Assa Abloy Sargent PE8800 Series Bedienungsanleitung

1-800-727-5477 • www.sargentlock.com

Installation Instructions

permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/patents.

WARNING

This product can expose you to

lead which is known to the state of

California to cause cancer and birth

defects or other reproductive harm.

For more information go to www.

P65warnings.ca.gov.

Attention Installer: Improper

installation may result in damage

to the product and void the factory

warranty.

WARNING

PE8800 & 12-PE8800 Series

Rim Exit Device for 16, 28, 63, & 66 Functions

A8296A 2/23

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

Screw Chart

SCREW

TOTAL QTY

SUPPLIED

WHERE USED

#10-24 X 3/4" FLAT HEAD

MACHINE SCREW

(4) CHASSIS

CORNER MOUNTING HOLES

(METAL DOOR)

#10 X 1-1/4" FLAT HEAD

WOOD SCREW

(4) CHASSIS

CORNER MOUNTING HOLES

(WOOD DOOR)

#10-24 X 3/4" ROUND HEAD

MACHINE SCREW

(2) REAR MOUNTING PLATE

(METAL DOOR)

(2) 649 STRIKE

INNER MOUNTING HOLES

#10 X 1-1/4" ROUND HEAD

WOOD SCREW

(2) REAR MOUNTING PLATE

(WOOD DOOR)

#10-24 X 3/4" OVAL HEAD

MACHINE SCREW

(2) 649 STRIKE

OUTER MOUNTING HOLES

(METAL FRAME)

#10 X 1-1/4" OVAL HEAD

WOOD SCREW

(2) 649 STRIKE

OUTER MOUNTING HOLES

(WOOD FRAME)

#8-32 X 7/16" FLAT HEAD

MACHINE SCREW

(2) CYLINDER SUPPORT

TO CHASSIS

(42 & 42T FUNCTIONS ONLY)

#8-32 X 1/4" SOCKET HEAD

SET SCREW

(1) CYLINDER SUPPORT

TO CYLINDER

(42 & 42T FUNCTIONS ONLY)

#8-32 X 5/16" W/ #6 OVAL HEAD

MACHINE SCREW

(4) CHASSIS COVER

(2) END CAP

1/4"-20 X 2-3/8" KNURLED FLAT HEAD

MACHINE SCREW

(2) EXIT TRIM

(IF USED)

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

Rail Cutting Guide (Provided)

Tools Needed

Support Block (Provided)

Before installation:

1. Install mullion, if used.

2. Fit and hang door.

3. Check the box’s label for the size of the exit device.

4. For wood doors, use wood screws and prep accordingly.

The surface of the door where the exit device is to be applied must be flush. Clear away any

raised projections to allow exit device to rest on the flat surface of the door. If shim kit is

required, contact your distributor.

Note: Please refer to trim and other installation instructions provided in the box.

DOOR HANDS DETERMINED FROM OUTSIDE OF DOOR

OR SECURED SIDE

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

Exploded View

16-Cylinder Lockdown

(Exploded View for

Clarity)

“Lock Down Key”

To operate: Depress pushrail; insert hex key,

and turn counter clockwise.

Attention:

Not available with 12- (Fire Rated) Exit

Devices.

End Cap

Mounting Plate

Rail Assembly

Rim Cylinder

649 Strike

Chassis

Chassis Cover

Mortise Cylinder

Collar

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

Door

For 649 strike Dim. “A” = 2-1/4”

For 613 strike Dim. “A” = 1-3/4”

For 642 strike Dim. “A” = 1-1/2”

Vertical reference

line (℄of chassis)

“A”

Single Door (Non-Fire Rated)

DoorDoor

649 Strike

2-1/4”

Vertical reference

line (℄of chassis)

Double Door with 980 Mullion

Door

649 Strike

2-1/4”

Vertical reference

line (℄of chassis)

Single Door (12 - Fire Rated Exit Device)

DoorDoor

649 Strike

2-1/4”

Vertical reference

line (℄of chassis)

Double Door with 12-980 Mullion

Measure and mark chassis vertical centerline, rail

horizontal centerline, and horizontal reference line

(bottom chassis mounting holes).

Prepare Door

36-1/4" 39-5/8"

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

Extend rail horizontal centerline

Align chassis template with reference lines. Tape

to door surface. Mark all holes and openings.

Drill and tap (4) #10-24 chassis mounting holes,

and cut out opening for chassis bell housing /

thumbpiece clearance (this side only).

Align trim template to outside of door. Tape to

door surface. Mark all holes and openings.

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

Drill thru-holes for trim mounting screws. Cut out

openings for lever spindle and cylinder, if used

(this side only)

8 9

Drill and tap (2) #10-24 tapped holes.

Extend rail horizontal centerline to frame.

Align strike on centerline, flush against door face,

and mark location of outer screw holes.

Install Strike

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

10 11

Attach chassis with (4) #10-24 flat head machine

screws. DO NOT FULLY TIGHTEN.

Attach strike with (2) #10-24 oval head ma-

chine screws and lock washers.

Install Chassis

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

If the rail doesn’t need to be cut, continue to page 10, step 12.

If the rail must be cut, follow these steps on page 8 and 9:

Refer to the individual exit device installation instructions for rail cutting requirements / restrictions.

Instructions will vary based on device type and options.

Do not cut closer than 1-5/8" from

the the front edge of the rail insert.

• Determine cut off dimension “X” by subtracting 2-7/8"

from dimension “Y”. Mark cut off point on mounting

rail. (See below.)

Vertical reference line (C of chassis)

2-7/8"

min.

For doors with stile rail, the stile must overlap by 5/16"min.

A. Ensure there isn’t a gap between the insert

and the dogging slope, and the carrier is

flush with the mount.

DOGGING

SLOPE

INSERT

B. Mark rail at the required cut length.

Insert

Dogging

slope

Cut line

Mount

Carrier

Information for Cutting Rails

Rail Sizes Door Widths

MinimumStandard

E 32" 24"

F 36" 33"

J 42" 37"

G 48" 43"

Rail cutting guide

1-800-727-5477 • www.sargentlock.com

the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent

www.assaabloydss.com/patents.

A8296A 2/23

PE8800 & 12-PE8800 Series

Installation Instructions

Rim Exit Device for 16, 28, 63, & 66 Functions

CUT LINE

F. Using a hack saw with a new blade or a chop

saw with a metal cutting blade, cut the rail,

ensuring that the blade stays pressed against

the rail cutting guide.

G. Deburr and smooth all cut edges with a file.

D. Wrap the rail and insert in masking tape, as

shown.

E. Place the rail cutting guide over the masking tape and align it with the cut line. Clamp the cut guide to the rail

using a C-clamp.

C. Ensure plastic insert support is installed under the

cut line.

Cut line

Rail Cutting Guide

Rail cutting guide, continued.

Andere Handbücher für Sargent PE8800 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Assa Abloy Türöffnungssystem Handbücher

Assa Abloy

Assa Abloy Corbin Russwin ED7400 Series Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 6200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON W91DCP Bedienungsanleitung

Assa Abloy

Assa Abloy Norton SafeZone 7100SZ Series Kurzanleitung

Assa Abloy

Assa Abloy SW60 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 351 Bedienungsanleitung

Assa Abloy

Assa Abloy Sargent 2409 Series Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 2900 FIREGUARD Bedienungsanleitung

Assa Abloy

Assa Abloy SW100 Bedienungsanleitung

Assa Abloy

Assa Abloy 5800 ADAEZ PRO Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED5000 DB Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC700G-FT Bedienungsanleitung

Assa Abloy

Assa Abloy RIXSON SMOK-CHEK V 0101 Bedienungsanleitung

Assa Abloy

Assa Abloy NORTON RIXSON 5200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy G-S Bedienungsanleitung

Assa Abloy

Assa Abloy SW200 Handbuch

Assa Abloy

Assa Abloy Besam SW300 Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Securitron EEB3N Bedienungsanleitung

Assa Abloy

Assa Abloy SARGENT 281 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Corbin Russwin PED4200 Series Bedienungsanleitung

Assa Abloy

Assa Abloy Norton 5900 Series Kurzanleitung

Assa Abloy

Assa Abloy Norton 6011 Series Bedienungsanleitung

Assa Abloy

Assa Abloy DC200 Bedienungsanleitung

Beliebte Türöffnungssystem Handbücher anderer Marken

Pamex

Pamex KT-INP35 Bedienungsanleitung

Cal-Royal

Cal-Royal N-F77CVR Bedienungsanleitung

Scrigno

Scrigno OPEN1000 Bedienungsanleitung

TriMark

TriMark UM 34 Bedienungsanleitung

BFT

BFT WIND RMB 130B 200 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Besam

Besam Swingmaster MP Leitfaden

CRL

CRL SENIOR PRIMA Bedienungsanleitung

GAL

GAL MOVFR Technisches Datenblatt

Normstahl

Normstahl IDO7 Bedienungsanleitung

Häfele

Häfele Finetta T 70 VF Bedienungsanleitung

AGS

AGS D-PL Handbuch

Stanley

Stanley MA900ñ Montageanleitung

WITTUR

WITTUR Hydra Plus UD300 Handbuch

Alutech

Alutech TR-3019-230E-ICU Montage- und Bedienungsanleitung

MPC

MPC ATD ACTUATOR 50 ATD-313186 Operating and Technisches Datenblatt

GEZE

GEZE ECturn Bedienungsanleitung

Chamberlain

Chamberlain T Bedienungsanleitung