Assa Abloy Norton LEO 5700 Series Bedienungsanleitung

These instructions are used to change the application of a LEO

operator from a Push Side unit to a Pull side unit.

80-9357-0140-020 (09-10)

5700 LEO Power Operator Conversion

Push to Pull / Pull to Push Application

80-9357-0140-020 (09-10)

Patents: 5,881,497; 7,316,096; 7,484,333

1. The unit shown in fig.1 is configured for a push side application.

Note the valve orientation of the closer body. The photo in fig.2

shows a close-up view of the clutch mechanism configured for

push side application.

2. Remove the four screws which secure the closer body to the

backplate.

3. Slide the closer body away from the clutch assembly and chain.

Make sure you do not remove pinion extension when removing

closer body from clutch mechanism.

4. Orient the closer body as shown in fig. 3, with “BC” valve toward

conduit holes, and slide onto backplate so that closer pinion is

inserted into pinion extension. Some rotational adjustment of the

pinion extension may be required to allow assembly of closer

pinion and pinion extension.

5. Replace and tighten closer body screws removed in step 2. See

fig. 4.

6. Flip the dip switch on the inverter from the Push to the Pull

position, see fig. 5.

Instructions continued on page 2.

Fig.1

Sweep & Latch

Valves

Pinion

Extension

Cam

Driver

Fig.3

Fig.4

Fig.2

Fig.5

Push/Pull Dip Switch

280-9357-0140-020 (09-10)

9. With door closed, slide Closed Position Magnet so it aligns with

the Reed Switch. See fig. 8.

10. Slide Open Position Magnet so it is 180° from the Reed Switch.

See fig. 9. Slide Open Position Magnet as needed to get proper

door opening.

11. Continue to page 4.

Fig.8

Closed Position

Magnet

Reed Switch

Fig.9

Open Position

Magnet

Reed Switch

7. Verify switch is in the “ON” position for the circuit breaker and

activate unit.

8. Immediately after activating the unit, watch the Cam Driver, fig. 6,

as it rotates around. As soon as the Cam Driver contacts the

Pinion Extension, flip the circuit breaker switch to the “RESET”

position.

Pinion

Extension

Cam

Driver

Pinion

Flat

Fig.6

Fig.7

Pinion

Extension

Cam

Driver

Pinion

Flat

Fig.11

Fig.10

Pinion

Extension

Cam

Driver

Pinion

Flat

These instructions are used to change the application of a LEO

operator from a Pull Side unit to a Push side unit.

12. The unit shown in fig.10 is configured for a pull side application.

Note the valve orientation of the closer body. The photo in fig.11

shows a close-up view of the clutch mechanism configured for pull

side application.

Instructions continued on page 3.

80-9357-0140-020 (09-10)

17. Flip the dip switch on the inverter from the Pull to the Push

position, see fig. 13.

13. Remove the four screws which secure the closer body to the

backplate.

14. Slide the closer body away from the clutch assembly and chain.

Make sure you do not remove pinion extension when removing

closer body from clutch mechanism.

15. Orient the closer body with “Latch” and “Sweep” valves toward

conduit holes, and slide onto backplate so that closer pinion is

inserted into pinion extension. Some rotational adjustment of the

pinion extension may be required to allow assembly of closer

pinion and pinion extension.

16. Replace and tighten closer body screws removed in step 12. See

fig. 12.

Fig.12

Sweep & Latch

Valves

Fig.13

Push/Pull Dip Switch

20. With door closed, slide Closed Position Magnet so it aligns with

the Reed Switch. See fig. 15.

21. Slide Open Position Magnet so it is 180° from the Reed Switch.

See fig. 16. Slide Open Position Magnet as needed to get proper

door opening.

22. Continue to page 4.

Fig.15

Closed Position

Magnet

Reed Switch

Fig.16

Open Position

Magnet

Reed Switch

Pinion

Extension

Cam

Driver

18. Verify switch is in the “ON” position for the circuit breaker and

activate unit.

19. Immediately after activating the unit, watch the Cam Driver, fig.

14, as it rotates around. As soon as the Cam Driver contacts the

Pinion Extension, flip the circuit breaker switch to the “RESET”

position.

Fig.14

Instructions continued on page 4.

80-9357-0140-020 (09-10)

Norton® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company.

Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.

3000 Highway 74 East • Monroe, NC 28112

Tel: (877)- • Fax: (800)-338-0965

www. no r to nd oo rc on tr ol s.com

974-2255

ASSA ABLOY

Inverter Adjustments:

!Based on function adjustment desired, use table above to

determine which POT is to be adjusted.

POT FUNCTIONDESCRIPTION

OBSTR SENS Obstruction Detection on Open CW - Increase

CCW - Decrease

M/DLY Motor Delay on Opening CW - Increase

CCW - Decrease

P1 Motor Reversing Speed CW - Increase

CCW - Decrease

H/O TM Hold Open Time (5 - 30 Seconds) CW - Increase

CCW - Decrease

P2 Push Recognition Sensitivity CW - Increase

CCW - Decrease

H/O TQ Motor Torque at Hold Open

Position

CW - Increase

CCW - Decrease

WARNING

120 HIGH VOLT POTENTIAL PRESENT. MAKE

SURE POWER IS TURNED OFF DURING

INSTALLATION PROCEDURE.

Dip Switch Settings

1. Door Mounting -

2. Push Recognition -

ON - pull

OFF - push

ON - active

OFF - inactive

WARNING

Electric

Shock Risk

115Y

L1 115/230VAC IN

MOTOR OUT

230Y

STATUS LEDS

PUSH PULL

SW501

H/O TQ H/O TM

OBSTR

SENS

M/DLY P2

1 6

COM

SNS

COM

JMP503

TB501

(Adjustments made in the shaded

area should be performed by

Authorized Factory Personnel.)

Inverter Details

23. Turn circuit breaker to the “ON” position.

24. Rotate Open position magnet until door opens to desired position.

Andere Handbücher für Norton LEO 5700 Series

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy DC700G-FMS-K Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 1600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600H Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Yale 3000 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6300 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 7540STH Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 1600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON 185 Quick Spotter Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT Powerglide 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton UniTrol UNI-1600BC Series Bedienungsanleitung

Assa Abloy

Assa Abloy 332 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 9500 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED8200A Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 1600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton J1600 UniTrol Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 78-B/FHA Hold Open Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5400 (A) Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung