Bristan DSC 3HBAS C Montageanleitung

Please keep this booklet for future

reference.

Installer, when you have read these

instructions please ensure you leave

them with the user.

Models Covered:

DSC 3HBAS C, DSC 3HBF C,

DSC WMBAS C, DSC WMBF C, DSC

BS C

Installation Instructions

and User Guide

Descent Tap Range

Contents

• Important Safety Information 3

• General Information 4

• Speciﬁcations 4

• Dimensions (mm) 5 - 7

• Installation Requirements 8

• Installation 9 - 11

• Maintenance 12

• Troubleshooting 13

• Guarantee 14

• Notes 15

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Contents

Thank you for choosing Bristan.

These ﬁtting instructions have been created to give you all of the information you

need for a safe and successful installation, so please read them thoroughly and

retain for future reference.

If you need any further help, please do not hesitate to give us a call on 0330 026 6273.

• Before starting any installation

please consider the following: before

drilling into walls, check that there are

no hidden electrical wires, cables or

water supply pipes. This can be checked

with the aid of an electronic detector.

• If power tools are used do not

forget to:

- Wear eye protection

- Unplug equipment after use

• Fitting isolating valves to the

inlet feeds is required for ease of

maintenance.

• Warning: Before installing

the new spout it is essential

that you thoroughly

ﬂush through the pipework

in order to remove any remaining swarf,

solder, etc. Failure to carry out this

procedure could cause problems or

damage to the workings of the spout.

• This product must not be modiﬁed

in any way as this will invalidate the

guarantee.

• Please read these instructions

thoroughly and retain for future use.

• All products manufactured and

supplied by Bristan are safe provided

they are installed, used correctly

and receive regular maintenance in

accordance with these instructions.

• If you are in any doubt about

your ability to install this product

safely you must employ the

services of an experienced qualiﬁed

plumber/electrically qualiﬁed

person.

• Warning: Do not

operate the product

if you suspect it is

frozen. Do not site the

product where it might be subjected

to freezing conditions.

• These ﬁttings need to be

installed in accordance with, and

meet the requirements of the Water

Supply (Water Fittings) Regulations

1999

and current byelaws.

• Remove all packaging and check

the contents for damage before

starting installation

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Important Safety Information

This product has been designed to comply with BS EN 200 for combination

taps to be used within systems designed to BS 6700.

BS 6700 recommends the temperature of stored water should never exceed

65°C. A stored water temperature of 60°C is considered sucient to meet all

normal requirements and will minimise the build up of lime scale in hard water

areas.

If installing this product on a low pressure (tank fed) system please see

speciﬁcation table below to determine the minimum distance required from

underside of the cold water tank to the outlet.

These taps and mixers should be installed in compliance with the Water

Regulations. Where the supplies are unbalanced, i.e. Hot water from cylinder

tank/cold from the mains, approved check valves must be ﬁtted in the supply

pipes.

For further details contact your Local Water Authority.

P r o d u c t

Code

Working

Pressures Inlet

Minimum distance

from cold water

tank to outlet

(metres)

Min Max

DSC 3HBAS C 0.2 5.0 15mm Compression

Threaded Tail

DSC 3HBF C 0.4 5.0 3/4" BSP Threaded Tail 4

DSC WMBAS

0.2 5.0 15mm Compression

Threaded Tail

DSC WMBF C 0.5 5.0 22mm Compression

Threaded Tail

DSC BS C 0.2 5.0 1/2" BSP Threaded Tail 2

Maximum static pressure: 10.0 bar

System Requirements:

Gravity fed hot & cold (Equal pressures)

Gravity fed hot & cold (Dierential pressure, maximum ratio 5:1)

Unvented systems

Instantaneous water heater (Combination boiler)

Speciﬁcations

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

General Information

Dimensions are approximate and in millimetres.

110

140

115

G1 1/4”

110

1/2" BSP

107

3 Hole Basin Mixer

3 Hole Bath Filler

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 5

Dimensions

Wall Mounted Basin Mixer

Dimensions are approximate and in millimetres.

Bath Spout

182

270

70 50

45 215

200

220

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Dimensions Cont.

Dimensions are approximate and in millimetres.

Wall Mounted Bath Filler

270

100

115

200

60 190

185

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 7

Dimensions Cont.

Flexible Connecting Pipes

Care must be taken when connecting the ﬂexible connection pipes to the household

pipework to ensure they do not bend sharply and kink or twist.

See below for recommended ways to ﬁt the ﬂexible connecting pipes.

Important: Failure to follow these guidelines may result in poor performance

and damage to the ﬂexible connecting pipes.

Important: Full access must be made available on installation for future

maintenance/ servicing purposes.

Slight

bend

90 °

angle

Kinks

Curved

round Twists

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Requirements

1. With the backnut, metal and rubber

washer ﬁtted to the side body threaded

tail, put the side body through the hole in

the basin / bath from underneath.

2. Screw the shroud, ensuring the washer

is ﬁtted between the shroud and basin /

bath, onto the threaded tail and tighten

backnut underneath onto the bottom of

the basin/bath. The screws on the

backnut allow for any uneven surfaces

and should be tightened up to metal

washer. Replace the handle, grub screw

and the cap.

3. Fit the spout to the basin/bath

tightening the backnut. The screws on

the backnut allow for any uneven

surfaces and should be tightened up to

metal washer.

4. Attach the T- joint assembly and

connect to the side bodies (hot on the

left, cold on the right when viewed from

the front), by using the ﬂexi tails supplied.

5. Connect the hot and cold water

supplies to the side bodies (hot to the left,

cold on the right hand side), fully open

both valves, letting the water ﬂow for a

few minutes to ﬂush the system.

6. Fit the clicker waste (basin mixer only)

ensuring the rubber washer is ﬁtted

between the basin and the waste. Place

the other rubber washer under the basin

and secure in place by tightening the

backnut. In order to ﬁll the basin, the

button in the middle of the waste needs

to be pressed down. To release the water,

press the button again.

7. Check all joints and connections

for leaks.

3 Hole Basin Mixer/ Bath Filler

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors. 9

Installation

Wall Mounted Basin Mixer and

Bath Filler

1. Decide on the ﬁnal position of the basin

mixer/bath ﬁller. Install suitable batons into

the wall cavity if required to support the

tap body.

2. Plumb the hot and cold water supply

pipes to the required position.

3. Secure mixer body using the screws and

wall plugs supplied.

4. Attach the supply pipework to the hot

and cold inlets (hot on the left and cold on

the right when viewed from the front) en-

suring the olive is ﬁtted to the copper pipe

work. Tighten the compression nut to secure

the pipework and create a water tight seal.

Note: Before ﬁnishing the wall surface turn

on both water supplies to check for any

leaking connections.

5. Finish the wall surface.

Note, it is important that a sucient amount

of the spout connecting tube and valves are

left exposed to allow the spout and valve

shrouds to ﬁt.

6. Fit the spout and tighten the grub screws

to secure in position.

7. Screw the valve shrouds onto the valves

using the screws supplied. Push the plinth

over the shroud.

8. Fit the spline adaptors to the valve splines

using the screws and washers supplied.

9. Push the handles onto the valve shrouds

and tighten the grub screws.

10. Turn on both water supplies and operate

the handle letting the water ﬂow for a few

minutes to ﬂush the system.

Need help? Give us a call on 0330 026 6273 and speak to one of our trained advisors.

Installation Cont.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Bristan Sanitärprodukte Handbücher

Bristan

Bristan Java J BF C Bedienungsanleitung

Bristan

Bristan JU BAS C Bedienungsanleitung

Bristan

Bristan W BASIN12 C Verdrahtungsschema

Bristan

Bristan DSC SHC3DIV C Verdrahtungsschema

Bristan

Bristan smile Montageanleitung

Bristan

Bristan CR SHXDIVFF C Verdrahtungsschema

Bristan

Bristan GLL RAPSNK4 C Montageanleitung

Bristan

Bristan BUZ2 SHXDIVCTFF C (D4) Verdrahtungsschema

Bristan

Bristan EXD BAS C Bedienungsanleitung

Bristan

Bristan RO2 SHXAR C Montageanleitung

Bristan

Bristan K SNKSL EF C Bedienungsanleitung

Bristan

Bristan DSC 3HBF C Bedienungsanleitung

Bristan

Bristan Quadrato Tap Range Verdrahtungsschema

Bristan

Bristan W BASIN15 C Bedienungsanleitung

Bristan

Bristan Body Jet JET2 C Bedienungsanleitung

Bristan

Bristan EV KIT-EFB C Montageanleitung

Bristan

Bristan Java Eco Click J EBAS C Bedienungsanleitung

Bristan

Bristan Target TG SNK C Bedienungsanleitung

Bristan

Bristan Quest Deck Sink Mixer Verdrahtungsschema

Bristan

Bristan CRAZE CRZ2 SHXDIVCTFF C Verdrahtungsschema

Bristan

Bristan Blade BL BAS C Bedienungsanleitung

Bristan

Bristan FIXED HEADS FHC ABRD01 C Bedienungsanleitung

Bristan

Bristan Descent Series Bedienungsanleitung

Bristan

Bristan GLR 1/2 C Bedienungsanleitung

Beliebte Sanitärprodukte Handbücher anderer Marken

Weka

Weka 506.2020.00E Betriebsanleitung

American Standard

American Standard DetectLink 6072121 Bedienungsanleitung

Kohler

Kohler K-6228 Montageanleitung

Uponor

Uponor Contec TS Bedienungsanleitung

Pfister

Pfister Selia 49-SL Bedienungsanleitung

Fortis

Fortis VITRINA 6068700 Bedienungsanleitung

Kohler

Kohler K-12183 Montageanleitung

Maxxus

Maxxus MX-M206-01 Bedienungsanleitung

Viega

Viega Prevista Pure 8512 Bedienungsanleitung

Kohler

Kohler Centerset K-15240 Montageanleitung

Viega

Viega Prevista Dry 8522.33 Bedienungsanleitung

Sanela

Sanela Lema SLP 59RB Bedienungsanleitung

Elkay

Elkay EDF15AC Installationshandbuch

Hans Grohe

Hans Grohe AXOR Citterio E 36702000 Handbuch

baliv

baliv WT-140 Bedienungsanleitung

Kohler

Kohler Mira Eco Bedienungsanleitung

BELLOSTA

BELLOSTA romina 0308/CC Bedienungsanleitung

Crosswater

Crosswater Heir 18-31 Bedienungsanleitung