.

OPEN DOOR INSERT RETANGULAR ROD INTO SWIVEL

ARM THEN CLOSE THE DOOR AND TIGHTEN ARM SCREW SECURELY WHEN SWIVEL ARM IS AT RIGHT ANGLE TO DOOR.

ATTACH FOOT TO DOOR WITH

PIVOT AWAY FROM HINGE.

RIGHT HAND

DOOR SHOWN

NOTE: 351 CLOSER BODIES ARE NON HANDED.

IT IS IMPORTANT THAT THE CLOSER BODY BE

MARKED WITH “RH” SYMBOL AT TOP, FOR LEFT

HAND DOORS. “LH” SYMBOL AT TOP FOR RIGHT

HAND DOORS.

RIGHT HAND DOOR SHOWN,

LEFT HAND DOOR OPPOSITE.

THIS DIMENSION IS TAKEN FROM HINGE

EDGE OF DOOR FOR INVISIBLE HINGES.

140°

110°

MAX.

DOOR OPENING

DIM.

5 3/8"

8 5/8"

DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISE NUTS WHEN REQUIRED.

DOOR OPENING TO 180∞ IS POSSIBLE IF

DEPTH OF REVEAL IS NOT GREATER THAN 2"

ROD

ARM

SCREW

SWIVEL ARM

POSITION OF

MAIN ARM WHEN

ASSEMBLING

TO SPINDLE

LEFT HAND DOOR

FOOT PIVOT

90°

FOOT PIVOT

RIGHT HAND DOOR

POSITION OF

MAIN ARM WHEN

ASSEMBLING

TO SPINDLE

ROD

ARM

SCREW

SWIVEL ARM

90°

DEPTH OF REVEAL

DOOR

DEPTH OF REVEAL

SINGLE

RABBETED

FRAME

TOP OF DOOR

DOUBLE RABBETED

FRAME WITH REQUIRED

MOUNTING PLATE

351-A MOUNTING

PLATE

FRAME

1/4"

3 1/4"

1 1/2" 6"

5/8"

STOP

MAX 351-A PLATE

7/16"

C OF PIVOT HINGE

DIM A

#12 X 1 1/2"

WOOD SCREWS OR

#12-24 X 5/8"

FLAT HEAD

MACHINE SCREW

FRAME

STOP

1 3/4" MIN

7/16"

PROVIDE 5/16" DIAMETER CLEARANCE

HOLES IN FRAME FOR CLOSER SCREWS

WHICH PROJECT 5/16" BEYOND PLATE3 1/2" 2 1/2"

13/16"

2 1/4"

HINGE

SIDE

MAIN

ARM INDEX

MARK

SPINDLE

VIEW LOOKING UP

WHEN ASSEMBLING

ARM TO SPINDLE

SEE PAGE 6 FOR

MORTISE NUTS

2 1/8" TO 5"

0" TO 2"

REVEAL

DEPTH

ARM

TYPE

140°

DOOR

OPENING

140°

“OZ” ARM

“O” ARM

5 1/8" TO 8" 140°

“OZA” ARM

A7340C

Sargent Manufacturing Company is prohibited.

351 PARALLEL ARM APPLICATION INSTRUCTIONS

INSTALL DOOR CLOSER TO DOOR WITH SPRING ADJUSTMENT

NUT AWAY FROM HINGE.

ATTACH FOOT BRACKET TO FRAME STOP.

OPTIONAL ARMS FOR MOUNTING. SEE DATA

SHEET ENCLOSED.

9 7/8" 10 1/4"

7 3/8"

120°

DIM.

MAX. DOOR

OPENING

180°

TOP OF

DOOR

STOP

C OF HINGE PIVOT

DIM. A

TOP VIEW

1 1/4"

2 1/2"5/16"

7/8"

1/2"

DOOR

C OF HINGE PIVOT

(BUTT HINGE SHOWN)

FOR USE WITH

OVERHEAD

DOOR HOLDERS

P4 OR P4A

BRACKET

FOR FLUSH FRAME

AND DOOR CONDITIONS

P4A BRACKET IS USED

WITH OVERHEAD HOLDERS

P3 OR P3A

BRACKET

(SARGENT

#590 SHOWN)

DIM. B

2 3/8"

2 1/2"

#12 WOOD SCREWS

OR #12-24 x 5/8 FLAT HEAD

MACHINE SCREWS

RIGHT HAND

DOOR SHOWN

USING WRENCH ON BOTTOM END OF SPINDLE, ROTATE SPINDLE 45∞ AND ASSEMBLE

MAIN ARM TO CLOSER AS SHOWN, AND THEN INSERT ROD END INTO SWIVEL ARM AND

TIGHTEN ARM SCREW POSITIONING ARM 1 1/2" AWAY FROM DOOR.

#12 X 3" WOOD SCREWS

OR #12-24 X 2 1/4"

MACHINE SCREW

SEE PAGE 6 FOR

MORTISE NUTS

CAUTION: DOOR CLOSER

WILL NOT OPERATE

PROPERLY IF ARM IS NOT

INDEXED CORRECTLY.

LEFT HAND VIEW OF INDEX

45° PRELOAD

APPROX. 50°

POSITION OF MAIN ARM

WHEN ASSEMBLINGTO SPINDLE

RIGHT HAND

DOOR

FOOT BRACKET

ARM SCREW

MAIN ARM

ROD

1 1/2"

INDEX MARK

ON SPINDLE

MAIN ARM

INDEX MARK

ON SPINDLE

RIGHT HAND VIEW OF INDEX

45°

MAIN

ARM

LEFT HAND DOOR SHOWN. RIGHT HAND

DOOR DIMENSION OPPOSITE.

2DO NOT USE THIS MOUNTING FOR

“SWING CLEAR” HINGES.

3THIS DIMENSION IS TAKEN FROM HINGE

EDGE OF DOOR FOR INVISIBLE HINGES.

DRILL & TAP AND USE SCREWS PROVIDED OR USE

MORTISE NUTS WHEN REQUIRED.

NOTE: 351 CLOSER BODIES ARE NON HANDED.

IT IS IMPORTANT THAT THE CLOSER BODY BE

MARKED WITH “RH” SYMBOL AT TOP, FOR RIGHT

HAND DOORS. “LH” SYMBOL AT TOP FOR LEFT HAND DOORS.

A7340C

Sargent Manufacturing Company is prohibited.

FINAL ADJUSTMENT AND REGULATING PROCEDURE

A B

REGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.

USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES

CLOCKWISE TO SLOW DOWN OR COUNTER CLOCKWISE TO

SPEED UP DOOR MOVEMENT.

INSTALL COVER WITH TWO SCREWS AS SHOWN.

FOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE

“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGH

DELAYED ACTION RANGE

TURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTER

CLOCKWISE TO SPEED UP DOOR MOVEMENT

REGULATING BACKCHECK

TO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVE

CLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASE

CHECKING.

CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT IS

DAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.

NEVER USE BACKCHECK AS A DOOR STOP.

ALWAYS USE A DOOR STOP TO STOP THE DOOR.

ADJUSTING FOOT FOR ADDITIONAL CLOSING POWER

(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)

HINGE EDGE OF DOOR

MOVE FOOT

PIVOT TO HOLE

NEAREST HINGE

DELAYED ACTION

RANGE

CLOSING SPEED

RANGE

LATCHING

SPEED RANGE

BACKCHECK

RANGE

BACKCHECK

VALVE

OPTIONAL DELAYED

ACTION VALVE

DOOR SPEED

VALVE

LATCHING

SPEED VALVE

INSERT IS REMOVABLE.

PLACE IN UNUSED OPENING.

FASTER

(+)

SLOWER

(–)

A7340C

Sargent Manufacturing Company is prohibited.

USING MORTISE NUTS WITH SARGENT DOOR CLOSER

1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING

THE CLOSER BODY AND FOOT ON DOOR AND FRAME.

2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.

4. FOR DOORS 2 1/4" THICK: MORTISE NUT SHOWN FOR 1 3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.

DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTS

ARE TIGHTENED.

3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THAT

SHOWN FOR MOUNTING THE CLOSER BODY.

FRAME

VIEW "Y"

DOOR

1/8"

5/8" DIA. HOLE

SHORTEN MORTISE

NUT BODY TO

THIS LENGTH

1/4" DIA.

DRILLED HOLE

DOOR CLOSER SHOWN

(TRACK ASSEMBLY

MOUNTING IS SIMILAR)

3/8" DIA. HOLE

MORTISE NUT

HEAD

DOOR

STOP

9/16"

DIA.

7/64"

MORTISE NUT

1 11/16" FOR 1 3/4" THICK DOOR

1 5/16" FOR 1 3/8" THICK DOOR

(SEE NOTE #4 FOR 2 1/4" THICK DOORS)

#12-24 THREAD

FRAME

DOOR

COVER

SARGENT 1430

SERIES CLOSER

SHOWN. (OTHER

SERIES SIMILAR)

DOOR STOP

MORTISE NUT HEAD

DRILL 3/8" DIA.

HOLE FOR MORTISE

NUT BODY.

DRILL 1/4" DIA. HOLE

FOR MOUNTING SCREWS

SARGENT 351 SERIES SHOWN

SEE NOTE #1 BELOW FOR DIMENSION

INFORMATION. IF A DIMENSION LESS THAN

7/8" IS USED. THE DOOR STOP MUST BE CUT

TO CLEAR THE MORTISE NUT HEAD OR THE

MORTISE NUT HEAD MUST BE RECESSED.

(SEE ENLARGED VIEW "Y")

A7340C

Sargent Manufacturing Company is prohibited.

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Corbin Russwin DC6210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 6000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5700 Series Kurzanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5700 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1130-HU Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy ABLOY DA401 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton PR1601 Bedienungsanleitung

Assa Abloy

Assa Abloy RD3 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9510 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood L7714SDSIL Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5400 FE Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 8000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7970DPS-B Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-FMS Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin DC8210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-CO-C Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 2409 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton SafeZone 7110SZ Kurzanleitung

Assa Abloy

Assa Abloy SARGENT FIREGUARD 12-2468 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung