Assa Abloy SARGENT 2900 FIREGUARD Bedienungsanleitung

NOTE:

Devices are handed and must be

the same hand as door.

RH - Right Hand Door

LHR - Left hand Reverse

LH - Left Hand Door

RHR - Right Hand Reverse

MODEL 2960

RH - Right Hand Door

LHR - Left Hand Reverse

LH - Left Hand Door

RHR - Right Hand Reverse

NOTE: Devices are handed and must be the same hand as door.

INSTALLER: LEAVE INSTRUCTIONS FOR BUILDING OWNER

Installation Instructions

1-800-810-WIRE (9473) • www.sargentlock.com A7396E 09/21

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

WARNING

This product can expose you to lead

which is known to the state of California

to cause cancer and birth defects or other

reproductive harm. For more information

go to www.P65warnings.ca.gov.

2900 FIREGUARD®

Electromechanical Closer-Holder

2980 Multipoint Hold Open with Swing Free Arm

Pull (Hinge) Side

Spindle Washer

and screw

A7396E 09/21

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2900 FIREGUARD®Electromechanical Closer-Holder

Installation Instructions

2980 Hold-Open Swing Free Arm/Pull (Hinge) Side Mounting

1 Install Body and Backplate Assembly

1. Use dimensions shown on template

provided to prepare holes.

For concealed wire applications:

Locate and drill 1-1/8" diameter

hole in the frame face for 3/4"

conduit. (This is normally done

at the time the frame is being

installed.) Connect conduit

to backplate before fastening

backplate to frame. (Figure 1)

For surface wire units:

Use conduit bracket attached to

backplate. (Figure 2)

2. Attach backplate/closer assembly to

frame. Position backplate end with

terminal strip AWAY from hinge of

frame. (Figure 1)

3. Make electrical connections as

described in Typical Wiring section.

4. Make input power connections to

power supply board as directed in

Typical Wiring section.

NOTE: If electrical connections are

to be made at a later date, place

cover on chassis now to prevent

its loss.

TOC Table of Contents

Install Body and Backplate Assembly. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Install Arm and Track .............................................................. 3

Final Adjustment and Regulating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Typical Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Template. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 1

Figure 2

3/4" Conduit

(by others)

Backplate

Closer/Holder

On/Off

Switch

Backplate

Screw (6)

Terminal

Strip

Track

Swing Free Arm

Conduit Nut

(by others)

Track Screw (2)

Closer Screw (4)

Conduit

(by others)

Conduit

Bracket

Backplate Cover

Cover Knockout

for Surface Wired Unit

A7396E 09/21

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2900 FIREGUARD®Electromechanical Closer-Holder

Installation Instructions

2980 Hold-Open Swing Free Arm/Pull (Hinge) Side Mounting

2 Install Arm and Track

Installation of the swing free arm requires

preliminary adjustment for hand of door.

1. Remove arm screws and rotate hub so that

appropriate L.H. or R.H. (hand of door)

marking aligns with arm. (Figure 3)

2. Re-install screws and spacer before

installation of arm on closer.

3. To activate swing free arm from any hold

open position, simply remove two arm

screws (and store for future use). Door

should swing freely.

4. With appropriate size wrench, rotate closer

top spindle approximately 45 degrees.

(Figure 4)

NOTE: Closing both valves for door speed

and latching speed makes this procedure

much easier.

5. Install closer arm on bottom spindle

approximately parallel to the door and arm

length AWAY from hinge.

6. Secure arm with screw and washer.

7. Remove end cap from track.

8. Position track with open side up.

9. Insert roller end of closer arm in sliding

groove of track.

10. With arm engaged in slide groove, slide

track into position so that prepared holes

on door align with track holes.

11. Replace end cap and secure track to door.

Right Hand Door

View Looking Up When

Assembling Arm to Spindle View Looking Up When

Assembling Arm to Spindle

Left Hand Door

Approximate

Preload

Position of Main Arm

When Assembled to Spindle

Index

Mark on

Spindle

Index

Mark on

Spindle

Figure 4

Figure 3

Arm

Hand of Door

Hub

Arm

Screw

3 Final Adjustment and Regulating Procedures

Adjust Spring Power According to Chart

(Figure 5)

Turn spring adjustment nut clockwise the

required number of turns to match door

width as indicated in chart.

NOTE:

• Where strong drafts exist, increase

spring power as needed.

• 351 Style door closers normally leave

the factory with spring adjustment

set at eight (8) turns.

Adjustment Instructions (Figure 6)

Minimum recommended door closing

time is 6 seconds for doors opened to

90 degrees.

Using 1/8" hex wrench, turn valve screw

clockwise to slow down or counter

clockwise to speed up door movement.

Turn backcheck valve clockwise to increase

intensity of backcheck action or counter

clockwise to decrease checking (as

desired).

CAUTION: Set backcheck valve for a slight

cushioning effect. It is damaging to the

closer if the checking action is too abrupt.

Backcheck should never be used as a

door stop. Always use a door stop to stop

the door.

Install Cover (Figure 7)

1. Assemble three (3) short cover

screws (#8-32 x 5/16") into bottom of

closer body cover mounting bracket

approximately one (1) turn.

2. Slide cover onto backplate and closer

assembly. Secure with three (3) cover

screws.

CAUTION: Avoid interference with

electronics and wires during installation

of cover.

Maximum

Width of

Door Interior

Only

Clockwise

Turns of

Adjusting

Nut

2' 8" 8

3' 0" 8

3' 6" 12

4' 0" 16

Max adjustment is approx 20

turns. Do not forcibly extend

adjustment beyond limits.

5/8" Spring

Adjustment Nut

#8-32 x 5/16"

Cover Screw

Figure 5

Figure 6

Figure 7

Hex Wrench

Backcheck

Valve

Door Closing

Speed Valve

Latching

Speed Valve

Delayed

Action

Backcheck

Latch

Sweep

A7396E 09/21

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2900 FIREGUARD®Electromechanical Closer-Holder

Installation Instructions

2980 Hold-Open Swing Free Arm/Pull (Hinge) Side Mounting

4 Typical Wiring

CAUTION

1. Disconnect all power before beginning installation to prevent electrical shock and equipment damage.

2. Installer must be a trained, experienced service person.

3. All wiring must comply with applicable local electrical codes, ordinances and regulations.

4. Maximum wire size is 18AWG.

2980 Stand-Alone Units (Figure 8)

1. Wire stand alone unit to appropriate power

supply and fire alarm.

2. Refer to data sticker for proper input voltage

and current specifications.

*WARNING: Input power supply must

match circuit board voltage rating, either

24VAC/DC or 120VAC. (Refer to data

sticker)

3. Energize power supply.

4. Open door to hold-open point. Door should

hold open.

Figure 8

5. Depress on/off switch. Door should close and

latch.

6. Adjustment of spring power may be necessary

to ensure proper latching. See Final Adjustment

and Regulating Procedures section.

7. Depress on/off switch again. Open door to hold

open position; door will hold open.

Appropriate

Power

Supply*

Earth Ground

Negative (-)

Positive (+)

Opening for

Concealed Wiring

On/Off Switch

Terminal Strip for power

input connections

*WARNING

Optional Remote

Release Connection *Data Sticker

A7396E 09/21

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2900 FIREGUARD®Electromechanical Closer-Holder

Installation Instructions

2980 Hold-Open Swing Free Arm/Pull (Hinge) Side Mounting

A7396E 09/21

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2900 FIREGUARD®Electromechanical Closer-Holder

Installation Instructions

2980 Hold-Open Swing Free Arm/Pull (Hinge) Side Mounting

5 Template

A7396E 09/21

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

1-800-727-5477 • www.sargentlock.com

2900 FIREGUARD®Electromechanical Closer-Holder

Installation Instructions

2980 Hold-Open Swing Free Arm/Pull (Hinge) Side Mounting

This page intentionally left blank.

Founded in the early 1800s, SARGENT®is a market leader in locksets, cylinders, door closers, exit devices,

electro-mechanical products and access control systems for new construction, renovation, and replacement

applications. The company’s customer base includes commercial construction, institutional, and industrial

markets.

whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited.

SARGENT Manufacturing Company

100 Sargent Drive

New Haven, CT 06511 USA

800-727-5477

www.sargentlock.com

A7396E

09/21

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy SW200 Bedienungsanleitung

Assa Abloy

Assa Abloy Lockwood L7714SDSIL Bedienungsanleitung

Assa Abloy

Assa Abloy DC140 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy Rixson Smok-Chek VI Kurzanleitung

Assa Abloy

Assa Abloy Norton 5900 Series Kurzanleitung

Assa Abloy

Assa Abloy 1370 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent Electroguard-59 80 Series Montageanleitung

Assa Abloy

Assa Abloy Norton PR1601BF Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent FIREGUARD 2408 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton UniTrol UNI-1600BC Series Bedienungsanleitung

Assa Abloy

Assa Abloy 78PRA-8L Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SW60 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin ED5600 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC3210 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 1431 Bedienungsanleitung

Assa Abloy

Assa Abloy Besam SL500 Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent PE8800 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 6000 Series Installationshandbuch

Assa Abloy

Assa Abloy Corbin Russwin PED5200 Bedienungsanleitung

Assa Abloy

Assa Abloy SECURITRON DEM680E Series Handbuch

Assa Abloy

Assa Abloy NORTON RIXSON 1600 Series Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung