Clarke CSP1530 Bedienungsanleitung

OPERATION & MAINTENANCE

INSTRUCTIONS

GC08/22

ORIGINAL INSTRUCTIONS

1530W SEWAGE PUMP

MODEL NO: CSP1530

PART NO: 7230293

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

INTRODUCTION

Thank you for purchasing this CLARKE submersible pump.

The CLARKE range of submersible pumps are suitable for discharging pools,

ponds, fountains, pits and any waste water drainage. They can handle foul

water containing suspended material as stated in the specification. The

pumps are not suitable for handling inflammable, corrosive, explosive or

dangerous liquids. The pump is water-cooled and does not contain any oil.

The ‘Pump Performance Curve’ graph shown, displays the characteristics

graphically and describes the relation between the flow-rate and the head

for the pump.

The pump is provided with a thermal overload cut-out, so that in the event

that the pump becomes overheated (due to becoming blocked etc) it will

shut off automatically. When the blockage has been cleared, the thermal

cutout will cool down and re-set and the pump can be re-started.

Before attempting to use this product, it is essential that you read this manual

thoroughly and carefully follow all instructions given. In doing so you will ensure

the safety of yourself and that of others around you, and you can also look

forward to the product giving you long and satisfactory service.

SPECIFICATIONS

Voltage 230V~50Hz

Ingress Protection IP68

Outlet Diameter 2”(50mm)

Rated Output Power 1530 W

Maximum Head Height 10 m

Maximum Depth 8 m

Maximum Output 500 l/min

Maximum Operating Temperature 40oC

Maximum Solid body Size in Suspension 35 mm

Weight 19 kg

Cable Length 10 m

Dimensions (D x W x H) 270 x 170 x 460 mm

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

OVERVIEW & FEATURES

1. Water inlet screen

2. Power cable with plug

3. Water outlet

4. Lifting handle

PUMP PERFORMANCE

CHART

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

SAFETY PRECAUTIONS

WORK AREA

1. Keep the work area clean and well lit. Floors should always be kept clear.

Cluttered or dark areas invite accidents.

2. Keep children and bystanders away while operating the pump.

Distractions can cause loss of control.

3. Remember, the operator or user is responsible for accidents or hazards

occurring to other people or their property.

PERSONAL SAFETY

1. ALWAYS stay alert, watch what you are doing and use common sense

when operating this pump. Do not install the pump while you are tired or

under the influence of medication, drugs or alcohol. A moment of

inattention can result in personal injury.

2. DO NOT over-reach. Keep your proper footing and balance at all times

when positioning the pump.

3. NEVER direct the water discharge towards electrical wiring or equipment.

4. ALWAYS store the pump out of reach of children and do not allow persons

unfamiliar with these instructions to operate it.

5. NEVER direct the discharge flow towards another person.

6. ALWAYS thoroughly familiarise yourself with this pump & its operation and

follow all instructions in this manual.

7. ALWAYS ensure that the pump is properly positioned where necessary to

prevent it from moving during operation, and that the immediate area

surrounding the pump is kept clear.

GENERAL USE AND CARE OF THE PUMP

1. An approved Residual Current Device (RCD) must be used when pumping

from ponds or swimming pools.

2. ALWAYS lift the pump using the handle and use a rope or chain attached if

necessary to lower it into the water. Never lift or carry the pump by the

power cable.

3. NEVER use this pump if any part is damaged. Have it inspected and

repaired by your local CLARKE dealer.

4. ALWAYS use an approved cable extension suitable for the power rating of

the pump (see specifications). The conductor size should also be at least

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

the same size as that on the pump, or larger. When using a cable reel,

always unwind the cable completely.

5. ALWAYS maintain the pump with care and keep it clean.

6. NEVER use for pumping flammable liquids or corrosive chemicals. These

pumps are designed to pump water only.

7. NEVER abuse the electrical cable. Never use the cable for pulling or

unplugging the pump. Damaged or tangled cables increase the risk of

electric shock.

8. NEVER run the pump dry. Always ensure the pump is immersed in water

before starting. Switch the pump OFF immediately the task is completed

9. NEVER pump water from a swimming pool when there is a person or animal

still in the pool.

10. NEVER install the pump on sand, silt or mud which is likely to shift or

collapse.

11. NEVER modify this pump in any way. Use it only for the purpose for which it

is designed.

SERVICING & REPAIRS

1. ALWAYS have the pump serviced by your local CLARKE dealer, using only

identical replacement parts. This will ensure the safety of the pump is

maintained. The use of non standard parts could be hazardous.

2. NEVER attempt any repairs yourself unless technically qualified. If you have

a problem with the pump contact your local CLARKE dealer.

3. ALWAYS disconnect the pump from the electrical supply before placing it

into, or removing from the water, and before any cleaning or

maintenance.

4. If the power cable becomes damaged, it must be replaced rather than

repaired.

5. Your CLARKE water pump has been designed to give long and trouble free

service. If, however, having followed the instructions in this booklet

carefully, you encounter problems, take the unit to your local CLARKE

dealer.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ENVIRONMENTAL RECYCLING POLICY

Through purchase of this product, the customer is taking on the

obligation to deal with the WEEE in accordance with the WEEE

regulations in relation to the treatment, recycling & recovery and

environmentally sound disposal of the WEEE.

In effect, this means that this product must not be disposed of with general

household waste. It must be disposed of according to the laws governing

Waste Electrical and Electronic Equipment (WEEE) at a recognized disposal

facility.

This product contains valuable raw materials. Metal products should be

takento your local civic amenity site for recycling of metal products. Recycle

unwanted materials instead of disposing of them as waste. All unwanted

accessories and packaging should be sorted and taken to a recycling centre

for disposal in a manner which is compatible with the environment.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

ELECTRICAL CONNECTIONS

Connect the mains lead to a standard, 230 Volt (50Hz) electrical supply

through an approved 13 amp BS 1363 plug, or a suitably fused isolator switch.

If the plug has to be changed because it is not suitable for your socket, or

because of damage, it must be removed and a replacement fitted, following

the wiring instructions shown below. The old plug must be discarded safely, as

insertion into a power socket could cause an electrical hazard.

If the colours of the wires in the power cable do not agree with the markings

on the plug proceed as follows

• The BLUE wire must be

connected to the

terminal marked N or

coloured black.

• The BROWN wire must

be connected to the

terminal marked L or

coloured red.

• The YELLOW AND

GREEN wire must be

connected to the

terminal marked E or

or coloured green.

AN APPROVED RESIDUAL CURRENT DEVICE (RCD) WHICH HAS A TRIPPING

CURRENT OF LESS THAN 30MA MUST BE USED.

If you are not sure, consult a qualified electrician. DO NOT try to do any

repairs.

WARNING: READ THESE ELECTRICAL SAFETY INSTRUCTIONS

THOROUGHLY BEFORE CONNECTING THE PRODUCT TO THE MAINS

SUPPLY.

Plug must be BS1363/A approved.

Always fit

Ensure that the outer sheath of

Neutral

(Blue)

Live

(Brown)

Earth

(Green and

a 13 Amp

the cable is firmly held by the clamp

fuse.

Yellow)

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

POSITIONING AND CONNECTION

Remove all packaging and make sure that the unit contains no visible

damage. Dispose of all packaging appropriately.

CONNECTING THE PUMP

1. Connect the outlet adaptor to the largest diameter hose available, as any

restriction will reduce capacity and put unnecessary strain on the motor if

a long run of discharge hose is being used.

• The adaptor fitting allows for connection of 51 mm (2”) hoses which

should be secured with a hose clamp.

• Suitable hoses are available from your local CLARKE dealer.

POSITIONING THE PUMP

1. It may be safer to raise and lower the pump into deep water using a rope

attached to the lifting handle.

2. Place the pump in a vertical position resting on a firm, flat surface in the

area that you want to drain. If there is sediment in the operating area, the

pump should be placed vertically on house bricks, or similar but ensure

they are not likely to collapse. Never position the pump on sand, silt, mud

or ground which is likely to collapse.

3. Keep the pump clear of sediment by standing it on a platform or brick or

suspending from a rope attached to the handle if the pump is to be used

where there may be silt or mud etc (e.g. garden ponds).

4. Route the hose as straight as possible. Excessive bending of the hose could

obstruct the flow of water, reduce the pumping volume or clog the pump

with mud, thus disabling the pumps function. If the hose is kinked at its base

it will create air pockets in the pump, causing it to operate in a partially dry

state. Take care to straighten any kinks or bends in the hose.

5. Do not operate the pump if the water is too shallow. This will be below the

level of the outlet elbow with the impeller fully immersed.

6. Allowance must also be made for the overall width of the pump including

the outlet elbow on one side.

• When the pump is being used in a permanent or semi-permanent

installation, a non-return valve should be fitted in the delivery hose.

Suitable hoses and valves are available from your CLARKE dealer.

• Take all necessary precautions as described on pages 4-5.

• The pump inlet must be fully submerged before being switched on.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

USING THE PUMP

1. Plug in the pump and switch on the power supply.

• Suitable hoses are available from your local CLARKE dealer.

2. Run the pump continuously or remove from the water and store in a frost

free location if the water is likely to freeze.

3. NEVER run the pump dry. Ensure the pump is switched off when water has

stopped flowing.

• The pump should be able to clear water down to a residual depth of the

inlet port, In this situation, air and residual water may be seen escaping

from the discharge hose.

4. Disconnect from the power supply when the water has been pumped out.

Avoid running the pump continuously if the discharge hose has become

obstructed and water is not flowing.

5. Disconnect the pump from the mains supply before placing it into or

removing it from the water.

6. NEVER carry the pump by the power cable. Always use the handle or a

rope tied securely to the handle.

7. NEVER insert your fingers into the pump whilst it is connected to the mains.

8. DO NOT use the pump if the water is liable to freeze, as this can cause

damage to the pump. Remove the pump from the water and store it in a

frost free location.

OVERLOAD PROTECTION

These pumps are fitted with automatic thermal overload protection.

If the pump overheats due to an obstruction in the pump, or pumping warm

water for example, it will shut off automatically.

Switch the pump OFF at the mains supply. Check for blockages and allow the

motor to cool (at least 5 minutes) by which time the cut-out will have reset.

Once the pump has cooled the pump will automatically restart.

WARNING: CHECK THE PUMP FOR DAMAGE BEFORE USE, DO NOT USE THE

PUMP IF IT IS DAMAGED IN ANY WAY.

Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com

CLEANING, MAINTENANCE & STORAGE

The pump should require no maintenance other than regular inspection and

cleaning.

1. Inspect the pump prior to use and DO NOT use the pump if there is any

damage to the mains power cable.

2. Check pump regularly to ensure the inlet is clear of leaves or other debris. It

can be cleaned out either by back-flushing and cleaning out by hand.

3. If the pump has been used for pumping swimming pool water or salty

water likely to leave chemical residues, it should be flushed through with

clean water before storage.

4. When the pump is not being used for extended periods, clean and dry it

thoroughly and store in indoors. if the pump is left in water, it should be run

at least once a week to prevent it from seizing up.

5. If the pump shows signs of wear or damage, contact your CLARKE dealer

for advice. DO NOT attempt to repair the pump yourself, as you may

damage the waterproof seals and invalidate your guarantee. Repairs

should be carried out by your local CLARKE dealer, or contact the CLARKE

Service Department on 020 8988 7400.

WARNING: MAKE SURE THAT THE PUMP IS DISCONNECTED FROM THE

POWER SUPPLY BEFORE CLEANING OR PERFORMING MAINTENANCE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Clarke Wasserpumpe Handbücher

Clarke

Clarke HSE Series Installations- und Betriebshandbuch

Clarke

Clarke CFTP12 Bedienungsanleitung

Clarke

Clarke CS85S Installations- und Betriebshandbuch

Clarke

Clarke IVP13A Installations- und Betriebshandbuch

Clarke

Clarke SPE800 Bedienungsanleitung

Clarke

Clarke psp125b Bedienungsanleitung

Clarke

Clarke MSP12 Bedienungsanleitung

Clarke

Clarke ISP11A Handbuch

Clarke

Clarke CVPW Kurzanleitung

Clarke

Clarke PSV3A Installations- und Betriebshandbuch

Clarke

Clarke CWBP300 Bedienungsanleitung

Clarke

Clarke CPE20A3 Bedienungsanleitung

Clarke

Clarke ECP20A3 Bedienungsanleitung

Clarke

Clarke PW2 Bedienungsanleitung

Clarke

Clarke CPPRSS Bedienungsanleitung

Clarke

Clarke CBM250SS Bedienungsanleitung

Clarke

Clarke LVP1A Bedienungsanleitung

Clarke

Clarke PF75 Bedienungsanleitung

Clarke

Clarke SPE800 Installations- und Betriebshandbuch

Clarke

Clarke CWP200 Bedienungsanleitung

Clarke

Clarke CBP900 Bedienungsanleitung

Clarke

Clarke HIPPO 2 Bedienungsanleitung

Clarke

Clarke ISP14A Installations- und Betriebshandbuch

Clarke

Clarke CHF2 Installations- und Betriebshandbuch

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung