CrimeStopper CS-2011RS.III Bedienungsanleitung

CS-2011RS Series III

Super Rage™

Remote Control Alarm & Remote Engine Starting System

OPERATION INSTRUCTIONS

INTRODUCTION

CONGRATULATIONS on your choice of a Super Rage™ Alarm & Remote Engine Starter by Crimestopper Security

Products Inc. This booklet contains the information necessary for operating your system. If any questions arise,

contact your installation dealer or Crimestopper Security Products Inc.

*IMPORTANT INFORMATION: Primary and Optional Features

-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Power,

Ground, Lights, Power Locks, etc.

-OPTIONAL: Optional features are connected only if desired or agreed upon by the installing dealer i.e. Horn Honk,

Dome light illumination, Starter Kill, L.E.D., Trunk Pop, etc. These features may require additional parts and labor

charges. Consult with your installer about these features before installation.

CONTACT INFORMATION:

TECHNICAL SUPPORT (800)-998-6880

Monday -Friday 8:00am -4:30pm Pacific

Website: www.crimestopper.com

E-mail: tech-[email protected]

CRIMESTOPPER

SECURITY PRODUCTS, INC.

1770 S. TAPO STREET

SIMI VALLEY, CA. 93063 REV. A8.2002 S/W: 620

This device

complies with FCC Rules part 15. Operation is subject

to the following two conditions: 1) This device may not cause

interference, and (2) this device must accept any interference that

may be received, including interference that may cause undesired

operat

ion. The manufacturer is not responsible for any radio or TV

interference caused by unauthorized modification to this

equipment. Such modification could void the user's authority to

operate the equipment.

TABLE OF CONTENTS

Operation Cautions & Warnings……..…………..……………………………………………………………………2

Operating Instructions-Alarm……………………………………………………….………..……………..……..3-5

LED Diagnostics………………..……………………………………………………………………….………..…..….6

Remote Engine Control………………………...…………………………………………………….………...…….6-9

Anti-Carjack Protection...……………………………………….………….……..…………...…………..…….…9-10

Transmitter Programming……………………………….……………………………………………..…………10-11

2 Vehicle Operation……...………………………….……………………………….………….…………….….……11

Troubleshooting: “Before you call section”………………………………………………………………...…….12

OPERATION CAUTIONS & WARNINGS

CRIMESTOPPER SECURITY PRODUCTS, INC. and its VENDORS shall not be liable for any accident

resulting from the use of this equipment. This system is designed to be professionally installed into a car or

vehicle in good running order. Items, such as parking brake, door switches, and all engine safety features,

must be in perfect working condition.

DAMAGE resulting from misuse or negligence is NOT covered under warranty and will be subject to

repair and / or replacement charges.

IT IS ABSOLUTELY THE OWNER’S SOLE RESPONSIBILITY TO: A) Understand the operation of this

system and its safety features. B) Check for proper operation of these safety features prior to accepting

deliveryofthevehiclefromtheinstallationfacility. C)Checkandmaintaintheconditionof the vehicle and all

items relative to the proper operation of this system and its safety features.

DO NOT remote start the vehicle in a closed garage. Makesurethatthevehicleisoutdoors,agaragedoor

is open, or there is adequate exhaust ventilation. Failure to observe this rule could result ininjury or death

frompoisonous CarbonMonoxide fumes. Thisis especiallyimportant whenusing theTimedSelf-Start feature

of the unit

CS-2011RS TRANSMITTER BUTTONS

START

ARM/

TRUNK REMOTE

START

UNLOCK

CAR 1-2

LOCK

DISARM

OPERATING INSTRUCTIONS -ALARM

Active Arming / Locking:

Press button #1 (Lock symbol) on the transmitter. The System will

arm and confirm with one siren chirp, one light flash, and the LED

will begin to flash. Power locks will lock (if equipped). Starter

disable circuit will turn on. After a short delay to allow the vehicle

and electronics to settle, the system will be completely armed.

Disarming: / Unlocking

Press button #2 (Unlock symbol) on the transmitter. System will

disarm and confirm with two siren chirps, two light flashes, and the

LED will turn off. Power locks will Unlock and Interior Dome light will

turn on (if installed with these optional features)

Disarming While Tripped (Triggered):

Disarming the System while it is triggering requires TWO presses of the #2 Unlock Button. The first press of

Button #2 Resets the alarm cycle only (system still armed) while a second press will disarm/unlock the system.

Silent Arming/Disarming:

To Arm or Disarm the system without siren chirps, press and release both Buttons #2 (Unlock) and #4 (Start)

at the same time. System will Arm or Disarm without siren chirps. Flashing lights and LED will be the only

indicators of Arm/Disarm status. If the system was tripped while you were way, 4 chirps will be heard to notify

you that the system was tripped.

Alarm Triggering

An intrusion into the vehicle or hard impact to the body will sound the alarm and flash the lights for 1 minute.

After 1 minute the trigger cycle will automatically stop and alarm will remain armed to continue protecting the

vehicle. If a door is left open after an intrusion then the unit will cycle a maximum of 5 minutes and continue to

protect the other un-tampered or unopened zones.

Prior intrusion Alert

This system will notify you if the alarm was tripped while you where away. Upon disarming, the two normal

disarm chirps will be heard then the system will emit 4 additional siren chirps. Check your vehicle for any

signs of a break in or tampering. Also see LED Diagnostics Section to determine the cause of the trigger.

Remote Panic Protection

To sound the alarm in an emergency situation or to draw attention to your vehicle, press and hold Button #1

(Lock) for at least 3 seconds until the siren sounds. Press Button #2 (Unlock) to reset panic mode.

OPERATING INSTRUCTIONS -ALARM

Arming With Shock Sensor Bypass

To arm the alarm and bypass shock sensor protection, press Button #1 as normal then press and release

Button #1 and #2 together within 2 seconds. You will hear 3 extra siren chirpsindicating shock sensor bypass

for this arming cycle only.

Open Door Alert / Bypass

Upon arming, this system will warn you if a door is left open. After a 60 second setup delay (for extended

dome lights) has elapsed, if the system detects a fault or a door left open, the siren will chirp 5 times along

with 5 light flashes. This zone will be automatically bypassed and the alarm will continue to protect all other

zones.

Pre-Warning Shock Protection

The Pre-warning (warn-away) feature will activate when a low-level shock or vibration detected by the

system’s shock sensor. The alarm will chirp the siren 5 times and flash the lights once to help deter any

further tampering with the vehicle.

Passive Arming Mode: (Programmable)

Passive (automatic) arming occurs 30 seconds after the ignition is turned off and the last door is closed. Upon

closing the last door, the unit will flash the lights twice and LED will be flashing rapidly to confirm passive

countdown. If a door is reopened within the 30 second period, the countdown stop and begin again when the

door is closed. Passive arming provides failsafe protection in case you forget to arm the system.

Passive Locking: (Programmable)

The CS2011RS system can be programmed to passively lock the doors when the system passively arms.

The default setting is OFF because passive locking increases the risk of locking the keys in the vehicle.

Trunk/Hatch Pop (Optional, Remote AUX. Output 1)

This feature is designed to interface with existing Factory power trunk or power hatch release systems and

may require additional parts and/or labor charges. Press and release Button #3 (Trunk) on the transmitter to

pop/open the trunk/hatch. If the system is armed, it will also disarm when the button #3 is pressed.

Remote AUX. Output 2 (Optional)

This system contains a second auxiliary output to activate other accessories or devices. To activate the

systems’ Second Auxiliary Output, press and hold Button #3 (Trunk Symbol) on the transmitter for more than 2

seconds. This is a momentary output that will stay active as long as the remote button is held down.

OPERATING INSTRUCTIONS -ALARM

Dome Light Illumination (Optional)

This feature will turn on the vehicle’s dome light upon disarming for 30 seconds or until the key is inserted and

turned on. This will provide illuminated entry to your vehicle in dimly lit areas for safety and security.

Emergency Override (Disarm)

If you have lost the transmitter or it stops working for any reason and the Alarm is armed, you will have to

disarm the system manually. Open the door with the key [alarm will sound], turn the ignition on, and press the

override/program button for about 5 seconds. The Alarm will disarm and allow you to use the vehicle until you

can repair/replace the remote. Note that you may need to put the system into valet mode to prevent passive

arming.

Valet Mode (Enter manually or using the remote)

To disable Alarm and Remote Engine Starting for vehicle servicing or otherwise, turn the ignition on and press

the override/program button [about 5-7 seconds] until you hear (3) siren chirps and the LED turns on solid.

Repeat the process to exit VALET mode. To enter / exit valet via the remote, press and hold both buttons #1

(Lock) and Button #2 (unlock) together for about 3 seconds until 3 chirps are heard. Repeat this step to exit

via the remote transmitter. Lock/Unlock and AUX features will still operate in when in VALET mode however

remote start and alarm functions are inhibited.

Valet Park Mode (Using the remote transmitter only)

Note: Valet Park mode is only accessible when using the remote transmitter. Valet park mode allows you to

turn over the vehicle to a valet allowing access to drive/lock/unlock your vehicle, but alarm will trigger if the

trunk is opened. To activate Valet Park, press and hold both buttons #1 (Lock) and Button #2 (unlock)

together for about 6 seconds. 3 chirps will be heard first when unit goes into regular Valet and as you

continue to hold both buttons you will hear 2 more chirps. LED will flash slowly when in Valet Park. Repeat

step to exit Valet Park mode.

Optional M.A.P. (Mobile Accessories Protection)

This system can be programmed to provide Crimestopper’s unique M.A.P. (Mobile Accessories Protection)

feature that allows you to prevent unauthorized access of your vehicles Audio, Cellular, Navigation, or

Entertainment systems. This feature is OPTIONAL and will requires extra parts and labor for installation.

Consult your installation dealer about MAP before or during installation. The CS2011RS must be

programmed for MAP operation. When the system is put into Valet Park mode, M.A.P. will prevent stereo,

entertainment, navigation, or cellular system from being used.

LED DIAGNOSTICS

The CS-2011RS system includes disarm diagnostics, through the RED LED light, that will help in determining

what caused the last trigger of the alarm system. This is a valuable tool in determining how the vehicle was

tampered with or if there is a false alarm problem in which case you can make the necessary adjustments to

correct the problem. When the system is disarmed with the remote you will hear the normal 2 chirps, then 4

quick chirps that indicate the alarm was triggered while you were away. Check the LED light for a sequence

of flashes:

Shock Sensor = 1 Flash Door = 2 Flashes Hood/Trunk = 3 Flashes Ignition = 4 Flashes

Diagnostics will reset when the Ignition is turned on or when the system is re-armed.

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING -SUCCESSFUL START

1) Press remote start button on the remote transmitter. System will chirp 3 times for audible confirmation.

(Chirps can be programmed on or off-See installation manual.)

2) Parking lights flash once, then turn on solid, Ignition/Accessory circuits turn on.

3) After 6 seconds Starter Motor engages, Parking lights and Accessory circuits turn off while cranking.

4) Engine Starts and Runs. Parking Lights and Accessory turn back on, Doors Lock.

5) Engine will remain running for programmed run time until reset with Brake pedal. If needed, the engine can

be turned off with remote transmitter.

REMOTE ENGINE STARTING -SUCCESSFUL START DIAGRAM:

AFTER

IGN 3STARTER

THEN

FLASH 1X

SOLID

SEC.

START

REMOTE ENGINE CONTROL

REMOTE ENGINE STARTING -UNSUCCESSFUL START

In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then

attempts to restart the engine a 2nd and 3rd time. For hard starting engines, the unit will allow a starter crank

time of up to13 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to

13 seconds to help prevent damage to the starter from over cranking.

1) If engine starts on 2nd or 3rd attempt, see steps 4 & 5 above of "Successful Start".

2) If Third attempt fails to start engine, the system will turn off and doors will remain locked. NO FURTHER

ATTEMPTS WILL BE MADE AUTOMATICALLY UNLESS YOU PRESS THE REMOTE START BUTTON

AGAIN.

TURNING OFF A REMOTE STARTED ENGINE:

1) Engine is running in Remote Start (Parking lights ON).

2) Press Remote Start button on remote transmitter.

3) Engine & parking lights turn OFF, Doors remain locked or will re-lock if applicable.

TURNING OFF A REMOTE STARTED ENGINE DIAGRAM:

START

IDLE DOWN MODE

This mode allows the unit to take over operation of the parked vehicle while the ignition key is removed and

you exit the vehicle. The vehicle is put into a remote running condition before you exit and it will remain

running for the programmed run time, until you return, or until the remote start button is pressed. Examples:

Youpulluptoaconveniencestoreforaquickstop,"IdleDown"modekeepsenginerunningwhenyou

exitthevehicle,(withkeysinhand)remotelock/armalarm.Whenyoureturn,unlock/disarmalarm,turn

ignitionONanddriveaway.ThismodecanalsobeusedonTurbovehiclesthatneedidleforcool-down.

REMOTE ENGINE CONTROL

IDLE DOWN MODE -EXITING THE VEHICLE:

1) With engine running, press Remote Start button on remote transmitter. Siren will chirp 3 times for

confirmation.

2) Parking Lights will turn ON.

3) Doors will unlock, orif brake pedal is being depressed doors will unlock when it is released.

4) Turn OFF Ignition and remove key. Engine should remain running.

5) Exit vehicle then remote lock doors if desired.

6) Engine will remain running for programmed run time, until you return, or press the remote start button.

IGN

SOLID

OFF

UNLOCK

START

ENTERING A VEHICLE DURING “IDLE-DOWN” or “INFINITY RUN” MODES:

1) With engine running in "IDLE DOWN", Remote Unlock/Disarm system (If armed) or open door with key.

2) Enter vehicle and be careful not to step on brake pedal! (Remote Start Reset)

3) Turn Ignition to ON/RUN position, then press brake pedal to reset the Remote Starter. Parking lights will

turn off. Then drive away.

INFINITY RUN MODE

This mode allows the vehicle’s engine to remain running INDEFINITELY. This mode can be beneficial to law

enforcement vehicles or commercial vehicles that need to remain running unattended for long periods of time.

INFINITY RUN MODE –EXITING THE VEHICLE:

1) Follow steps above for “IDLE DOWN MODE -EXITING THE VEHICLE”, except press the remote start

button TWO times at STEP #1.

2) Parking Lights will start flashing instead of coming on solid, and doors will unlock.

3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.

4) The vehicle’s parking lights will flash for the programmed run time of 12, 24, or 36, or 48 minutes and then

switch to solid while motor runs indefinitely or until fuel supply runs out.

REMOTE ENGINE CONTROL

TIMED SELF START MODE

This mode allows the vehicle to be programmed to self-start every 4 hours and run for the programmed run

time. This can be helpful during extremely cold conditions where engine fluid freeze-up is a concern. THE

VEHICLE MUST BE OUTDOORS OR IN A WELL VENILATED AREA.

TIMED SELF-START MODE –EXITING THE VEHICLE:

1) Have engine running with the Key, then press the Start button on the transmitter.

2) Within 10 seconds press the valet/program button once.

3) Parking Lights will turn OFF for about 5 seconds, and doors will unlock.

4) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running.

5) To turn off the engine, press the remote start button. The parking lights will flash 4 TIMES as a

confirmation that the unit is in Timed Self-Start Mode.

6) The Vehicle will Start by itself every 4 hours until driven with key or started via remote control.

RESETTING TIMED SELF START MODE

To reset the timed self-start mode, start the vehicle using the key or the remote control

ANTI CARJACK PROTECTION

REMOTE OPERATED CARJACK PROTECTION

This feature provides Active Carjack protection through the remote control. When the Ignition is on (vehicle is

running), press and hold the #1 LOCK Button and #3 TRUNK Button for 2 seconds. The parking lights will

flash 2 times and the LED will begin to flash rapidly to confirm the beginning of a Carjack countdown. 30

Seconds later, the unit will begin a Carjack Cycle consisting of 20 seconds of pre-warning chirps turning into a

full system activation with siren / flashing light pulses for up to 5 min. If the Ignition is turned off during a

Carjack trigger the siren and lights stop but Carjack protection is still active. The Siren and Lights will resume

if the Carjacker tries to turn the Ignition back ON. TO RESET: Press Button #2 (UNLOCK) on the remote and

the siren will chirp once, or turn the key on and press and hold the override button for at least 5 seconds.

SWITCH-CONTROLLED & FULL TIME CARJACK (PINK WIRE CONFIGURATION)

This feature can provide Passive or Manual control Carjack protection depending on the configuration of the

Pink Carjack wire of the alarm system. The system must programmed for the Pink wire to be used as a

Carjack trigger at Option #8. Once programmed for the Pink wire to serve as a Carjack trigger, it can be

configured in different ways to provide different levels of protection. It can be connected to a hidden +12V

toggle/momentary switch or to +12V Ignition Power. Read the sections below for further descriptions.

ANTI CARJACK PROTECTION

SWITCH-CONTROLLED CARJACK:

This configuration will enable the vehicle owner to activate a Carjack countdown by pressing a hidden push-

button (not included with kit) during a Carjack situation. A Carjack countdown will begin under the following

conditions: Ignition is ON (vehicle is running), the push-button is pressed, and the door opens/closes. Upon

these 3 events, in that order, the alarm will start a Carjack countdown. After a delay of one minute, the system

will begin chirping for 20 seconds then trigger into a full cycle for up to 5 minutes. To reset this Carjack mode,

Ignition must be ON then press and hold the override/valet button for 5 seconds (until LED goes out.)

FULL-TIME [Permanent] CARJACK:

We recommend that this configuration only be used in serious situations. When the Ignition is on (vehicle is

running), anytime a door is opened the Carjack countdown sequence will be initiated. There will be 2 light

flashes and the LED will change from solid to quick pulsing as confirmation of a countdown sequence. To

reset FULL TIME Carjack, the Ignition has to be ON, then press and hold the override/program button 5

seconds until LED stops pulsing. The LED will be on SOLID when in this mode anytime the Ignition is ON (or

while driving) as a reminder that Carjack is waiting for a door to open.

TRANSMITTER PROGRAMMING

Note: RemotesTransmitterscome pre-programmed from the Factory. When re-learning remotes or

adding remotes, ALL your system’s remote codes must be learned at time of programming!! This

system allow storage of up to 4 different remote codes in memory.

1. Open hood (ground the Bluehood pin wire if no hood pin is installed.)

2. Turn key to the ON position. (Starting the vehicle is not necessary.)

3. Press Program/Valet button 4 times. After a few seconds, the unit will flash the parking lights exactly 4

times.

4. Press Button #1 (Lock) of the transmitter to be learned. You should get 2 light flashes indicating the code-

learn. Now the unit is waiting for a 2nd code, so repeat this step as needed with up to 3 additional remotes.

The unit will flash the lights in succession after each code learned for up to 4 codes. (2 flashes for the 2nd

code, 3 flashes for the 3rd code etc.) If all 4 codes are learned, the unit will automatically exit code learning

mode, otherwise turn key OFF and close the hood.

DIAGRAM ON NEXT PAGE

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere CrimeStopper Autoalarmanlage Handbücher

CrimeStopper

CrimeStopper CS-9703 Handbuch

CrimeStopper

CrimeStopper CS-9709 Kurzanleitung

CrimeStopper

CrimeStopper CS-790MX Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2014DP-TW2 Super Page Bedienungsanleitung

CrimeStopper

CrimeStopper SP-302 Bedienungsanleitung

CrimeStopper

CrimeStopper CAS-968 Handbuch

CrimeStopper

CrimeStopper CS-2002DC Series III Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2002DPII Bedienungsanleitung

CrimeStopper

CrimeStopper Gargoyle CS-2001 Handbuch

CrimeStopper

CrimeStopper Super Rage CS-2011DP Systemhandbuch

CrimeStopper

CrimeStopper CS-2003DC II Series Handbuch

CrimeStopper

CrimeStopper Fortress FS-20 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-8716 Handbuch

CrimeStopper

CrimeStopper Super Rage CS-2012TW1 Bedienungsanleitung

CrimeStopper

CrimeStopper Super Page V CS-2014TW2 Bedienungsanleitung

CrimeStopper

CrimeStopper Fortress FS-30 Bedienungsanleitung

CrimeStopper

CrimeStopper Fortress FS-40 Systemhandbuch

CrimeStopper

CrimeStopper SP-200 Bedienungsanleitung

CrimeStopper

CrimeStopper CS-2005.FM Montageanleitung

CrimeStopper

CrimeStopper CS-883 OEM Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9711 Systemhandbuch

CrimeStopper

CrimeStopper CS-2000 Handbuch

CrimeStopper

CrimeStopper CS-9604PI Bedienungsanleitung

CrimeStopper

CrimeStopper CS-9002 Service-Handbuch

Beliebte Autoalarmanlage Handbücher anderer Marken

Clifford

Clifford 3606X Bedienungsanleitung

Ultra Start

Ultra Start 2500M SERIES Bedienungsanleitung

Ultra Start

Ultra Start 650 Series Bedienungsanleitung

Audiovox

Audiovox Prestige Platinum+ APS-511C Bedienungsanleitung

Sparkrite

Sparkrite SRA8 Bedienungsanleitung

Viper

Viper 4708V Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation Pathfinder Siren Series Handbuch

Falcon

Falcon Predator XL3 Benutzerhandbuch

Audiovox

Audiovox Auto Security XR91 Betriebsanleitung

Clifford

Clifford Sabre II Bedienungsanleitung

Scytek electronic

Scytek electronic Vectra X3 Bedienungsanleitung

Clifford

Clifford CYBER 2 Bedienungsanleitung

Gemini

Gemini 7057 Bedienungsanleitung

FlashLogic

FlashLogic FLRSBA PRESTIGE Bedienungsanleitung

Magicar

Magicar FAI-440 Bedienungsanleitung

Clifford

Clifford Nova 3 Bedienungsanleitung

Viper

Viper 560XV Bedienungsanleitung

SECO-LARM

SECO-LARM 300C Bedienungsanleitung